Re: mythtv .27 centos 7 rpm feedback

On 25/02/2015 7:03 pm, Stephen Collier wrote:
> On 25/02/2015 6:07 PM, Barry Quiel wrote:
>>
>>
>> On 2/24/2015 9:53 PM, Stephen Collier wrote:
>>> On 25/02/2015 3:19 PM, Barry Quiel wrote:
>>>>
>>>>
>>>> On 2/24/2015 1:20 AM, Duncan Brown wrote:
>>>>> On 24/02/2015 06:38, Stephen Collier wrote:
>>>>>> On 24/02/2015 4:08 pm, Barry Quiel wrote:
>>>>>>> Stephen -
>>>>>>>
>>>>>>> Thanks for the CentOS7 packages of .27.  I have been looking for 
>>>>>>> them
>>>>>>> for a while.  A quick piece of feedback.  It looks like 
>>>>>>> python-Mythtv
>>>>>>> is missing a dependency.  None of the metadata lookups would work
>>>>>>> until I added python-lxml.  It didn't get added as a dependency. 
>>>>>>> This
>>>>>>> could be my issue however.  I used the CentOS minimal install disk
>>>>>>> and added from there.  It's possible that python-lxml would get
>>>>>>> installed from a "normal install"
>>>>>>>
>>>>>>> Also one request:  Any chance your next build of mythtv you could
>>>>>>> include hdmi-cec support?  I installed libcec from your repo and 
>>>>>>> can
>>>>>>> see the cec traffic with my pulse8 adapter.  The key presses just
>>>>>>> aren't getting into mythfrontend.  I did a mythfrontend 
>>>>>>> --version and
>>>>>>> didn't see cec listed.  My guess is that you didn't compile in cec
>>>>>>> support in myth, but I could be doing it wrong too.
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> atrpms-users mailing list
>>>>>>> [email protected]
>>>>>>> http://lists.atrpms.net/mailman/listinfo/atrpms-users
>>>>>>>
>>>>>> Barry,
>>>>>>
>>>>>> Thanks for the info. I'll add it to the build. I've tried a 
>>>>>> couple of
>>>>>> times to get cec in the build (not too hard) but it ignores it at
>>>>>> configure time. If I know someone wants it I'll have a much harder
>>>>>> look as I wanted to include it in the original builds.
>>>>>>
>>>>>> Cheers
>>>>>> Stephen
>>>>>>
>>>>>> _______________________________________________
>>>>>> atrpms-users mailing list
>>>>>> [email protected]
>>>>>> http://lists.atrpms.net/mailman/listinfo/atrpms-users
>>>>> I think it needs this patch to work with the version of libcec I 
>>>>> assume
>>>>> you are using
>>>>>
>>>>> https://code.mythtv.org/trac/ticket/11338
>>>>>
>>>>> _______________________________________________
>>>>> atrpms-users mailing list
>>>>> [email protected]
>>>>> http://lists.atrpms.net/mailman/listinfo/atrpms-users
>>>>
>>>> So no luck on the new packages.  I'm not sure if its actually getting
>>>> compiled in.  I recall you mentioning you were have problems and it
>>>> was being ignored by configure.  When I do a mythfrontend --version I
>>>> would expect to see something like using_cec or using_libcec. I don't
>>>> see that, but I could be wrong.  I also don't see mythfrontend linked
>>>> against libcec.  But it's possible that they aren't linking against
>>>> the library and just reading raw from the /dev/tty.  In that case all
>>>> my assumptions would be incorrect.
>>>>
>>>> _______________________________________________
>>>> atrpms-users mailing list
>>>> [email protected]
>>>> http://lists.atrpms.net/mailman/listinfo/atrpms-users
>>>>
>>> Barry,
>>>
>>> Sorry the new packages built before I made the changes. Automatic 
>>> builds
>>> help me not have to keep kicking them off but they sometimes build at
>>> the wrong time. The 27.4-20 rpms are the ones you need. They should
>>> build over the next couple of hours. Mock which is part of the build
>>> system broke so I had to patch it before anything would build hence the
>>> delay.
>>>
>>> Let me know if it works. It should be there soon.
>>>
>>> Cheers
>>> Stephen
>>>
>>> _______________________________________________
>>> atrpms-users mailing list
>>> [email protected]
>>> http://lists.atrpms.net/mailman/listinfo/atrpms-users
>>
>> Unfortunately it's still not working.  But its not a myth problem its 
>> a libcec problem.  Basically the library can't find the /dev/tty that 
>> the adapter is plugged into.  So since it can't find it it can't give 
>> it to mythfrontend.  I don't see any method or config file option to 
>> specify so that the library can find the /dev/tty without the 
>> detection code.
>>
>> The error is:
>> libCEC has not been compiled with detection code for the Pulse-Eight 
>> USB-CEC Adapter, so the path to the COM port has to be provided to 
>> libCEC if this adapter is being used
>>
>> Here is where I got libcec from ;)
>> libcec.x86_64        2.1.3-2.el7   @scrpms
>> libcec-devel.x86_64  2.1.3-2.el7   scrpms
>>
>> If I can find the time maybe I will take a crack at trying to compile 
>> libcec with detection code.  I'd probably be playing a bit of 
>> catch-up considering you have already packaged it, so have a build 
>> script.
>>
>> _______________________________________________
>> atrpms-users mailing list
>> [email protected]
>> http://lists.atrpms.net/mailman/listinfo/atrpms-users
>>
> You can start with the src rpm and unpack
> rpm2cpio libcec-2.1.3-2.el6.src.rpm | cpio -iv
>
> libcec 2.4 is out so that is probably the place to start
>
> I may have a look tomorrow if I have time.
>
> Cheers and good luck
> Stephen
>
> _______________________________________________
> atrpms-users mailing list
> [email protected]
> http://lists.atrpms.net/mailman/listinfo/atrpms-users
>
my mistake libcec 2.2.0 is current