PPPD LCP problem

Hi

I am trying to run PPP over GPRS and getting an error during LCP
negotiation. These are the commands used to set up the serial line
before starting pppd.

AT+CGACT=1
ATGDCONT=1,"IP","portalnmms"
AT+CGACT=1,1

ATZ
ATE0V1
ATD*99***1#

It gives back... CONNECT 115200 and then crap

After this i start PPPD:

pppd 115200 ttyS1 crtscts local novj nomagic name gprs debug kdebug 7
nodetach asyncmap 0 defaultroute usepeerdns

This is the output from pppd:

Connect: ppp0 <--> /dev/ttyS1
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x1 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x1 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x2 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x2 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x3 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x3 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x4 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x4 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x5 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x5 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x6 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x6 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x7 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x7 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x7 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x7 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x8 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x8 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x9 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0x9 <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0xa <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
sent [LCP ConfAck id=0xa <mru 1500> <asyncmap 0x0> <pcomp> <accomp>
<auth pap>]
LCP: timeout sending Config-Requests
Connection terminated.

It just seems the server doesnt understand any of the thing which the
module sends. It keeps repeating its request, and never sends back a
ConfAck.

I would be very grateful if someone could help and hint at why this is
happening.

thanks in advance

ritun
([email protected])