Re: clamav 0.96.2

  Hi Axel,

Just upgraded to 1:clamav-0.96.2-53.fc13.i686 - and it works fine!

Thanks!
Kim

On 22-08-2010 10:46, Kim Bisgaard wrote:
>   Hi Axel,
>
> Have been running my own version for the past days without problems.
>
> I have just tried upgrading to your version, but it segmentation 
> faults. Perhaps the mailer did something to the patch I sent inline, 
> like breaking long lines, so that it does not apply cleanly? I have 
> attatched my version of the file.
>
> Regards,
> Kim
>
> On 18-08-2010 19:35, Kim Bisgaard wrote:
>> I have just seen a new page at clamav:
>> https://wiki.clamav.net/Main/UpgradeNotes0962
>>
>> which has this patch I'm just rebuild and is about to try out - just
>> hang on .... :
>> --- a/ChangeLog
>> +++ b/ChangeLog
>> @@ -1,3 +1,7 @@
>> +Fri Aug 13 13:57:04 EEST 2010 (edwin)
>> +--------------------------------------
>> + * libclamav/bytecode_detect.c: prevent fclose(NULL) on SELinux (bb
>> #2200)
>> +
>>  Thu Aug 12 18:49:37 CEST 2010 (tk)
>>  ----------------------------------
>>   * V 0.96.2
>> diff --git a/libclamav/bytecode_detect.c b/libclamav/bytecode_detect.c
>> index 6311314..9271fc7 100644
>> --- a/libclamav/bytecode_detect.c
>> +++ b/libclamav/bytecode_detect.c
>> @@ -109,9 +109,11 @@ static int detect_SELinux(void)
>>      f = fopen("/selinux/enforce", "r");
>>          if (!f && errno == EACCES)
>>          return 2;
>> -    if (fscanf(f, "%d", &enforce) == 1)
>> +    if (f) {
>> +        if (fscanf(f, "%d", &enforce) == 1)
>>          selinux = 2;
>> -    fclose(f);
>> +        fclose(f);
>> +    }
>>      return selinux;
>>      }
>>      while (fgets(line, sizeof(line), f)) {
>> @@ -130,8 +132,8 @@ static int detect_SELinux(void)
>>          selinux = 2;
>>      if (enforce == -1)
>>          selinux = 0;
>> +    fclose(f);
>>      }
>> -    fclose(f);
>>      return selinux;
>>  }
>>
>> On 18-08-2010 17:26, Axel Thimm wrote:
>>> Hi,
>>>
>>> On Fri, 2010-08-13 at 11:41 +0200, Kim Bisgaard wrote:
>>>> Hi,
>>>>
>>>> I have tried to build (change the spec to above version) the newly
>>>> released clamav-0.96.2. It builds ok once one adds 'BuildRequires:
>>>> sendmail-milter', *BUT* here it core dumps once I try to run it.
>>>>
>>>> I have tried to get the debug-symbols, and starting clamd in gdb but
>>>> when started in debugger it does not core dump :-( could be a selinux
>>>> thing - but I have not found any AVC's that makes the core dump go
>>>> away.
>>>>
>>>> This is f13 and i686.
>>>>
>>>> I advice to hold off the update until a patch shows up.
>>>
>>> Thanks for the heads-up. I did build it, but I placed it under 
>>> bleeding:
>>>
>>> http://packages.atrpms.net/name/clamav/
>>>
>>> Can you check whether this build exhibits the same issues like you
>>> describe above? Thanks!
>>
>> _______________________________________________
>> atrpms-devel mailing list
>> [email protected]
>> http://lists.atrpms.net/mailman/listinfo/atrpms-devel
>
>
> _______________________________________________
> atrpms-devel mailing list
> [email protected]
> http://lists.atrpms.net/mailman/listinfo/atrpms-devel