Info files: USB Lan device, kaweth failure in Linux
Roger Adair <[email protected]>
| Newsgroups | gmane.linux.usb.devel |
|---|---|
| Message-ID | <[email protected]> |
Hi again,
As requested some data on the Xircom problem. Note that I had a 1 gig
SanDisk plugged in during the test for the "bad" version 2.6.15-7.
I really than you Greg and Oliver for your interest and anyone else who
has taken a look at my earlier msg: "USB Lan device, kaweth failure..."
Dmesg Old Mepis2.6.10 sets up the USB:
Linux version 2.6.10 (root@mepis-msi) (gcc version 3.3.5 (Debian
1:3.3.5-8)) #1 Wed Feb 23 16:54:53 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003dff0000 (usable)
BIOS-e820: 000000003dff0000 - 000000003dff3000 (ACPI NVS)
BIOS-e820: 000000003dff3000 - 000000003e000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
95MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f4580
On node 0 totalpages: 253936
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 24560 pages, LIFO batch:5
DMI 2.2 present.
ACPI: RSDP (v000 KM400 ) @ 0x000f6020
ACPI: RSDT (v001 KM400 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3dff3000
ACPI: FADT (v001 KM400 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3dff3040
ACPI: MADT (v001 KM400 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3dff7fc0
ACPI: DSDT (v001 KM400 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Built 1 zonelists
Kernel command line: root=/dev/hda8 nomce quiet splash=verbose vga=791
bootsplash: verbose mode.
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2001.003 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1002128k/1015744k available (2660k kernel code, 12908k reserved,
864k data, 200k init, 98240k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3956.73 BogoMIPS (lpj=1978368)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
CPU: AMD Athlon(tm) XP 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0a20)
checking if image is initramfs...it isn't (bad gzip magic numbers);
looks like an initrd
Freeing initrd memory: 90k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb240, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050125
spurious 8259A interrupt: IRQ7.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [email protected]
** so I can fix the driver.
audit: initializing netlink socket (disabled)
audit(1176403832.118:0): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
SELinux: Registering netfilter hooks
Initializing Cryptographic API
vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 3072k,
total 32768k
vesafb: mode is 1024x768x16, linelength=2048, pages=20
vesafb: protected mode interface info at c000:7db3
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.4-2004/02/19: looking for picture.... silentjpeg size
46865 bytes, found (1024x768, 46140 bytes, v3).
Console: switching to colour frame buffer device 121x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 11 (level, low) -> IRQ 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: QUANTUM FIREBALLP AS60.0, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: DVD-RW IDE1008, ATAPI CD/DVD-ROM drive
hdd: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 117266688 sectors (60040 MB) w/1902KiB Cache, CHS=65535/16/63,
UDMA(100)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hda3
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 16X DVD-ROM drive, 512kB Cache, UDMA(33)
3ware Storage Controller device driver for Linux v1.26.02.000.
3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
libata version 1.10 loaded.
ieee1394: Initialized config rom entry `ip1394'
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: irq 10, pci mem 0xe8001000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: GenPS/2 Genius Wheel Mouse on isa0060/serio1
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 15
ACPI wakeup devices:
SLPB PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 LAN0 UAR1 ECP1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: Couldn't find valid RAM disk image starting at 0.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 200k freed
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: irq 11, io base 0xd400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: irq 11, io base 0xd800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: irq 10, io base 0xdc00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
inserting floppy driver for 2.6.10
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ibm_acpi: ec object not found
usb 2-2: new full speed USB device using uhci_hcd and address 2
ACPI: Thermal Zone [THRM] (49 C)
drivers/usb/net/kaweth.c: Firmware present in device.
drivers/usb/net/kaweth.c: Statistics collection: 0
drivers/usb/net/kaweth.c: Multicast filter limit: 80
drivers/usb/net/kaweth.c: MTU: 1514
drivers/usb/net/kaweth.c: Read MAC address 00:10:a4:a6:21:2b
drivers/usb/net/kaweth.c: kaweth interface created at eth0
usbcore: registered new driver kaweth
powernow-k8: Processor cpuid 681 not supported
cpufreq: No nForce2 chipset.
Adding 594364k swap on /dev/hda10. Priority:1 extents:1
EXT3 FS on hda8, internal journal
ndiswrapper version 1.1 loaded (preempt=yes,smp=no)
usbcore: registered new driver ndiswrapper
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
eth1: VIA Rhine II at 0xe8002000, 00:50:2c:a1:e3:0a, IRQ 11.
eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
usb 2-2: cat timed out on ep0in
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
NTFS driver 2.1.22 [Flags: R/W MODULE].
NTFS volume version 3.1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda7.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda7.
NTFS-fs error (device hda7): read_ntfs_boot_sector(): Primary boot
sector is invalid.
NTFS-fs error (device hda7): read_ntfs_boot_sector(): Mount option
errors=recover not used. Aborting without trying to recover.
NTFS-fs error (device hda7): ntfs_fill_super(): Not an NTFS volume.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda9.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda9.
NTFS-fs error (device hda9): read_ntfs_boot_sector(): Primary boot
sector is invalid.
NTFS-fs error (device hda9): read_ntfs_boot_sector(): Mount option
errors=recover not used. Aborting without trying to recover.
NTFS-fs error (device hda9): ntfs_fill_super(): Not an NTFS volume.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
NET: Registered protocol family 17
drivers/usb/net/kaweth.c: Failed to set Rx mode: -16
drivers/usb/net/kaweth.c: Failed to set Rx mode: -71
eth1: link down
drivers/usb/net/kaweth.c: Failed to set Rx mode: -16
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0420c40(lo)
IPv6 over IPv4 tunneling driver
drivers/usb/net/kaweth.c: Failed to set Rx mode: -16
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (7935 buckets, 63480 max) - 300 bytes per conntrack
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda1.
NTFS volume version 3.1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda7.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda7.
NTFS-fs error (device hda7): read_ntfs_boot_sector(): Primary boot
sector is invalid.
NTFS-fs error (device hda7): read_ntfs_boot_sector(): Mount option
errors=recover not used. Aborting without trying to recover.
NTFS-fs error (device hda7): ntfs_fill_super(): Not an NTFS volume.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda9.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev hda9.
NTFS-fs error (device hda9): read_ntfs_boot_sector(): Primary boot
sector is invalid.
NTFS-fs error (device hda9): read_ntfs_boot_sector(): Mount option
errors=recover not used. Aborting without trying to recover.
NTFS-fs error (device hda9): ntfs_fill_super(): Not an NTFS volume.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
eth0: no IPv6 routers present
eth1: no IPv6 routers present
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
usb 2-2: usbfs: USBDEVFS_CONTROL failed cmd lsusb rqt 128 rq 6 len 255
ret -71
======================end dmesg 2.6.10==================
Dmesg New Mepis2.6.15-27 Does not set up the Xircom USB Lan:
[17179569.184000] Linux version 2.6.15-27-desktop (root@mepis-pro) (gcc
version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Sun Mar 11 21:36:14
EDT 2007
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000003dff0000 (usable)
[17179569.184000] BIOS-e820: 000000003dff0000 - 000000003dff3000 (ACPI NVS)
[17179569.184000] BIOS-e820: 000000003dff3000 - 000000003e000000 (ACPI
data)
[17179569.184000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[17179569.184000] 95MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f4580
[17179569.184000] On node 0 totalpages: 253936
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000] Normal zone: 225280 pages, LIFO batch:31
[17179569.184000] HighMem zone: 24560 pages, LIFO batch:3
[17179569.184000] DMI 2.2 present.
[17179569.184000] ACPI: RSDP (v000 KM400
) @ 0x000f6020
[17179569.184000] ACPI: RSDT (v001 KM400 AWRDACPI 0x42302e31 AWRD
0x00000000) @ 0x3dff3000
[17179569.184000] ACPI: FADT (v001 KM400 AWRDACPI 0x42302e31 AWRD
0x00000000) @ 0x3dff3040
[17179569.184000] ACPI: MADT (v001 KM400 AWRDACPI 0x42302e31 AWRD
0x00000000) @ 0x3dff7fc0
[17179569.184000] ACPI: DSDT (v001 KM400 AWRDACPI 0x00001000 MSFT
0x0100000e) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x4008
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 6:8 APIC version 16
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000,
GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 40000000 (gap:
3e000000:c0c00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: us init=/etc/init apm=power-off
vga=791 quiet xres=1280x1024
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[17179569.184000] Detected 2000.625 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour dummy device 80x25
[17179572.572000] Dentry cache hash table entries: 131072 (order: 7,
524288 bytes)
[17179572.572000] Inode-cache hash table entries: 65536 (order: 6,
262144 bytes)
[17179572.608000] Memory: 1000472k/1015744k available (2741k kernel
code, 14600k reserved, 931k data, 192k init, 98240k highmem)
[17179572.608000] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[17179572.688000] Calibrating delay using timer specific routine..
4005.16 BogoMIPS (lpj=8010330)
[17179572.688000] Security Framework v1.0.0 initialized
[17179572.688000] SELinux: Disabled at boot.
[17179572.688000] Capability LSM initialized
[17179572.688000] Mount-cache hash table entries: 512
[17179572.688000] CPU: After generic identify, caps: 0383fbff c1c3fbff
00000000 00000000 00000000 00000000 00000000
[17179572.688000] CPU: After vendor identify, caps: 0383fbff c1c3fbff
00000000 00000000 00000000 00000000 00000000
[17179572.688000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[17179572.688000] CPU: L2 Cache: 256K (64 bytes/line)
[17179572.688000] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000
00000420 00000000 00000000 00000000
[17179572.688000] Intel machine check architecture supported.
[17179572.688000] Intel machine check reporting enabled on CPU#0.
[17179572.688000] mtrr: v2.0 (20020519)
[17179572.688000] CPU: AMD Athlon(tm) XP 2400+ stepping 01
[17179572.688000] Enabling fast FPU save and restore... done.
[17179572.688000] Enabling unmasked SIMD FPU exception support... done.
[17179572.688000] Checking 'hlt' instruction... OK.
[17179572.704000] checking if image is initramfs...it isn't (no cpio
magic); looks like an initrd
[17179572.816000] Freeing initrd memory: 1491k freed
[17179572.820000] ACPI: Looking for DSDT ... not found!
[17179572.824000] ENABLING IO-APIC IRQs
[17179572.824000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179572.968000] NET: Registered protocol family 16
[17179572.968000] ACPI: bus type pci registered
[17179572.968000] PCI: PCI BIOS revision 2.10 entry at 0xfb240, last bus=1
[17179572.968000] PCI: Using configuration type 1
[17179572.968000] ACPI: Subsystem revision 20051216
[17179572.976000] ACPI: Interpreter enabled
[17179572.976000] ACPI: Using IOAPIC for interrupt routing
[17179572.976000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179572.976000] PCI: Probing PCI hardware (bus 00)
[17179572.976000] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[17179572.980000] PCI quirk: region 4000-407f claimed by vt8235 PM
[17179572.980000] PCI quirk: region 5000-500f claimed by vt8235 SMB
[17179572.980000] Boot video device is 0000:01:00.0
[17179572.980000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179573.016000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12)
[17179573.016000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
[17179573.016000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5
[17179573.016000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5
[17179573.016000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11
12) *0, disabled.
[17179573.016000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11
12) *0, disabled.
[17179573.016000] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11
12) *0, disabled.
[17179573.016000] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11
12) *0, disabled.
[17179573.020000] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
[17179573.020000] ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
[17179573.020000] ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
[17179573.020000] ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
[17179573.024000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179573.024000] pnp: PnP ACPI init
[17179573.028000] pnp: PnP ACPI: found 15 devices
[17179573.028000] PnPBIOS: Disabled by ACPI PNP
[17179573.028000] SCSI subsystem initialized
[17179573.028000] usbcore: registered new driver usbfs
[17179573.028000] usbcore: registered new driver hub
[17179573.028000] PCI: Using ACPI for IRQ routing
[17179573.028000] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[17179573.056000] pnp: 00:01: ioport range 0x4000-0x407f could not be
reserved
[17179573.056000] pnp: 00:01: ioport range 0x5000-0x500f has been reserved
[17179573.056000] PCI: Bridge: 0000:00:01.0
[17179573.056000] IO window: disabled.
[17179573.056000] MEM window: e6000000-e7ffffff
[17179573.056000] PREFETCH window: e0000000-e3ffffff
[17179573.056000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[17179573.056000] Machine check exception polling timer started.
[17179573.060000] audit: initializing netlink socket (disabled)
[17179573.060000] audit(1176402106.060:1): initialized
[17179573.060000] highmem bounce pool size: 64 pages
[17179573.060000] VFS: Disk quotas dquot_6.5.1
[17179573.060000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179573.060000] squashfs: version 3.1 (2006/08/15) Phillip Lougher
[17179573.060000] NTFS driver 2.1.25 [Flags: R/W].
[17179573.060000] JFS: nTxBlock = 7830, nTxLock = 62640
[17179573.068000] Registering unionfs 1.1.2
[17179573.068000] Initializing Cryptographic API
[17179573.068000] io scheduler noop registered
[17179573.068000] io scheduler anticipatory registered
[17179573.068000] io scheduler deadline registered
[17179573.068000] io scheduler cfq registered
[17179573.068000] vesafb: framebuffer at 0xe0000000, mapped to
0xf8d00000, using 3072k, total 32768k
[17179573.068000] vesafb: mode is 1024x768x16, linelength=2048, pages=20
[17179573.068000] vesafb: protected mode interface info at c000:7db3
[17179573.068000] vesafb: scrolling: redraw
[17179573.068000] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[17179573.068000] vesafb: Mode is VGA compatible
[17179573.152000] Console: switching to colour frame buffer device 128x48
[17179573.152000] fb0: VESA VGA frame buffer device
[17179573.152000] isapnp: Scanning for PnP cards...
[17179573.464000] isapnp: No Plug & Play device found
[17179573.476000] Non-volatile memory driver v1.2
[17179573.476000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[17179573.480000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179573.480000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179573.480000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports,
IRQ sharing enabled
[17179573.480000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179573.480000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179573.480000] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179573.480000] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179573.480000] RAMDISK driver initialized: 16 RAM disks of 65536K
size 1024 blocksize
[17179573.480000] loop: loaded (max 8 devices)
[17179573.480000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179573.480000] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[17179573.480000] VP_IDE: IDE controller at PCI slot 0000:00:11.1
[17179573.480000] **** SET: Misaligned resource pointer: dfc94b02 Type
07 Len 0
[17179573.480000] ACPI: PCI Interrupt Link [ALKA] disabled and
referenced, BIOS bug.
[17179573.480000] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0,
using IRQ 20
[17179573.480000] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[17179573.480000] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] ->
GSI 20 (level, low) -> IRQ 16
[17179573.480000] PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 0
[17179573.480000] VP_IDE: chipset revision 6
[17179573.480000] VP_IDE: not 100% native mode: will probe irqs later
[17179573.480000] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on
pci0000:00:11.1
[17179573.480000] ide0: BM-DMA at 0xe000-0xe007, BIOS settings:
hda:DMA, hdb:pio
[17179573.480000] ide1: BM-DMA at 0xe008-0xe00f, BIOS settings:
hdc:DMA, hdd:DMA
[17179573.480000] Probing IDE interface ide0...
[17179573.900000] hda: QUANTUM FIREBALLP AS60.0, ATA DISK drive
[17179574.572000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179574.572000] Probing IDE interface ide1...
[17179575.436000] hdc: DVD-RW IDE1008, ATAPI CD/DVD-ROM drive
[17179576.220000] hdd: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
[17179576.276000] ide1 at 0x170-0x177,0x376 on irq 15
[17179576.276000] hda: max request size: 128KiB
[17179576.280000] hda: 117266688 sectors (60040 MB) w/1902KiB Cache,
CHS=65535/16/63, UDMA(100)
[17179576.280000] hda: cache flushes not supported
[17179576.280000] hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hda3
[17179576.352000] hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[17179576.352000] Uniform CD-ROM driver Revision: 3.20
[17179576.368000] hdd: ATAPI 16X DVD-ROM drive, 512kB Cache, UDMA(33)
[17179576.372000] ACPI: bus type scsi registered
[17179576.372000] libata version 1.20 loaded.
[17179576.372000] Driver 'sd' needs updating - please use bus_type methods
[17179576.372000] ieee1394: Initialized config rom entry `ip1394'
[17179576.372000] ieee1394: raw1394: /dev/raw1394 device initialized
[17179576.372000] sbp2: $Rev: 1306 $ Ben Collins <[email protected]>
[17179576.372000] ieee1394: sbp2: Driver forced to serialize I/O
(serialize_io=1)
[17179576.372000] ieee1394: sbp2: Try serialize_io=0 for better performance
[17179576.372000] usbmon: debugfs is not available
[17179576.372000] **** SET: Misaligned resource pointer: dfcb3922 Type
07 Len 0
[17179576.372000] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[17179576.372000] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKB] ->
GSI 21 (level, low) -> IRQ 17
[17179576.372000] PCI: Via IRQ fixup for 0000:00:10.3, from 5 to 1
[17179576.372000] ehci_hcd 0000:00:10.3: EHCI Host Controller
[17179576.372000] ehci_hcd 0000:00:10.3: new USB bus registered,
assigned bus number 1
[17179576.372000] ehci_hcd 0000:00:10.3: irq 17, io mem 0xe8001000
[17179576.372000] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[17179576.372000] hub 1-0:1.0: USB hub found
[17179576.372000] hub 1-0:1.0: 6 ports detected
[17179576.476000] Initializing USB Mass Storage driver...
[17179576.660000] usbcore: registered new driver usb-storage
[17179576.660000] USB Mass Storage support registered.
[17179576.660000] mice: PS/2 mouse device common for all mice
[17179576.660000] NET: Registered protocol family 2
[17179576.680000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179576.700000] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[17179576.700000] TCP established hash table entries: 131072 (order: 7,
524288 bytes)
[17179576.700000] TCP bind hash table entries: 65536 (order: 6, 262144
bytes)
[17179576.700000] TCP: Hash tables configured (established 131072 bind
65536)
[17179576.700000] TCP reno registered
[17179576.700000] ip_tables: (C) 2000-2002 Netfilter core team
[17179576.736000] TCP bic registered
[17179576.736000] NET: Registered protocol family 1
[17179576.736000] NET: Registered protocol family 8
[17179576.736000] NET: Registered protocol family 20
[17179576.736000] Using IPI Shortcut mode
[17179576.736000] ACPI wakeup devices:
[17179576.736000] SLPB PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 LAN0 UAR1
ECP1
[17179576.736000] ACPI: (supports S0 S1 S4 S5)
[17179576.736000] RAMDISK: Compressed image found at block 0
[17179576.872000] EXT2-fs warning: maximal mount count reached, running
e2fsck is recommended
[17179576.872000] VFS: Mounted root (ext2 filesystem).
[17179586.924000] Unable to identify CD-ROM format.
[17179586.928000] VFS: Can't find an ext2 filesystem on dev hda.
[17179586.928000] VFS: Can't find ext3 filesystem on dev hda.
[17179586.928000] ReiserFS: hda: warning: sh-2021: reiserfs_fill_super:
can not find reiserfs on hda
[17179586.928000] FAT: invalid media value (0x06)
[17179586.928000] VFS: Can't find a valid FAT filesystem on dev hda.
[17179586.928000] NTFS-fs warning (device hda): is_boot_sector_ntfs():
Invalid boot sector checksum.
[17179586.928000] NTFS-fs error (device hda): read_ntfs_boot_sector():
Primary boot sector is invalid.
[17179586.928000] NTFS-fs error (device hda): read_ntfs_boot_sector():
Mount option errors=recover not used. Aborting without trying to recover.
[17179586.928000] NTFS-fs error (device hda): ntfs_fill_super(): Not an
NTFS volume.
[17179587.016000] ISO 9660 Extensions: Microsoft Joliet Level 3
[17179587.060000] ISO 9660 Extensions: RRIP_1991A
[17179600.360000] Freeing unused kernel memory: 192k freed
[17179611.456000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179611.488000] shpchp: Standard Hot Plug PCI Controller Driver
version: 0.4
[17179611.584000] Linux agpgart interface v0.101 (c) Dave Jones
[17179611.796000] USB Universal Host Controller Interface driver v2.3
[17179611.796000] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] ->
GSI 21 (level, low) -> IRQ 17
[17179611.796000] PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1
[17179611.796000] uhci_hcd 0000:00:10.0: UHCI Host Controller
[17179611.796000] uhci_hcd 0000:00:10.0: new USB bus registered,
assigned bus number 2
[17179611.796000] uhci_hcd 0000:00:10.0: irq 17, io base 0x0000d400
[17179611.796000] hub 2-0:1.0: USB hub found
[17179611.796000] hub 2-0:1.0: 2 ports detected
[17179611.924000] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [ALKB] ->
GSI 21 (level, low) -> IRQ 17
[17179611.924000] PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 1
[17179611.924000] uhci_hcd 0000:00:10.1: UHCI Host Controller
[17179611.924000] uhci_hcd 0000:00:10.1: new USB bus registered,
assigned bus number 3
[17179611.924000] uhci_hcd 0000:00:10.1: irq 17, io base 0x0000d800
[17179611.924000] hub 3-0:1.0: USB hub found
[17179611.924000] hub 3-0:1.0: 2 ports detected
[17179612.024000] Real Time Clock Driver v1.12
[17179612.060000] ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKB] ->
GSI 21 (level, low) -> IRQ 17
[17179612.060000] PCI: Via IRQ fixup for 0000:00:10.2, from 5 to 1
[17179612.060000] uhci_hcd 0000:00:10.2: UHCI Host Controller
[17179612.064000] uhci_hcd 0000:00:10.2: new USB bus registered,
assigned bus number 4
[17179612.064000] uhci_hcd 0000:00:10.2: irq 17, io base 0x0000dc00
[17179612.064000] hub 4-0:1.0: USB hub found
[17179612.064000] hub 4-0:1.0: 2 ports detected
[17179612.196000] via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by
Donald Becker
[17179612.200000] **** SET: Misaligned resource pointer: f68765c2 Type
07 Len 0
[17179612.200000] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
[17179612.200000] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] ->
GSI 23 (level, low) -> IRQ 18
[17179612.200000] PCI: Via IRQ fixup for 0000:00:12.0, from 11 to 2
[17179612.204000] eth0: VIA Rhine II at 0x1e800, 00:50:2c:a1:e3:0a, IRQ 18.
[17179612.204000] eth0: MII PHY found at address 1, status 0x7849
advertising 05e1 Link 0000.
[17179612.232000] agpgart: Detected VIA KM400/KM400A chipset
[17179612.236000] agpgart: AGP aperture is 32M @ 0xe4000000
[17179612.292000] usb 2-2: new full speed USB device using uhci_hcd and
address 2
[17179612.436000] usb 2-2: can't set config #1, error -71
[17179612.456000] irda_init()
[17179612.456000] NET: Registered protocol family 23
[17179612.548000] usb 2-2: new full speed USB device using uhci_hcd and
address 3
[17179612.576000] input: PC Speaker as /class/input/input1
[17179612.692000] usb 2-2: can't set config #1, error -71
[17179612.716000] Floppy drive(s): fd0 is 1.44M
[17179612.772000] FDC 0 is a post-1991 82077
[17179612.804000] usb 2-2: new full speed USB device using uhci_hcd and
address 4
[17179612.832000] usb 2-2: can't set config #1, error -71
[17179612.944000] usb 2-2: new full speed USB device using uhci_hcd and
address 5
[17179612.972000] usb 2-2: can't set config #1, error -71
[17179613.280000] input: GenPS/2 Genius <NULL> as /class/input/input2
[17179613.788000] parport: PnPBIOS parport detected.
[17179613.788000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
[17179615.400000] lp0: using parport0 (interrupt-driven).
[17179616.200000] eth0: link down
[17179616.892000] **** SET: Misaligned resource pointer: f6bed302 Type
07 Len 0
[17179616.892000] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[17179616.892000] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] ->
GSI 22 (level, low) -> IRQ 19
[17179616.892000] PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 3
[17179616.892000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[17179617.220000] NET: Registered protocol family 17
[17179618.196000] fuse init (API version 7.8)
[17179618.196000] fuse distribution version: 2.6.1
[17179618.536000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179618.536000] md: bitmap version 4.39
[17179618.972000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
[email protected]
[17179622.088000] cdrom: open failed.
[17179624.948000] input: GenPS/2 Genius <NULL> as /class/input/input3
[17179625.460000] powernow-k8: Processor cpuid 681 not supported
[17179628.784000] ndiswrapper version 1.38 loaded (preempt=yes,smp=no)
[17179628.812000] usbcore: registered new driver ndiswrapper
[17179629.504000] Adding 594364k swap on /dev/hda10. Priority:1
extents:1 across:594364k
[17179630.588000] ACPI: Power Button (FF) [PWRF]
[17179630.588000] ACPI: Power Button (CM) [PWRB]
[17179630.588000] ACPI: Sleep Button (CM) [SLPB]
[17179630.660000] ACPI: Fan [FAN] (on)
[17179630.724000] ibm_acpi: ec object not found
[17179630.760000] pcc_acpi: loading...
[17179630.832000] ACPI: Thermal Zone [THRM] (48 C)
[17179650.316000] ppdev: user-space parallel port driver
[17179653.832000] powernow-k8: Processor cpuid 681 not supported
[17179658.528000] [drm] Initialized drm 1.0.1 20051102
[17179658.808000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level,
low) -> IRQ 20
[17179658.808000] PCI: Via IRQ fixup for 0000:01:00.0, from 11 to 4
[17179658.812000] [drm] Initialized via 2.7.4 20051116 on minor 0
[17179658.824000] agpgart: Found an AGP 3.5 compliant device at
0000:00:00.0.
[17179658.824000] agpgart: Device is in legacy mode, falling back to 2.x
[17179658.824000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x
mode
[17179658.824000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x
mode
================== end dmesg 2.6.15-27=======================
output of "less /proc/bus/usb/devices" working Mepis 2.6.10
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.10 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.10 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.1
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 17/900 us ( 2%), #Int= 1, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.10 uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.0
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=085a ProdID=0008 Rev= 2.08
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 90mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=kaweth
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.10 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:10.3
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
=================end of /proc/bus/usb/devices for Mepis 2.6.10=====
output of "less /proc/bus/usb/devices" NON working Mepis 2.6.15-27
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.15-27-desktop uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.15-27-desktop uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.15-27-desktop uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:10.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.15-27-desktop ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:10.3
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0781 ProdID=5150 Rev= 0.10
S: Manufacturer=SanDisk Corporation
S: Product=Cruzer Mini
S: SerialNumber=SNDK4D166402D5F00505
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=200mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
=====================end of /proc/bus/usb/devices NON working 2.6.15-27
Output of lsusb -v Mepis 2.6.10 working :
Bus 004 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.10 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:10.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x08
PortPwrCtrlMask 0xf8
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Bus 003 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.10 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:10.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x08
PortPwrCtrlMask 0xf8
Hub Port Status:
Port 1: 0000.0300 lowspeed power
Port 2: 0000.0100 power
Bus 002 Device 002: ID 085a:0008 Xircom
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x085a Xircom
idProduct 0x0008
bcdDevice 2.08
iManufacturer 2
iProduct 3
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
MaxPower 90mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 0 (Defined at Interface level)
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 1
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.10 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:10.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x08
PortPwrCtrlMask 0xf8
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0103 power enable connect
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.10 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:10.3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x0008
Ganged power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x08
PortPwrCtrlMask 0xf8
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0001.0000 C_CONNECT
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
============== end of lsusb -v for Mepis 2.6.10 working version====
output of lsusb -v for Mepis 2.6.15-27:
Bus 004 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.15-27-desktop uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:10.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x48
PortPwrCtrlMask 0xc0
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 003 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.15-27-desktop uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:10.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0xc0
Hub Port Status:
Port 1: 0000.0300 lowspeed power
Port 2: 0000.0100 power
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.15-27-desktop uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:10.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x38
PortPwrCtrlMask 0xc1
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0101 power connect
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
Bus 001 Device 004: ID 0781:5150 SanDisk Corp. SDCZ2 Cruzer Mini Flash
Drive (thin)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5150 SDCZ2 Cruzer Mini Flash Drive (thin)
bcdDevice 0.10
iManufacturer 1 SanDisk Corporation
iProduct 2 Cruzer Mini
iSerial 3 SNDK4D166402D5F00505
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.15-27-desktop ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:10.3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x78
PortPwrCtrlMask 0x01
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0000
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0503 highspeed power enable connect
Port 6: 0000.0100 power
Device Status: 0x0001
Self Powered
=======end of lsusb-v for Mepis 2.6.15-27 non working=======
============END OF TEST DATA=====================
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel