[PATCH 15/23] USB: RTS/DTR signal patch for airprime driver

From: Martin Schiller <[email protected]>

I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:

Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem.  Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.

With the attached patch, the RTS/DTR lines are resetted on a close.  The
code was mainly taken from the option.c driver.
---
 drivers/usb/serial/airprime.c |   47 +++++++++++++++++++++++++++++++++++++++++
 1 files changed, 47 insertions(+), 0 deletions(-)

diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c
index 18816bf..310a8b5 100644
--- a/drivers/usb/serial/airprime.c
+++ b/drivers/usb/serial/airprime.c
@@ -44,8 +44,43 @@ struct airprime_private {
 	int outstanding_urbs;
 	int throttled;
 	struct urb *read_urbp[NUM_READ_URBS];
+
+	/* Settings for the port */
+	int rts_state;	/* Handshaking pins (outputs) */
+	int dtr_state;
+	int cts_state;	/* Handshaking pins (inputs) */
+	int dsr_state;
+	int dcd_state;
+	int ri_state;
 };
 
+static int airprime_send_setup(struct usb_serial_port *port)
+{
+	struct usb_serial *serial = port->serial;
+	struct airprime_private *priv;
+
+	dbg("%s", __FUNCTION__);
+
+	if (port->number != 0)
+		return 0;
+
+	priv = usb_get_serial_port_data(port);
+
+	if (port->tty) {
+		int val = 0;
+		if (priv->dtr_state)
+			val |= 0x01;
+		if (priv->rts_state)
+			val |= 0x02;
+
+		return usb_control_msg(serial->dev,
+				usb_rcvctrlpipe(serial->dev, 0),
+				0x22,0x21,val,0,NULL,0,USB_CTRL_SET_TIMEOUT);
+	}
+
+	return 0;
+}
+
 static void airprime_read_bulk_callback(struct urb *urb)
 {
 	struct usb_serial_port *port = urb->context;
@@ -118,6 +153,10 @@ static int airprime_open(struct usb_serial_port *port, struct file *filp)
 		usb_set_serial_port_data(port, priv);
 	}
 
+	/* Set some sane defaults */
+	priv->rts_state = 1;
+	priv->dtr_state = 1;
+
 	for (i = 0; i < NUM_READ_URBS; ++i) {
 		buffer = kmalloc(buffer_size, GFP_KERNEL);
 		if (!buffer) {
@@ -151,6 +190,9 @@ static int airprime_open(struct usb_serial_port *port, struct file *filp)
 		/* remember this urb so we can kill it when the port is closed */
 		priv->read_urbp[i] = urb;
 	}
+
+	airprime_send_setup(port);
+
 	goto out;
 
  errout:
@@ -176,6 +218,11 @@ static void airprime_close(struct usb_serial_port *port, struct file * filp)
 
 	dbg("%s - port %d", __FUNCTION__, port->number);
 
+	priv->rts_state = 0;
+	priv->dtr_state = 0;
+
+	airprime_send_setup(port);
+
 	for (i = 0; i < NUM_READ_URBS; ++i) {
 		usb_kill_urb (priv->read_urbp[i]);
 		kfree (priv->read_urbp[i]->transfer_buffer);
-- 
1.5.0.2


-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel