Re: Fw: [Bugme-new] [Bug 8104] New: kernel floods console with "connect-debounce failed"

Cristian Mammoli <[email protected]>
Newsgroups gmane.linux.usb.devel
Message-ID <[email protected]>
On lun, 2007-03-05 at 11:28 +0100, Oliver Neukum wrote:

> please try unloading and reloading the ehci driver.
> 
> 	Regards
> 		Oliver

When the device is working:

on rmmod:
[ 5873.059133] ehci_hcd 0000:00:1d.7: remove, state 4
[ 5873.059143] ehci_hcd 0000:00:1d.7: roothub graceful disconnect
[ 5873.059151] usb usb1: USB disconnect, address 1
[ 5873.059156] usb usb1: unregistering device
[ 5873.059162] usb usb1: usb_disable_device nuking all URBs
[ 5873.059171] usb usb1: unregistering interface 1-0:1.0
[ 5873.059202] PM: Removing info for No Bus:usbdev1.1_ep81
[ 5873.061906]  usbdev1.1_ep81: ep_device_release called for
usbdev1.1_ep81
[ 5873.061965] PM: Removing info for usb:1-0:1.0
[ 5873.061984] usb 1-0:1.0: uevent
[ 5873.063834] PM: Removing info for No Bus:usbdev1.1
[ 5873.067939] PM: Removing info for No Bus:usbdev1.1_ep00
[ 5873.068500]  usbdev1.1_ep00: ep_device_release called for
usbdev1.1_ep00
[ 5873.068590] PM: Removing info for usb:usb1
[ 5873.068605] usb usb1: uevent
[ 5873.069125] ehci_hcd 0000:00:1d.7: stop
[ 5873.069137] ehci_hcd 0000:00:1d.7: reset command 010002 (park)=0
ithresh=1 period=1024 Reset HALT
[ 5873.073045] ehci_hcd 0000:00:1d.7: irq normal 0 err 0 reclaim 0 (lost
0)
[ 5873.073054] ehci_hcd 0000:00:1d.7: complete 0 unlink 0
[ 5873.073062] ehci_hcd 0000:00:1d.7: ehci_stop completed status 1000
Halt
[ 5873.073074] ehci_hcd 0000:00:1d.7: USB bus 1 deregistered
[ 5873.073676] ACPI: PCI interrupt for device 0000:00:1d.7 disabled

on modprobe:
[ 5893.958827] ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
[ 5893.959442] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 19
[ 5893.959468] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 5893.959477] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 5893.960134] drivers/usb/core/inode.c: creating file '001'
[ 5893.960147] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 1
[ 5893.960161] ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1
cc=4 pcc=2 ordered !ppc ports=8
[ 5893.960170] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7
uframes 1024 64 bit addr
[ 5893.960223] ehci_hcd 0000:00:1d.7: debug port 1
[ 5893.960232] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 5893.960238] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[ 5893.960253] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xdc444000
[ 5893.960263] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
ithresh=8 period=1024 Reset HALT
[ 5893.964161] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0
ithresh=1 period=1024 RUN
[ 5893.964172] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 5893.964204] usb usb1: default language 0x0409
[ 5893.964222] usb usb1: new device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5893.964227] usb usb1: Product: EHCI Host Controller
[ 5893.964233] usb usb1: Manufacturer: Linux 2.6.21-rc2 ehci_hcd
[ 5893.964238] usb usb1: SerialNumber: 0000:00:1d.7
[ 5893.964255] PM: Adding info for usb:usb1
[ 5893.964277] usb usb1: uevent
[ 5893.964830] usb usb1: usb_probe_device
[ 5893.964887] PM: Adding info for No Bus:usbdev1.1_ep00
[ 5893.965140] usb usb1: configuration #1 chosen from 1 choice
[ 5893.965155] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 5893.965169] PM: Adding info for usb:1-0:1.0
[ 5893.965190] usb 1-0:1.0: uevent
[ 5893.965415] hub 1-0:1.0: usb_probe_interface
[ 5893.965421] hub 1-0:1.0: usb_probe_interface - got id
[ 5893.965427] hub 1-0:1.0: USB hub found
[ 5893.965441] hub 1-0:1.0: 8 ports detected
[ 5893.965446] hub 1-0:1.0: standalone hub
[ 5893.965450] hub 1-0:1.0: no power switching (usb 1.0)
[ 5893.965455] hub 1-0:1.0: individual port over-current protection
[ 5893.965460] hub 1-0:1.0: Single TT
[ 5893.965465] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[ 5893.965472] hub 1-0:1.0: power on to power good time: 20ms
[ 5893.965481] hub 1-0:1.0: local power source is good
[ 5893.965487] hub 1-0:1.0: trying to enable port power on
non-switchable hub
[ 5893.967323] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.967336] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.969303] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.970302] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.971301] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.971313] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.972300] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.973301] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.974295] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.975293] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.975299] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.976299] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.977299] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.978291] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.978296] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.979291] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.980290] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.981289] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.981294] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.982289] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.983287] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.984289] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.984295] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.985286] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.986286] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.987288] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.987292] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.988287] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.989286] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.990284] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.990288] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.991283] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.992283] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.993283] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.993289] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.994283] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.995282] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.996282] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.996288] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.997286] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.998280] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.999279] usb 4-2: uhci_result_common: failed with status 440000
[ 5893.999285] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.000279] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.001279] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.002277] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.002282] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.003277] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.004276] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.005276] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.005281] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.006275] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.007278] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.007886] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.007891] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.007917] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 5894.007932] uhci_hcd 0000:00:1d.2: port 2 portsc 008a,00
[ 5894.007944] hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
[ 5894.007947] usb 4-2: USB disconnect, address 5
[ 5894.007949] usb 4-2: unregistering device
[ 5894.007952] usb 4-2: usb_disable_device nuking all URBs
[ 5894.007960] uhci_hcd 0000:00:1d.2: shutdown urb dfb387d4 pipe
40408580 ep1in-intr
[ 5894.008275] uhci_hcd 0000:00:1d.2: release dev 5 ep81-INT, period 1,
phase 0, 23 us
[ 5894.008280] usb 4-2: uhci_result_common: failed with status 440000
[ 5894.009279] uhci_hcd 0000:00:1d.2: shutdown urb dfc57a14 pipe
00418580 ep3in-iso
[ 5894.009285] uhci_hcd 0000:00:1d.2: shutdown urb dff3d414 pipe
00418580 ep3in-iso
[ 5894.010278] uhci_hcd 0000:00:1d.2: release dev 5 ep83-ISO, period 1,
phase 0, 22 us
[ 5894.010284] usb 4-2: unregistering interface 4-2:1.0
[ 5894.010308] PM: Removing info for No Bus:usbdev4.5_ep81
[ 5894.010335]  usbdev4.5_ep81: ep_device_release called for
usbdev4.5_ep81
[ 5894.010353] PM: Removing info for No Bus:usbdev4.5_ep02
[ 5894.010368]  usbdev4.5_ep02: ep_device_release called for
usbdev4.5_ep02
[ 5894.010382] PM: Removing info for No Bus:usbdev4.5_ep82
[ 5894.010397]  usbdev4.5_ep82: ep_device_release called for
usbdev4.5_ep82
[ 5894.010447] PM: Removing info for No Bus:hci0
[ 5894.068044] PM: Adding info for No Bus:usbdev1.1_ep81
[ 5894.068086] PM: Adding info for No Bus:usbdev1.1
[ 5894.068100] drivers/usb/core/inode.c: creating file '001'
[ 5894.219935] PM: Removing info for usb:4-2:1.0
[ 5894.219973] usb 4-2:1.0: uevent
[ 5894.220005] usb 4-2: unregistering interface 4-2:1.1
[ 5894.220039] PM: Removing info for No Bus:usbdev4.5_ep03
[ 5894.220072]  usbdev4.5_ep03: ep_device_release called for
usbdev4.5_ep03
[ 5894.220100] PM: Removing info for No Bus:usbdev4.5_ep83
[ 5894.220128]  usbdev4.5_ep83: ep_device_release called for
usbdev4.5_ep83
[ 5894.220166] PM: Removing info for usb:4-2:1.1
[ 5894.220179] usb 4-2:1.1: uevent
[ 5894.220244] PM: Removing info for No Bus:usbdev4.5
[ 5894.220300] PM: Removing info for No Bus:usbdev4.5_ep00
[ 5894.220328]  usbdev4.5_ep00: ep_device_release called for
usbdev4.5_ep00
[ 5894.220401] PM: Removing info for usb:4-2
[ 5894.220413] usb 4-2: uevent
[ 5894.298676] hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms
status 0x100
[ 5894.298692] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0040
[ 5894.298726] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5894.298740] hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
[ 5894.364348] hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms
status 0x501
[ 5894.388509] ehci_hcd 0000:00:1d.7: port 6 full speed --> companion
[ 5894.388524] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 003801
POWER OWNER sig=j CONNECT
[ 5894.388535] hub 1-0:1.0: port 6 not reset yet, waiting 50ms
[ 5894.408846] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 003002
POWER OWNER sig=se0 CSC
[ 5894.408896] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0040
[ 5894.450864] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 5894.450887] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5894.450901] hub 4-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 5894.486606] hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms
status 0x101
[ 5894.518845] usb 4-2: new full speed USB device using uhci_hcd and
address 6
[ 5894.635443] usb 4-2: new device strings: Mfr=0, Product=0,
SerialNumber=0
[ 5894.635478] PM: Adding info for usb:4-2
[ 5894.635504] usb 4-2: uevent
[ 5894.635533] usb 4-2: usb_probe_device
[ 5894.635583] PM: Adding info for No Bus:usbdev4.6_ep00
[ 5894.635620] usb 4-2: configuration #1 chosen from 1 choice
[ 5894.638405] usb 4-2: adding 4-2:1.0 (config #1, interface 0)
[ 5894.638429] PM: Adding info for usb:4-2:1.0
[ 5894.638452] usb 4-2:1.0: uevent
[ 5894.638484] hci_usb 4-2:1.0: usb_probe_interface
[ 5894.638490] hci_usb 4-2:1.0: usb_probe_interface - got id
[ 5894.640420] PM: Adding info for No Bus:hci0
[ 5894.640497] PM: Adding info for No Bus:usbdev4.6_ep81
[ 5894.640546] PM: Adding info for No Bus:usbdev4.6_ep02
[ 5894.640596] PM: Adding info for No Bus:usbdev4.6_ep82
[ 5894.640631] usb 4-2: adding 4-2:1.1 (config #1, interface 1)
[ 5894.640644] PM: Adding info for usb:4-2:1.1
[ 5894.640664] usb 4-2:1.1: uevent
[ 5894.640712] PM: Adding info for No Bus:usbdev4.6_ep03
[ 5894.640765] PM: Adding info for No Bus:usbdev4.6_ep83
[ 5894.640816] PM: Adding info for No Bus:usbdev4.6
[ 5894.640842] drivers/usb/core/inode.c: creating file '006'
[ 5894.644334] uhci_hcd 0000:00:1d.2: reserve dev 6 ep81-INT, period 1,
phase 0, 23 us
[ 5894.644364] uhci_hcd 0000:00:1d.2: reserve dev 6 ep83-ISO, period 1,
phase 0, 22 us
[ 5895.409272] hub 1-0:1.0: hub_suspend
[ 5895.409291] ehci_hcd 0000:00:1d.7: suspend root hub
[ 5895.409326] usb usb1: usb auto-suspend

When the device is NOT working:
on rmmod:
[ 5956.605038] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001002
POWER sig=se0 CSC
[ 5956.606976] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5956.611471] ehci_hcd 0000:00:1d.7: remove, state 1
[ 5956.611480] ehci_hcd 0000:00:1d.7: roothub graceful disconnect
[ 5956.612159] usb usb1: USB disconnect, address 1
[ 5956.617042] hub 1-0:1.0: hub_port_status failed (err = -19)
[ 5956.617053] hub 1-0:1.0: connect-debounce failed, port 6 disabled
[ 5956.617061] hub 1-0:1.0: cannot disable port 6 (err = -19)
[ 5956.617072] hub 1-0:1.0: state 0 ports 8 chg 0000 evt 0040
[ 5956.617207] usb usb1: unregistering device
[ 5956.617213] usb usb1: usb_disable_device nuking all URBs
[ 5956.617273] usb usb1: unregistering interface 1-0:1.0
[ 5956.617796] PM: Removing info for No Bus:usbdev1.1_ep81
[ 5956.619317]  usbdev1.1_ep81: ep_device_release called for
usbdev1.1_ep81
[ 5956.619649] PM: Removing info for usb:1-0:1.0
[ 5956.619856] usb 1-0:1.0: uevent
[ 5956.620063] PM: Removing info for No Bus:usbdev1.1
[ 5956.620323] PM: Removing info for No Bus:usbdev1.1_ep00
[ 5956.620574]  usbdev1.1_ep00: ep_device_release called for
usbdev1.1_ep00
[ 5956.629199] PM: Removing info for usb:usb1
[ 5956.630008] usb usb1: uevent
[ 5956.630312] ehci_hcd 0000:00:1d.7: stop
[ 5956.630330] ehci_hcd 0000:00:1d.7: reset command 010003 (park)=0
ithresh=1 period=1024 Reset RUN
[ 5956.630398] hub 4-0:1.0: state 8 ports 2 chg 0000 evt 0000
[ 5956.630409] usb usb4: usb auto-resume
[ 5956.630413] usb usb4: finish resume
[ 5956.630426] hub 4-0:1.0: hub_resume
[ 5956.630431] usb usb4: wakeup_rh
[ 5956.636411] ehci_hcd 0000:00:1d.7: irq normal 0 err 0 reclaim 0 (lost
0)
[ 5956.636418] ehci_hcd 0000:00:1d.7: complete 0 unlink 0
[ 5956.636427] ehci_hcd 0000:00:1d.7: ehci_stop completed status 1000
Halt
[ 5956.636439] ehci_hcd 0000:00:1d.7: USB bus 1 deregistered
[ 5956.637657] ACPI: PCI interrupt for device 0000:00:1d.7 disabled
[ 5956.659177] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.659195] hub 4-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 5956.663402] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.670761] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.674488] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.677960] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.681442] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.692156] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.696040] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.699525] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5956.703081] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.706515] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.709946] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.715352] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.731839] uhci_hcd 0000:00:1d.2: port 2 portsc 0083,00
[ 5956.737799] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.743301] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5956.761068] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.770317] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.780202] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.793564] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.799309] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5956.804861] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.810720] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.816027] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.825327] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.837464] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5956.846061] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.856714] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.870974] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.876415] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.881731] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5956.891037] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.900627] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.906022] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.911815] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.924553] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5956.933444] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.939226] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.948203] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.953422] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5956.975736] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5957.007689] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.039648] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.054566] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.058804] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.063961] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.072492] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.081037] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.088968] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.093994] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.099558] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.109616] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.119231] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.127036] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.132342] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.137663] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.143455] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.152273] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.168561] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.168584] hub 4-0:1.0: debounce: port 2: total 1500ms stable 0ms
status 0x101
[ 5957.168590] hub 4-0:1.0: connect-debounce failed, port 2 disabled
[ 5957.168608] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 5957.193671] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 5957.193693] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5957.193707] hub 4-0:1.0: port 2, status 0100, change 0001, 12 Mb/s
[ 5957.202877] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5957.208461] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
 [many more lines]

on modprobe:

[ 5999.188205] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5999.197761] uhci_hcd 0000:00:1d.2: port 2 portsc 0093,00
[ 5999.212286] ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
[ 5999.213921] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 19
[ 5999.214448] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 5999.214457] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 5999.215277] drivers/usb/core/inode.c: creating file '001'
[ 5999.215667] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 1
[ 5999.216144] ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1
cc=4 pcc=2 ordered !ppc ports=8
[ 5999.216156] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7
uframes 1024 64 bit addr
[ 5999.217785] ehci_hcd 0000:00:1d.7: debug port 1
[ 5999.217799] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 5999.217806] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[ 5999.217821] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xdc444000
[ 5999.217832] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
ithresh=8 period=1024 Reset HALT
[ 5999.221711] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0
ithresh=1 period=1024 RUN
[ 5999.221728] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 5999.221763] usb usb1: default language 0x0409
[ 5999.221781] usb usb1: new device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5999.221787] usb usb1: Product: EHCI Host Controller
[ 5999.221792] usb usb1: Manufacturer: Linux 2.6.21-rc2 ehci_hcd
[ 5999.221798] usb usb1: SerialNumber: 0000:00:1d.7
[ 5999.221816] PM: Adding info for usb:usb1
[ 5999.221839] usb usb1: uevent
[ 5999.223305] usb usb1: usb_probe_device
[ 5999.223362] PM: Adding info for No Bus:usbdev1.1_ep00
[ 5999.223908] usb usb1: configuration #1 chosen from 1 choice
[ 5999.223925] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 5999.223938] PM: Adding info for usb:1-0:1.0
[ 5999.223957] usb 1-0:1.0: uevent
[ 5999.224507] hub 1-0:1.0: usb_probe_interface
[ 5999.224513] hub 1-0:1.0: usb_probe_interface - got id
[ 5999.224520] hub 1-0:1.0: USB hub found
[ 5999.224534] hub 1-0:1.0: 8 ports detected
[ 5999.224538] hub 1-0:1.0: standalone hub
[ 5999.224544] hub 1-0:1.0: no power switching (usb 1.0)
[ 5999.224549] hub 1-0:1.0: individual port over-current protection
[ 5999.224555] hub 1-0:1.0: Single TT
[ 5999.224561] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
[ 5999.224567] hub 1-0:1.0: power on to power good time: 20ms
[ 5999.224582] hub 1-0:1.0: local power source is good
[ 5999.224588] hub 1-0:1.0: trying to enable port power on
non-switchable hub
[ 5999.229739] uhci_hcd 0000:00:1d.2: port 2 portsc 0082,00
[ 5999.325205] PM: Adding info for No Bus:usbdev1.1_ep81
[ 5999.325904] PM: Adding info for No Bus:usbdev1.1
[ 5999.326055] drivers/usb/core/inode.c: creating file '001'
[ 5999.357054] hub 4-0:1.0: debounce: port 2: total 1250ms stable 100ms
status 0x100
[ 5999.357064] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 5999.357076] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0040
[ 5999.357098] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.357107] hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
[ 5999.369962] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.376666] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001002
POWER sig=se0 CSC
[ 5999.380818] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.399452] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.403801] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.408386] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.414546] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001002
POWER sig=se0 CSC
[ 5999.420914] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.427753] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.434617] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.441911] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.454517] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001002
POWER sig=se0 CSC
[ 5999.461407] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.473717] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.489035] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.496186] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.502728] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001002
POWER sig=se0 CSC
[ 5999.509232] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.515620] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.522366] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.529590] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.538937] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001002
POWER sig=se0 CSC
[ 5999.545027] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.551644] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.562029] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.568345] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.574443] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.605860] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.629855] usb usb4: suspend_rh (auto-stop)
[ 5999.637854] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.669810] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.677466] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.683446] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.686641] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.694235] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.698202] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001002
POWER sig=se0 CSC
[ 5999.708509] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.727479] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.735054] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.742765] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.751978] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.759329] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.770328] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.787838] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.796368] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.800848] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.808632] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.823582] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.830804] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.835923] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.841296] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.845015] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT
[ 5999.852711] ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803
POWER sig=j CSC CONNECT



-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.