[PATCH 037/149] USB: ehci_fsl update for MPC831x support
Greg Kroah-Hartman <[email protected]>
| Newsgroups | gmane.linux.usb.devel |
|---|---|
| Message-ID | <[email protected]> |
From: Li Yang <[email protected]> For MPC831x support, change the ehci-fsl driver to preserve bits set in platform code. Add a common CONFIG_USB_EHCI_FSL to indicate presence of Freescale EHCI SOC. Add FSL_USB2_DR_OTG operating mode support, thus both host and device can work for the mini-ab receptacle. Note: this doesn't enable OTG protocol support. Signed-off-by: Li Yang <[email protected]> Cc: David Brownell <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> --- drivers/usb/host/Kconfig | 7 +++++++ drivers/usb/host/ehci-fsl.c | 10 +++++++--- drivers/usb/host/ehci-hcd.c | 2 +- 3 files changed, 15 insertions(+), 4 deletions(-) diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index a2bcca8..2f52982 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -77,6 +77,13 @@ config USB_EHCI_BIG_ENDIAN_DESC depends on USB_EHCI_HCD && 440EPX default y +config USB_EHCI_FSL + bool + select USB_EHCI_ROOT_HUB_TT + default y if MPC834x || PPC_MPC831x + ---help--- + Variation of ARC USB block used in some Freescale chips. + config USB_ISP116X_HCD tristate "ISP116X HCD support" depends on USB diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c index c7a7c59..b7b7bfb 100644 --- a/drivers/usb/host/ehci-fsl.c +++ b/drivers/usb/host/ehci-fsl.c @@ -67,7 +67,8 @@ int usb_hcd_fsl_probe(const struct hc_driver *driver, * in host mode. */ if (!((pdata->operating_mode == FSL_USB2_DR_HOST) || - (pdata->operating_mode == FSL_USB2_MPH_HOST))) { + (pdata->operating_mode == FSL_USB2_MPH_HOST) || + (pdata->operating_mode == FSL_USB2_DR_OTG))) { dev_err(&pdev->dev, "Non Host Mode configured for %s. Wrong driver linked.\n", pdev->dev.bus_id); @@ -185,12 +186,14 @@ static void mpc83xx_usb_setup(struct usb_hcd *hcd) struct ehci_hcd *ehci = hcd_to_ehci(hcd); struct fsl_usb2_platform_data *pdata; void __iomem *non_ehci = hcd->regs; + u32 temp; pdata = (struct fsl_usb2_platform_data *)hcd->self.controller-> platform_data; /* Enable PHY interface in the control reg. */ - out_be32(non_ehci + FSL_SOC_USB_CTRL, 0x00000004); + temp = in_be32(non_ehci + FSL_SOC_USB_CTRL); + out_be32(non_ehci + FSL_SOC_USB_CTRL, temp | 0x00000004); out_be32(non_ehci + FSL_SOC_USB_SNOOP1, 0x0000001b); #if defined(CONFIG_PPC32) && !defined(CONFIG_NOT_COHERENT_CACHE) @@ -206,7 +209,8 @@ static void mpc83xx_usb_setup(struct usb_hcd *hcd) out_be32(non_ehci + FSL_SOC_USB_SNOOP2, 0x80000000 | SNOOP_SIZE_2GB); #endif - if (pdata->operating_mode == FSL_USB2_DR_HOST) + if ((pdata->operating_mode == FSL_USB2_DR_HOST) || + (pdata->operating_mode == FSL_USB2_DR_OTG)) mpc83xx_setup_phy(ehci, pdata->phy_mode, 0); if (pdata->operating_mode == FSL_USB2_MPH_HOST) { diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index f005438..889c202 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -994,7 +994,7 @@ MODULE_LICENSE ("GPL"); #define PCI_DRIVER ehci_pci_driver #endif -#ifdef CONFIG_MPC834x +#ifdef CONFIG_USB_EHCI_FSL #include "ehci-fsl.c" #define PLATFORM_DRIVER ehci_fsl_driver #endif -- 1.5.2.2 ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ [email protected] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel