Re: How to install new app on Client image without update

HI Alkis,
You are right!
I will start new installation
If still no works I think change to Opensuse Or Ubuntu Mate!

Thanks


Em seg, 8 de abr de 2019 às 11:13, Alkis Georgopoulos <[email protected]>
escreveu:

> Hi Douglas,
>
> so, your installation is very broken;
> I would advice to start a new one,
> AND stop when you see any errors,
> and report them here.
>
>
> On 4/8/19 4:50 PM, Douglas G. Oechsler wrote:
> > Hello Alkis!
> >
> > Em sáb, 6 de abr de 2019 às 16:26, Alkis Georgopoulos <[email protected]
> > <mailto:[email protected]>> escreveu:
> >
> >     Thin or fat clients?
> >     I imagine fat clients.
> >
> > Yes, fat client
> >
> >     Login to a client. Create a test.txt file on the desktop.
> >     Open a terminal on the client and run:
> >     mount | grep /home
> >
> >
> > Strange that, when did open terminal, it show only $ at the prompt.
> > I made command :
> > mount | grep /home and no answer, not show some result, nothing
> >
> >     You're suppose to see that /home/username is an sshfs mount.
> >     Reboot the client, login again.
> >     Is test.txt still there?
> >
> > No, the file not exist more and after reboot, run a New Image LTSP client
> >
> > Sad!
> >
> > Thank you attention
> >
> > Douglas
> >
> >
> >
> >
> >
> >
> >     On 4/6/19 9:11 PM, Douglas G. Oechsler wrote:
> >      > Hello Alkis
> >      >
> >      > *Which distro/flavor/ltsp version are you using?*
> >      > Linux Mint 19.1 64 bits
> >      >
> >      > *did you follow the official tutorial?*
> >      > Yes: http://wiki.ltsp.org/wiki/Installation/Ubuntu
> >      > pnp mode
> >      > Dnsmasq - single NIC
> >      > dnsmasq --enable-dns (run ok without errors)
> >      > and config the same subnet that my scenario
> >      >
> >      > *other chnage:  /etc/sysctl.conf*
> >      > *from:* # Uncomment the next line to enable packet forwarding for
> >     IPv4
> >      > #net.ipv4.ip_forward=1
> >      > *To:*
> >      > net.ipv4.ip_forward=1
> >      >
> >      > *The commad used to update image:*
> >      > apt install xxx && ltsp-update-image -c /
> >      > The same that official tutorial
> >      >
> >      >
> >      > *Are you using any weird scripts for guest accounts etc?*
> >      > No! Only using adduser command
> >      >
> >      > Thank you
> >      >
>
>
> _____________________________________________________________________
> Ltsp-discuss mailing list.   To un-subscribe, or change prefs, goto:
>       https://lists.sourceforge.net/lists/listinfo/ltsp-discuss
> For additional LTSP help,   try #ltsp channel on irc.freenode.net
>


-- 
Douglas Giovani Oechsler

_____________________________________________________________________
Ltsp-discuss mailing list.   To un-subscribe, or change prefs, goto:
      https://lists.sourceforge.net/lists/listinfo/ltsp-discuss
For additional LTSP help,   try #ltsp channel on irc.freenode.net