Re: USB bus numbering

On 2/28/07, Alan Stern <[email protected]> wrote:
> I can't tell just from the end results.  Post the dmesg log showing what
> happened during boot-up and we'll see.

-- 
Jon Smirl
[email protected]

Linux version 2.6.20 (jonsmirl@jonsmirl) (gcc version 4.1.2 20060928
(prerelease) (Ubuntu 4.1.1-13ubuntu5)) #32 SMP Sun Feb 4 17:26:36 EST
2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 00000000000a0000 end:
00000000000a0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end:
0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000009fe74000 end:
000000009ff74000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000009ff74000 size: 0000000000002000 end:
000000009ff76000 type: 4
copy_e820_map() start: 000000009ff76000 size: 0000000000021000 end:
000000009ff97000 type: 3
copy_e820_map() start: 000000009ff97000 size: 0000000000069000 end:
00000000a0000000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end:
00000000fec10000 type: 2
copy_e820_map() start: 00000000fecf0000 size: 0000000000001000 end:
00000000fecf1000 type: 2
copy_e820_map() start: 00000000fed20000 size: 0000000000070000 end:
00000000fed90000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000010000 end:
00000000fee10000 type: 2
copy_e820_map() start: 00000000ffb00000 size: 0000000000500000 end:
0000000100000000 type: 2
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000009ff74000 (usable)
 BIOS-e820: 000000009ff74000 - 000000009ff76000 (ACPI NVS)
 BIOS-e820: 000000009ff76000 - 000000009ff97000 (ACPI data)
 BIOS-e820: 000000009ff97000 - 00000000a0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
1663MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
Entering add_active_range(0, 0, 655220) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   655220
early_node_map[1] active PFN ranges
    0:        0 ->   655220
On node 0 totalpages: 655220
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 3326 pages used for memmap
  HighMem zone: 422518 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 DELL                                  ) @ 0x000feb90
ACPI: RSDT (v001 DELL    PE400SC 0x00000008 ASL  0x00000061) @ 0x000fd14f
ACPI: FADT (v001 DELL    PE400SC 0x00000008 ASL  0x00000061) @ 0x000fd187
ACPI: SSDT (v001   DELL    st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffc8efd
ACPI: MADT (v001 DELL    PE400SC 0x00000008 ASL  0x00000061) @ 0x000fd1fb
ACPI: BOOT (v001 DELL    PE400SC 0x00000008 ASL  0x00000061) @ 0x000fd267
ACPI: ASF! (v016 DELL    PE400SC 0x00000008 ASL  0x00000061) @ 0x000fd28f
ACPI: DSDT (v001   DELL    dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at a8000000 (gap: a0000000:5ec00000)
Detected 2793.054 MHz processor.
Built 1 zonelists.  Total pages: 650102
Kernel command line: root=UUID=f41a7b1a-8d3e-4f7d-b672-5a4fc25c2cba ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2591428k/2620880k available (1887k kernel code, 28104k
reserved, 869k data, 216k init, 1703376k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4f000 - 0xfffff000   ( 704 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc03b8000 - 0xc03ee000   ( 216 kB)
      .data : 0xc02d7dda - 0xc03b1454   ( 869 kB)
      .text : 0xc0100000 - 0xc02d7dda   (1887 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5590.02 BogoMIPS (lpj=11180058)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080
00004400 00000000 00000000
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5586.41 BogoMIPS (lpj=11172827)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080
00004400 00000000 00000000
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (11176.44 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=134
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfba6d, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15)
SCSI subsystem initialized
libata version 2.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: fc000000-feafffff
  PREFETCH window: d4000000-efffffff
PCI: Bridge: 0000:00:1e.0
  IO window: d000-dfff
  MEM window: fbf00000-fbffffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3346k freed
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
audit: initializing netlink socket (disabled)
audit(1172652581.212:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Real Time Clock Driver v1.12ac
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin
is 60 seconds).
Hangcheck: Using get_cycles().
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
ata_piix 0000:00:1f.1: version 2.00ac7
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15
scsi0 : ata_piix
ata1.00: ATA-6, max UDMA/100, 488397168 sectors: LBA48
ata1.00: ata1: dev 0 multi count 8
ata1.00: configured for UDMA/100
scsi1 : ata_piix
ata2.00: ATAPI, max UDMA/33
ata2.01: ATAPI, max UDMA/66
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      HDS722525VLAT80  V36O PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM            LITE-ON  LTR-52246S       6S0F PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM            DVDRW    IDE1008          0060 PQ: 0 ANSI: 5
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata3: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 16
ata4: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 16
scsi2 : ata_piix
ata3.00: ATA-7, max UDMA/100, 390721968 sectors: LBA48 NCQ (depth 0/32)
ata3.00: ata3: dev 0 multi count 8
ata3.00: configured for UDMA/100
scsi3 : ata_piix
scsi 2:0:0:0: Direct-Access     ATA      Maxtor 6V200E0   VA11 PQ: 0 ANSI: 5
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 216k freed
Time: tsc clocksource has been installed.
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
 sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 >
sd 2:0:0:0: Attached scsi disk sdb
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 17
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17]
MMIO=[fbfdf800-fbfdffff]  Max Packet=[2048]  IR/IT contexts=[8/8]
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 18, io mem 0xffa80800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
md: raid1 personality registered for level 1
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000ff80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000ff60
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000ff40
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000ff20
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-1: configuration #1 chosen from 1 choice
md: md0 stopped.
md: bind<sdb5>
md: bind<sda2>
raid1: raid set md0 active with 2 out of 2 mirrors
usb 1-3: new high speed USB device using ehci_hcd and address 3
usb 1-3: configuration #1 chosen from 1 choice
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 7 ports detected
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00006ec051]
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
hub 3-2:1.0: USB hub found
hub 3-2:1.0: 4 ports detected
usb 1-3.5: new high speed USB device using ehci_hcd and address 5
usb 1-3.5: configuration #1 chosen from 1 choice
usb 3-2.1: new low speed USB device using uhci_hcd and address 3
usb 3-2.1: configuration #1 chosen from 1 choice
usb 3-2.2: new full speed USB device using uhci_hcd and address 4
usb 3-2.2: configuration #1 chosen from 1 choice
usb 3-2.3: new full speed USB device using uhci_hcd and address 5
usb 3-2.3: configuration #1 chosen from 1 choice
usb 3-2.4: new full speed USB device using uhci_hcd and address 6
usb 3-2.4: configuration #1 chosen from 1 choice
Linux agpgart interface v0.101 (c) Dave Jones
input: PC Speaker as /class/input/input0
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
scsi 1:0:1:0: Attached scsi generic sg2 type 5
sd 2:0:0:0: Attached scsi generic sg3 type 0
agpgart: Detected an Intel i875 Chipset.
agpgart: AGP aperture is 64M @ 0xd0000000
sr0: scsi3-mmc drive: 8x/8x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
Intel(R) PRO/1000 Network Driver - version 7.3.15-k2
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 18 (level, low) -> IRQ 16
e1000: 0000:02:0c.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:55:4b:7e
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
usbcore: registered new interface driver hiddev
input: Logitech USB Receiver as /class/input/input1
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.1-2.1
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-2.1
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
NVRM: loading NVIDIA UNIX x86 Kernel Module  1.0-9746  Fri Dec 15
09:54:45 PST 2006
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 55626 usecs
intel8x0: clocking to 48000
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 20
Adding 498004k swap on
/dev/disk/by-uuid/43f20f7a-45c0-42ef-be58-97a884f05bda.  Priority:-1
extents:1 across:498004k
NET: Registered protocol family 17
EXT3 FS on sda5, internal journal
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [VBTN]
Using specific hotkey driver
Capability LSM initialized
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
**WARNING** I2C adapter driver [NVIDIA i2c adapter 0 at 1:00.0] forgot
to specify physical device; fix it!
**WARNING** I2C adapter driver [NVIDIA i2c adapter 1 at 1:00.0] forgot
to specify physical device; fix it!
**WARNING** I2C adapter driver [NVIDIA i2c adapter 2 at 1:00.0] forgot
to specify physical device; fix it!
Installing knfsd (copyright (C) 1996 [email protected]).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
cdrom: sr0: mrw address space DMA selected
UDF-fs: No VRS found
cdrom: sr0: mrw address space DMA selected
UDF-fs: No VRS found
cdrom: sr0: mrw address space DMA selected
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
UDF-fs: No VRS found
UDF-fs: No VRS found
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel