Re: USB misbehavior causes system hang

> On Tue, 27 Feb 2007 09:06:21 -0500 Eric Buddington <[email protected]> wrote:
> 2.6.20-mm2 #1 Mon Feb 26 13:16:04 EST 2007 i686 unknown
> 
> I have an external USB drive (WD MyBook 5000YS), which I use for backups.
> 
> When I try to back up to it, it works for a while, but inevitably
> starts resetting like mad, gives I/O errors, and then (here's the
> problem), the softdog module reboots the system.
> 
> ---------------------------
> scsi1 : SCSI emulation for USB Mass Storage devices
> input: Western Digital External HDD as /class/input/input8
> input: USB HID v1.11 Device [Western Digital External HDD] on usb-0000:00:03.2-6
> .2
> scsi 1:0:0:0: Direct-Access     WD       5000YS External  106a PQ: 0 ANSI: 4
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> sda: Write Protect is off
> sda: assuming drive cache: write through
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> sda: Write Protect is off
> sda: assuming drive cache: write through
>  sda: sda1 sda2
> sd 1:0:0:0: Attached scsi disk sda
> sd 1:0:0:0: Attached scsi generic sg0 type 0
> reiser4[pdflush(194)]: disable_write_barrier (fs/reiser4/wander.c:234)[zam-1055]
> :
> NOTICE: md1 does not support write barriers, using synchronous write instead.
> reiser4: sda2: found disk format 4.0.0.
> 
> ---- (works fine here for a while, then:) ----------
> 
> usb 1-6.2: reset high speed USB device using ehci_hcd and address 36
> usb 1-6.2: device descriptor read/64, error -110
> usb 1-6.2: device descriptor read/64, error -110
> usb 1-6.2: reset high speed USB device using ehci_hcd and address 36
> usb 1-6.2: device descriptor read/64, error -110
> usb 1-6.2: device descriptor read/64, error -110
> usb 1-6.2: reset high speed USB device using ehci_hcd and address 36
> usb 1-6.2: device descriptor read/8, error -110
> usb 1-6.2: device descriptor read/8, error -110
> usb 1-6.2: reset high speed USB device using ehci_hcd and address 36
> usb 1-6.2: device descriptor read/8, error -110
> usb 1-6.2: device descriptor read/8, error -110
> sd 1:0:0:0: scsi: Device offlined - not ready after error recovery
> sd 1:0:0:0: SCSI error: return code = 0x00050000
> end_request: I/O error, dev sda, sector 919931588
> sd 1:0:0:0: rejecting I/O to offline device
> sd 1:0:0:0: SCSI error: return code = 0x00010000
> end_request: I/O error, dev sda, sector 919931828
> sd 1:0:0:0: rejecting I/O to offline device
> sd 1:0:0:0: rejecting I/O to offline device
> sd 1:0:0:0: rejecting I/O to offline device

Does 2.6.20 do this?  2.6.21-rc1?


-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel