[PATCH 25/78] USB: overhaul of mos7840 driver
Greg Kroah-Hartman <[email protected]>
| Newsgroups | gmane.linux.usb.devel |
|---|---|
| Message-ID | <[email protected]> |
From: Oliver Neukum <[email protected]> This fixes: - breaking DMA rules about buffers - usage of _global_ variables to save a single device's attributes - racy access to urb->status - smp monotonity issue with statistics - use of one buffer for many simultaneous URBs - error handling introduced - several instances of following NULL pointers - use after free - unnecessary GFP_ATOMIC - GFP_KERNEL in interrupt - various cleanups - write room granularity issue that bit cdc-acm - race in shutdown Signed-off-by: Oliver Neukum <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> --- drivers/usb/serial/mos7840.c | 233 ++++++++++++++++++++++++++---------------- 1 files changed, 145 insertions(+), 88 deletions(-) diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index c6cca85..2366e7b 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -176,9 +176,12 @@ struct moschip_port { int port_num; /*Actual port number in the device(1,2,etc) */ struct urb *write_urb; /* write URB for this port */ struct urb *read_urb; /* read URB for this port */ + struct urb *int_urb; __u8 shadowLCR; /* last LCR value received */ __u8 shadowMCR; /* last MCR value received */ char open; + char open_ports; + char zombie; wait_queue_head_t wait_chase; /* for handling sleeping while waiting for chase to finish */ wait_queue_head_t delta_msr_wait; /* for handling sleeping while waiting for msr change to happen */ int delta_msr_cond; @@ -191,17 +194,17 @@ struct moschip_port { __u8 DcrRegOffset; //for processing control URBS in interrupt context struct urb *control_urb; + struct usb_ctrlrequest *dr; char *ctrl_buf; int MsrLsr; + spinlock_t pool_lock; struct urb *write_urb_pool[NUM_URBS]; + char busy[NUM_URBS]; }; static int debug; -static int mos7840_num_ports; //this says the number of ports in the device -static int mos7840_num_open_ports; - /* * mos7840_set_reg_sync @@ -254,7 +257,7 @@ static int mos7840_set_uart_reg(struct usb_serial_port *port, __u16 reg, struct usb_device *dev = port->serial->dev; val = val & 0x00ff; // For the UART control registers, the application number need to be Or'ed - if (mos7840_num_ports == 4) { + if (port->serial->num_ports == 4) { val |= (((__u16) port->number - (__u16) (port->serial->minor)) + 1) << 8; @@ -294,7 +297,7 @@ static int mos7840_get_uart_reg(struct usb_serial_port *port, __u16 reg, //dbg("application number is %4x \n",(((__u16)port->number - (__u16)(port->serial->minor))+1)<<8); /*Wval is same as application number */ - if (mos7840_num_ports == 4) { + if (port->serial->num_ports == 4) { Wval = (((__u16) port->number - (__u16) (port->serial->minor)) + 1) << 8; @@ -352,7 +355,7 @@ static inline struct moschip_port *mos7840_get_port_private(struct return (struct moschip_port *)usb_get_serial_port_data(port); } -static int mos7840_handle_new_msr(struct moschip_port *port, __u8 new_msr) +static void mos7840_handle_new_msr(struct moschip_port *port, __u8 new_msr) { struct moschip_port *mos7840_port; struct async_icount *icount; @@ -366,22 +369,24 @@ static int mos7840_handle_new_msr(struct moschip_port *port, __u8 new_msr) /* update input line counters */ if (new_msr & MOS_MSR_DELTA_CTS) { icount->cts++; + smp_wmb(); } if (new_msr & MOS_MSR_DELTA_DSR) { icount->dsr++; + smp_wmb(); } if (new_msr & MOS_MSR_DELTA_CD) { icount->dcd++; + smp_wmb(); } if (new_msr & MOS_MSR_DELTA_RI) { icount->rng++; + smp_wmb(); } } - - return 0; } -static int mos7840_handle_new_lsr(struct moschip_port *port, __u8 new_lsr) +static void mos7840_handle_new_lsr(struct moschip_port *port, __u8 new_lsr) { struct async_icount *icount; @@ -400,18 +405,20 @@ static int mos7840_handle_new_lsr(struct moschip_port *port, __u8 new_lsr) icount = &port->icount; if (new_lsr & SERIAL_LSR_BI) { icount->brk++; + smp_wmb(); } if (new_lsr & SERIAL_LSR_OE) { icount->overrun++; + smp_wmb(); } if (new_lsr & SERIAL_LSR_PE) { icount->parity++; + smp_wmb(); } if (new_lsr & SERIAL_LSR_FE) { icount->frame++; + smp_wmb(); } - - return 0; } /************************************************************************/ @@ -426,12 +433,15 @@ static void mos7840_control_callback(struct urb *urb) unsigned char *data; struct moschip_port *mos7840_port; __u8 regval = 0x0; + int result = 0; if (!urb) { dbg("%s", "Invalid Pointer !!!!:\n"); return; } + mos7840_port = (struct moschip_port *)urb->context; + switch (urb->status) { case 0: /* success */ @@ -449,8 +459,6 @@ static void mos7840_control_callback(struct urb *urb) goto exit; } - mos7840_port = (struct moschip_port *)urb->context; - dbg("%s urb buffer size is %d\n", __FUNCTION__, urb->actual_length); dbg("%s mos7840_port->MsrLsr is %d port %d\n", __FUNCTION__, mos7840_port->MsrLsr, mos7840_port->port_num); @@ -462,21 +470,26 @@ static void mos7840_control_callback(struct urb *urb) else if (mos7840_port->MsrLsr == 1) mos7840_handle_new_lsr(mos7840_port, regval); - exit: - return; +exit: + spin_lock(&mos7840_port->pool_lock); + if (!mos7840_port->zombie) + result = usb_submit_urb(mos7840_port->int_urb, GFP_ATOMIC); + spin_unlock(&mos7840_port->pool_lock); + if (result) { + dev_err(&urb->dev->dev, + "%s - Error %d submitting interrupt urb\n", + __FUNCTION__, result); + } } static int mos7840_get_reg(struct moschip_port *mcs, __u16 Wval, __u16 reg, __u16 * val) { struct usb_device *dev = mcs->port->serial->dev; - struct usb_ctrlrequest *dr = NULL; - unsigned char *buffer = NULL; - int ret = 0; - buffer = (__u8 *) mcs->ctrl_buf; + struct usb_ctrlrequest *dr = mcs->dr; + unsigned char *buffer = mcs->ctrl_buf; + int ret; -// dr=(struct usb_ctrlrequest *)(buffer); - dr = (void *)(buffer + 2); dr->bRequestType = MCS_RD_RTYPE; dr->bRequest = MCS_RDREQ; dr->wValue = cpu_to_le16(Wval); //0; @@ -506,8 +519,8 @@ static void mos7840_interrupt_callback(struct urb *urb) __u16 Data; unsigned char *data; __u8 sp[5], st; - int i; - __u16 wval; + int i, rv = 0; + __u16 wval, wreg = 0; dbg("%s", " : Entering\n"); if (!urb) { @@ -569,31 +582,34 @@ static void mos7840_interrupt_callback(struct urb *urb) dbg("Serial Port %d: Receiver status error or ", i); dbg("address bit detected in 9-bit mode\n"); mos7840_port->MsrLsr = 1; - mos7840_get_reg(mos7840_port, wval, - LINE_STATUS_REGISTER, - &Data); + wreg = LINE_STATUS_REGISTER; break; case SERIAL_IIR_MS: dbg("Serial Port %d: Modem status change\n", i); mos7840_port->MsrLsr = 0; - mos7840_get_reg(mos7840_port, wval, - MODEM_STATUS_REGISTER, - &Data); + wreg = MODEM_STATUS_REGISTER; break; } + spin_lock(&mos7840_port->pool_lock); + if (!mos7840_port->zombie) { + rv = mos7840_get_reg(mos7840_port, wval, wreg, &Data); + } else { + spin_unlock(&mos7840_port->pool_lock); + return; + } + spin_unlock(&mos7840_port->pool_lock); } } } - exit: + if (!(rv < 0)) /* the completion handler for the control urb will resubmit */ + return; +exit: result = usb_submit_urb(urb, GFP_ATOMIC); if (result) { dev_err(&urb->dev->dev, "%s - Error %d submitting interrupt urb\n", __FUNCTION__, result); } - - return; - } static int mos7840_port_paranoia_check(struct usb_serial_port *port, @@ -634,7 +650,8 @@ static struct usb_serial *mos7840_get_usb_serial(struct usb_serial_port *port, if (!port || mos7840_port_paranoia_check(port, function) || mos7840_serial_paranoia_check(port->serial, function)) { - /* then say that we don't have a valid usb_serial thing, which will * end up genrating -ENODEV return values */ + /* then say that we don't have a valid usb_serial thing, which will + * end up genrating -ENODEV return values */ return NULL; } @@ -699,6 +716,7 @@ static void mos7840_bulk_in_callback(struct urb *urb) tty_flip_buffer_push(tty); } mos7840_port->icount.rx += urb->actual_length; + smp_wmb(); dbg("mos7840_port->icount.rx is %d:\n", mos7840_port->icount.rx); } @@ -708,15 +726,14 @@ static void mos7840_bulk_in_callback(struct urb *urb) return; } - if (mos7840_port->read_urb->status != -EINPROGRESS) { - mos7840_port->read_urb->dev = serial->dev; - status = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC); + mos7840_port->read_urb->dev = serial->dev; - if (status) { - dbg(" usb_submit_urb(read bulk) failed, status = %d", - status); - } + status = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC); + + if (status) { + dbg(" usb_submit_urb(read bulk) failed, status = %d", + status); } } @@ -730,17 +747,28 @@ static void mos7840_bulk_out_data_callback(struct urb *urb) { struct moschip_port *mos7840_port; struct tty_struct *tty; + int i; + if (!urb) { dbg("%s", "Invalid Pointer !!!!:\n"); return; } + mos7840_port = (struct moschip_port *)urb->context; + spin_lock(&mos7840_port->pool_lock); + for (i = 0; i < NUM_URBS; i++) { + if (urb == mos7840_port->write_urb_pool[i]) { + mos7840_port->busy[i] = 0; + break; + } + } + spin_unlock(&mos7840_port->pool_lock); + if (urb->status) { dbg("nonzero write bulk status received:%d\n", urb->status); return; } - mos7840_port = (struct moschip_port *)urb->context; if (!mos7840_port) { dbg("%s", "NULL mos7840_port pointer \n"); return; @@ -792,13 +820,13 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) __u16 Data; int status; struct moschip_port *mos7840_port; + struct moschip_port *port0; if (mos7840_port_paranoia_check(port, __FUNCTION__)) { dbg("%s", "Port Paranoia failed \n"); return -ENODEV; } - mos7840_num_open_ports++; serial = port->serial; if (mos7840_serial_paranoia_check(serial, __FUNCTION__)) { @@ -807,16 +835,18 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) } mos7840_port = mos7840_get_port_private(port); + port0 = mos7840_get_port_private(serial->port[0]); - if (mos7840_port == NULL) + if (mos7840_port == NULL || port0 == NULL) return -ENODEV; usb_clear_halt(serial->dev, port->write_urb->pipe); usb_clear_halt(serial->dev, port->read_urb->pipe); + port0->open_ports++; /* Initialising the write urb pool */ for (j = 0; j < NUM_URBS; ++j) { - urb = usb_alloc_urb(0, GFP_ATOMIC); + urb = usb_alloc_urb(0, GFP_KERNEL); mos7840_port->write_urb_pool[j] = urb; if (urb == NULL) { @@ -824,10 +854,10 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) continue; } - urb->transfer_buffer = NULL; - urb->transfer_buffer = - kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); + urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL); if (!urb->transfer_buffer) { + usb_free_urb(urb); + mos7840_port->write_urb_pool[j] = NULL; err("%s-out of memory for urb buffers.", __FUNCTION__); continue; } @@ -879,9 +909,7 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) } Data |= 0x08; //Driver done bit Data |= 0x20; //rx_disable - status = 0; - status = - mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset, Data); + status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset, Data); if (status < 0) { dbg("writing Controlreg failed\n"); return -1; @@ -893,7 +921,6 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) //////////////////////////////////// Data = 0x00; - status = 0; status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); if (status < 0) { dbg("disableing interrupts failed\n"); @@ -901,7 +928,6 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) } // Set FIFO_CONTROL_REGISTER to the default value Data = 0x00; - status = 0; status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); if (status < 0) { dbg("Writing FIFO_CONTROL_REGISTER failed\n"); @@ -909,7 +935,6 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) } Data = 0xcf; - status = 0; status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); if (status < 0) { dbg("Writing FIFO_CONTROL_REGISTER failed\n"); @@ -917,22 +942,18 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) } Data = 0x03; - status = 0; status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data); mos7840_port->shadowLCR = Data; Data = 0x0b; - status = 0; status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); mos7840_port->shadowMCR = Data; Data = 0x00; - status = 0; status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data); mos7840_port->shadowLCR = Data; Data |= SERIAL_LCR_DLAB; //data latch enable in LCR 0x80 - status = 0; status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data); Data = 0x0c; @@ -999,7 +1020,7 @@ static int mos7840_open(struct usb_serial_port *port, struct file *filp) /* Check to see if we've set up our endpoint info yet * * (can't set it up in mos7840_startup as the structures * * were not set up at that time.) */ - if (mos7840_num_open_ports == 1) { + if (port0->open_ports == 1) { if (serial->port[0]->interrupt_in_buffer == NULL) { /* set up interrupt urb */ @@ -1097,6 +1118,7 @@ static int mos7840_chars_in_buffer(struct usb_serial_port *port) { int i; int chars = 0; + unsigned long flags; struct moschip_port *mos7840_port; dbg("%s \n", " mos7840_chars_in_buffer:entering ..........."); @@ -1112,13 +1134,15 @@ static int mos7840_chars_in_buffer(struct usb_serial_port *port) return -1; } + spin_lock_irqsave(&mos7840_port->pool_lock,flags); for (i = 0; i < NUM_URBS; ++i) { - if (mos7840_port->write_urb_pool[i]->status == -EINPROGRESS) { + if (mos7840_port->busy[i]) { chars += URB_TRANSFER_BUFFER_SIZE; } } + spin_unlock_irqrestore(&mos7840_port->pool_lock,flags); dbg("%s - returns %d", __FUNCTION__, chars); - return (chars); + return chars; } @@ -1172,6 +1196,7 @@ static void mos7840_close(struct usb_serial_port *port, struct file *filp) { struct usb_serial *serial; struct moschip_port *mos7840_port; + struct moschip_port *port0; int j; __u16 Data; @@ -1189,10 +1214,10 @@ static void mos7840_close(struct usb_serial_port *port, struct file *filp) } mos7840_port = mos7840_get_port_private(port); + port0 = mos7840_get_port_private(serial->port[0]); - if (mos7840_port == NULL) { + if (mos7840_port == NULL || port0 == NULL) return; - } for (j = 0; j < NUM_URBS; ++j) usb_kill_urb(mos7840_port->write_urb_pool[j]); @@ -1234,12 +1259,13 @@ static void mos7840_close(struct usb_serial_port *port, struct file *filp) } // if(mos7840_port->ctrl_buf != NULL) // kfree(mos7840_port->ctrl_buf); - mos7840_num_open_ports--; + port0->open_ports--; dbg("mos7840_num_open_ports in close%d:in port%d\n", - mos7840_num_open_ports, port->number); - if (mos7840_num_open_ports == 0) { + port0->open_ports, port->number); + if (port0->open_ports == 0) { if (serial->port[0]->interrupt_in_urb) { dbg("%s", "Shutdown interrupt_in_urb\n"); + usb_kill_urb(serial->port[0]->interrupt_in_urb); } } @@ -1368,6 +1394,7 @@ static int mos7840_write_room(struct usb_serial_port *port) { int i; int room = 0; + unsigned long flags; struct moschip_port *mos7840_port; dbg("%s \n", " mos7840_write_room:entering ..........."); @@ -1384,14 +1411,17 @@ static int mos7840_write_room(struct usb_serial_port *port) return -1; } + spin_lock_irqsave(&mos7840_port->pool_lock, flags); for (i = 0; i < NUM_URBS; ++i) { - if (mos7840_port->write_urb_pool[i]->status != -EINPROGRESS) { + if (!mos7840_port->busy[i]) { room += URB_TRANSFER_BUFFER_SIZE; } } + spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); + room = (room == 0) ? 0 : room - URB_TRANSFER_BUFFER_SIZE + 1; dbg("%s - returns %d", __FUNCTION__, room); - return (room); + return room; } @@ -1410,6 +1440,7 @@ static int mos7840_write(struct usb_serial_port *port, int i; int bytes_sent = 0; int transfer_size; + unsigned long flags; struct moschip_port *mos7840_port; struct usb_serial *serial; @@ -1476,13 +1507,16 @@ static int mos7840_write(struct usb_serial_port *port, /* try to find a free urb in the list */ urb = NULL; + spin_lock_irqsave(&mos7840_port->pool_lock, flags); for (i = 0; i < NUM_URBS; ++i) { - if (mos7840_port->write_urb_pool[i]->status != -EINPROGRESS) { + if (!mos7840_port->busy[i]) { + mos7840_port->busy[i] = 1; urb = mos7840_port->write_urb_pool[i]; dbg("\nURB:%d", i); break; } } + spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); if (urb == NULL) { dbg("%s - no more free urbs", __FUNCTION__); @@ -1518,6 +1552,7 @@ static int mos7840_write(struct usb_serial_port *port, status = usb_submit_urb(urb, GFP_ATOMIC); if (status) { + mos7840_port->busy[i] = 0; err("%s - usb_submit_urb(write bulk) failed with status = %d", __FUNCTION__, status); bytes_sent = status; @@ -1525,6 +1560,7 @@ static int mos7840_write(struct usb_serial_port *port, } bytes_sent = transfer_size; mos7840_port->icount.tx += transfer_size; + smp_wmb(); dbg("mos7840_port->icount.tx is %d:\n", mos7840_port->icount.tx); exit: @@ -2490,6 +2526,7 @@ static int mos7840_ioctl(struct usb_serial_port *port, struct file *file, if (signal_pending(current)) return -ERESTARTSYS; cnow = mos7840_port->icount; + smp_rmb(); if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) return -EIO; /* no change => error */ @@ -2506,6 +2543,7 @@ static int mos7840_ioctl(struct usb_serial_port *port, struct file *file, case TIOCGICOUNT: cnow = mos7840_port->icount; + smp_rmb(); icount.cts = cnow.cts; icount.dsr = cnow.dsr; icount.rng = cnow.rng; @@ -2535,19 +2573,18 @@ static int mos7840_ioctl(struct usb_serial_port *port, struct file *file, static int mos7840_calc_num_ports(struct usb_serial *serial) { + int mos7840_num_ports = 0; dbg("numberofendpoints: %d \n", (int)serial->interface->cur_altsetting->desc.bNumEndpoints); dbg("numberofendpoints: %d \n", (int)serial->interface->altsetting->desc.bNumEndpoints); if (serial->interface->cur_altsetting->desc.bNumEndpoints == 5) { - mos7840_num_ports = 2; - serial->type->num_ports = 2; + mos7840_num_ports = serial->num_ports = 2; } else if (serial->interface->cur_altsetting->desc.bNumEndpoints == 9) { - mos7840_num_ports = 4; - serial->type->num_bulk_in = 4; - serial->type->num_bulk_out = 4; - serial->type->num_ports = 4; + serial->num_bulk_in = 4; + serial->num_bulk_out = 4; + mos7840_num_ports = serial->num_ports = 4; } return mos7840_num_ports; @@ -2583,7 +2620,9 @@ static int mos7840_startup(struct usb_serial *serial) mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL); if (mos7840_port == NULL) { err("%s - Out of memory", __FUNCTION__); - return -ENOMEM; + status = -ENOMEM; + i--; /* don't follow NULL pointer cleaning up */ + goto error; } /* Initialize all port interrupt end point to port 0 int endpoint * @@ -2591,6 +2630,7 @@ static int mos7840_startup(struct usb_serial *serial) mos7840_port->port = serial->port[i]; mos7840_set_port_private(serial->port[i], mos7840_port); + spin_lock_init(&mos7840_port->pool_lock); mos7840_port->port_num = ((serial->port[i]->number - (serial->port[i]->serial->minor)) + @@ -2601,22 +2641,22 @@ static int mos7840_startup(struct usb_serial *serial) mos7840_port->ControlRegOffset = 0x1; mos7840_port->DcrRegOffset = 0x4; } else if ((mos7840_port->port_num == 2) - && (mos7840_num_ports == 4)) { + && (serial->num_ports == 4)) { mos7840_port->SpRegOffset = 0x8; mos7840_port->ControlRegOffset = 0x9; mos7840_port->DcrRegOffset = 0x16; } else if ((mos7840_port->port_num == 2) - && (mos7840_num_ports == 2)) { + && (serial->num_ports == 2)) { mos7840_port->SpRegOffset = 0xa; mos7840_port->ControlRegOffset = 0xb; mos7840_port->DcrRegOffset = 0x19; } else if ((mos7840_port->port_num == 3) - && (mos7840_num_ports == 4)) { + && (serial->num_ports == 4)) { mos7840_port->SpRegOffset = 0xa; mos7840_port->ControlRegOffset = 0xb; mos7840_port->DcrRegOffset = 0x19; } else if ((mos7840_port->port_num == 4) - && (mos7840_num_ports == 4)) { + && (serial->num_ports == 4)) { mos7840_port->SpRegOffset = 0xc; mos7840_port->ControlRegOffset = 0xd; mos7840_port->DcrRegOffset = 0x1c; @@ -2701,21 +2741,19 @@ static int mos7840_startup(struct usb_serial *serial) dbg("CLK_START_VALUE_REGISTER Writing success status%d\n", status); Data = 0x20; - status = 0; status = mos7840_set_reg_sync(serial->port[i], CLK_MULTI_REGISTER, Data); if (status < 0) { dbg("Writing CLK_MULTI_REGISTER failed status-0x%x\n", status); - break; + goto error; } else dbg("CLK_MULTI_REGISTER Writing success status%d\n", status); //write value 0x0 to scratchpad register Data = 0x00; - status = 0; status = mos7840_set_uart_reg(serial->port[i], SCRATCH_PAD_REGISTER, Data); @@ -2729,7 +2767,7 @@ static int mos7840_startup(struct usb_serial *serial) //Zero Length flag register if ((mos7840_port->port_num != 1) - && (mos7840_num_ports == 2)) { + && (serial->num_ports == 2)) { Data = 0xff; status = 0; @@ -2770,14 +2808,17 @@ static int mos7840_startup(struct usb_serial *serial) i + 1, status); } - mos7840_port->control_urb = usb_alloc_urb(0, GFP_ATOMIC); + mos7840_port->control_urb = usb_alloc_urb(0, GFP_KERNEL); mos7840_port->ctrl_buf = kmalloc(16, GFP_KERNEL); - + mos7840_port->dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_KERNEL); + if (!mos7840_port->control_urb || !mos7840_port->ctrl_buf || !mos7840_port->dr) { + status = -ENOMEM; + goto error; + } } //Zero Length flag enable Data = 0x0f; - status = 0; status = mos7840_set_reg_sync(serial->port[0], ZLP_REG5, Data); if (status < 0) { dbg("Writing ZLP_REG5 failed status-0x%x\n", status); @@ -2789,6 +2830,17 @@ static int mos7840_startup(struct usb_serial *serial) usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), (__u8) 0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5 * HZ); return 0; +error: + for (/* nothing */; i >= 0; i--) { + mos7840_port = mos7840_get_port_private(serial->port[i]); + + kfree(mos7840_port->dr); + kfree(mos7840_port->ctrl_buf); + usb_free_urb(mos7840_port->control_urb); + kfree(mos7840_port); + serial->port[i] = NULL; + } + return status; } /**************************************************************************** @@ -2799,6 +2851,7 @@ static int mos7840_startup(struct usb_serial *serial) static void mos7840_shutdown(struct usb_serial *serial) { int i; + unsigned long flags; struct moschip_port *mos7840_port; dbg("%s \n", " shutdown :entering.........."); @@ -2814,8 +2867,12 @@ static void mos7840_shutdown(struct usb_serial *serial) for (i = 0; i < serial->num_ports; ++i) { mos7840_port = mos7840_get_port_private(serial->port[i]); - kfree(mos7840_port->ctrl_buf); + spin_lock_irqsave(&mos7840_port->pool_lock, flags); + mos7840_port->zombie = 1; + spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); usb_kill_urb(mos7840_port->control_urb); + kfree(mos7840_port->ctrl_buf); + kfree(mos7840_port->dr); kfree(mos7840_port); mos7840_set_port_private(serial->port[i], NULL); } -- 1.5.1.2 ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ [email protected] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel