Re: Error in make after make menuconfig (rtai 3.9.2 with Ubuntu 10.04 Lucid Lynx (2.6.32))

Contd. previous mail, I am trying to resolve patch issues for the same.
(Ubuntu Utopic 14_10, 3.16.0 and rtai-3.16-x86-3). Any suggestions/inputs
are welcome if this is still not the right approach.

Thank you

On Thu, Apr 20, 2017 at 9:51 AM, bhargavb <[email protected]> wrote:

> Thank you for the reply.
>
> I have only chosen Lucid Lynx for the reason that it is an LTS version
> presuming it might be better than internediate other versions though its
> support has long been withdrawn. Also, I thought older the rtai patch
> stable would it be and ease my setup and work. I don't actually have any
> other technical reason.
>
> Now, I have taken a later version (Ubuntu Utopic Unicorn 14.10, kernel
> version 3.16.0) and rtai patch (hal-linux-3.16-x86-3.patch) from
> https://github.com/ShabbyX/RTAI/tree/magma .
>
> I am finding it difficult to apply patch, getting Hunk failures (9
> failures, failure log attached) and do not know how to resolve them.
>
> *I need help in this regard as I doubt if I can find patches for any
> kernel and apply without any failures/modifications. I cannot resolve diff
> issues either for hunk failures.*
>
> I would anyways keep searching and trying better matching in kernel
> versions of Ubuntu and rtai, with the hope that I would at least minimise
> the hunk failures to resolve if not none.
>
> Thank you
>
>
> On Wed, Apr 19, 2017 at 2:31 PM, Paolo Mantegazza <
> [email protected]> wrote:
>
>> Just one question: is there any reason to stay on such older RTAI
>> versions?
>> My suggestion is to use a more recent one, supporting Linux 3 and 4, in
>> which 64-32 bits are unified, e.g. rtai-5.0-test2 or Vulcano CVS.
>> Paolo
>>
>>
>> On 04/19/2017 05:03 AM, bhargavb wrote:
>>
>> Dear team,
>>
>> I need to work on rtai patch for porting and testing an application in
>> real time mode.
>>
>> My machine is 64 bit, so I was looking for patches and I have no
>> preference on version of kernel except that it should be at least 2.6
>> kernel to apply patch.
>>
>> Question 1:
>> I chose Lucid Lynx (Ubnutu 10.04 with 2.6.32 kernel version) and
>> realized that rtai 3.8 is that last one in 2.6 kernel with patches in
>> x86_64 folder for patching my x86_64 machine.
>> But then, as per one of answers in rtai mailing lists, I realized that
>> the standard is not strictly followed to keep the patches for 64 bit
>> in x86_64 directory, and x86 directory containing patches for 32 bit
>> version can be used for an x86_64 machine. So, I chose rtai-3.9.2
>> (2.6.32-20 kernel patch)  for patching Ubuntu 10.04 (2.6.32). Kindly
>> confirm if this is acceptable.
>>
>> Question 2:
>> As per above way,  and installation how to text file in rtai.org, I
>> followed steps till make menuconfig and make clean. Then I did make
>> where am getting error. Log is attached.
>> Kindly guide.
>>
>> Note: I do not have preference on Ubuntu version to apply rtai patch.
>> Can do on any Ubuntu 64 bit version which has stable rtai patch.
>>
>> Thanks and regards,
>> Bhargav
>>
>>
>>
>> _______________________________________________
>> Rtai mailing [email protected]://mail.rtai.org/cgi-bin/mailman/listinfo/rtai
>>
>>
>>
>> _______________________________________________
>> Rtai mailing list
>> [email protected]
>> https://mail.rtai.org/cgi-bin/mailman/listinfo/rtai
>>
>
>
>
> --
> Bhargav
>



-- 
Bhargav

_______________________________________________
Rtai mailing list
[email protected]
https://mail.rtai.org/cgi-bin/mailman/listinfo/rtai