Re: Assessing USB Mass Storage devices - Debugging Info

Hi (again)

I have now compiled linux-2.4.19-ac2 with USB Mass Storage degugging
Information.

If anyone can make some sence of this, I would be very gratefull for any
more assistance :-)

Please find the output of dmesg -n 9, when I plugged the camera in.
I still cannot access it by any method I have tried or been advised to
try on this list.

Below is the stderror output to my terminal on plugging in the camera.
I have now noticed that it prints sda1 up, where as last time it never.
I have tried to access sda1, but every time keep getting:

mount: /dev/sda1 is not a valid block device

[root@stimpy mark]# usb.c: USB device 2 (vend/prod 0x733/0x1310) is not
claimed by any active driver.
  Vendor:           Model: 1.3M DigitalCAM   Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 16384 512-byte hdwr sectors (8 MB)
sda: test WP failed, assume Write Enabled
 sda1


Sorry for the long list in advance

---------------------- cut -----------------------------

hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x733/0x1310) is not claimed by any
active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 85
usb-storage: Array length appears to be: 87
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xdb6b0b20 Out: 0xdb6b0b34 Int: 0xdb6b0b48
(Period 1)
usb-storage: New GUID 07331310000ffffffffff700
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 4f da d4 33 4f da
usb-storage: Bulk command S 0x43425355 T 0x8 Trg 0 LUN 0 L 255 F 128 CL
6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 36/255
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x8 R 219 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
  Vendor:           Model: 1.3M DigitalCAM   Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6/0)
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7/0)
usb-storage: *** thread sleeping.
Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00 00 00 00 00 30 da
usb-storage: Bulk command S 0x43425355 T 0x10 Trg 0 LUN 0 L 0 F 0 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x10 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00 30 da
usb-storage: Bulk command S 0x43425355 T 0x11 Trg 0 LUN 0 L 8 F 128 CL
10
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 8 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 8/8
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x11 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sda: 16384 512-byte hdwr sectors (8 MB)
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 3f 00 ff 00 00 00 00 00 30 da
usb-storage: Bulk command S 0x43425355 T 0x12 Trg 0 LUN 0 L 255 F 128 CL
6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: usb_stor_bulk_msg() returned -32 xferred 0/255
usb-storage: clearing endpoint halt for pipe 0xc0038280
usb-storage: usb_stor_clear_halt: result=0
usb-storage: usb_stor_transfer_partial(): unknown error
usb-storage: Bulk data transfer result 0x2
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x12 R 255 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk command S 0x43425355 T 0x12 Trg 0 LUN 0 L 18 F 128 CL
6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 18 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x12 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x5, ASC: 0x24, ASCQ: 0x0
usb-storage: Illegal Request: invalid field in CDB
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
sda: test WP failed, assume Write Enabled
 sda:<7>usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 08 00 30 da
usb-storage: Bulk command S 0x43425355 T 0x13 Trg 0 LUN 0 L 4096 F 128
CL 10
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 4096 bytes
usb-storage: usb_stor_bulk_msg() returned 0 xferred 4096/4096
usb-storage: usb_stor_transfer_partial(): transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: Bulk status result = 0
usb-storage: Bulk status Sig 0x53425355 T 0x13 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
 sda1
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
cdrom: This disc doesn't have any tracks I recognize!

---------------------- cut -----------------------------

I will be doing some more searching on some of the information for
dmesg, but to be honest most of it baffles me, as its kernel debugging
output.

I will be posting this to both then usb and kernel mailing lists to try
to get some more information.

Mark

-- 
---
To steal ideas from one person is plagiarism;
to steal from many is research.