[PATCH 2/3] USB: break apart flush_endpoint and disable_endpoint

This patch (as988) breaks usb_hcd_endpoint_disable() apart into two
routines.  The first, usb_hcd_flush_endpoint() does the -ESHUTDOWN
unlinking of all URBs in the endpoint's queue and waits for them to
complete.  The second, usb_hcd_disable_endpoint() -- renamed for
better grammatical style -- merely calls the HCD's endpoint_disable
method.  The changeover is easy because the routine currently has only
one caller.

This separation of function will be exploited in the following patch:
When a device is suspended, the core will be able to cancel all
outstanding URBs for that device while leaving the HCD's
endpoint-related data structures intact for later.

As an added benefit, HCDs no longer need to check for existing URBs in
their endpoint_disable methods.  It is now guaranteed that there will
be none.

Signed-off-by: Alan Stern <[email protected]>

---

Index: usb-2.6/drivers/usb/core/hcd.h
===================================================================
--- usb-2.6.orig/drivers/usb/core/hcd.h
+++ usb-2.6/drivers/usb/core/hcd.h
@@ -219,7 +219,9 @@ extern int usb_hcd_submit_urb (struct ur
 extern int usb_hcd_unlink_urb (struct urb *urb, int status);
 extern void usb_hcd_giveback_urb(struct usb_hcd *hcd, struct urb *urb,
 		int status);
-extern void usb_hcd_endpoint_disable (struct usb_device *udev,
+extern void usb_hcd_flush_endpoint(struct usb_device *udev,
+		struct usb_host_endpoint *ep);
+extern void usb_hcd_disable_endpoint(struct usb_device *udev,
 		struct usb_host_endpoint *ep);
 extern int usb_hcd_get_frame_number (struct usb_device *udev);
 
Index: usb-2.6/drivers/usb/core/message.c
===================================================================
--- usb-2.6.orig/drivers/usb/core/message.c
+++ usb-2.6/drivers/usb/core/message.c
@@ -1017,7 +1017,8 @@ void usb_disable_endpoint(struct usb_dev
 	}
 	if (ep) {
 		ep->enabled = 0;
-		usb_hcd_endpoint_disable(dev, ep);
+		usb_hcd_flush_endpoint(dev, ep);
+		usb_hcd_disable_endpoint(dev, ep);
 	}
 }
 
Index: usb-2.6/drivers/usb/core/hcd.c
===================================================================
--- usb-2.6.orig/drivers/usb/core/hcd.c
+++ usb-2.6/drivers/usb/core/hcd.c
@@ -1289,24 +1289,22 @@ EXPORT_SYMBOL (usb_hcd_giveback_urb);
 
 /*-------------------------------------------------------------------------*/
 
-/* disables the endpoint: cancels any pending urbs, then synchronizes with
- * the hcd to make sure all endpoint state is gone from hardware, and then
- * waits until the endpoint's queue is completely drained. use for
- * set_configuration, set_interface, driver removal, physical disconnect.
- *
- * example:  a qh stored in ep->hcpriv, holding state related to endpoint
- * type, maxpacket size, toggle, halt status, and scheduling.
+/* Cancel all URBs pending on this endpoint and wait for the endpoint's
+ * queue to drain completely.  The caller must first insure that no more
+ * URBs can be submitted for this endpoint.
  */
-void usb_hcd_endpoint_disable (struct usb_device *udev,
+void usb_hcd_flush_endpoint(struct usb_device *udev,
 		struct usb_host_endpoint *ep)
 {
 	struct usb_hcd		*hcd;
 	struct urb		*urb;
 
+	if (!ep)
+		return;
 	might_sleep();
 	hcd = bus_to_hcd(udev->bus);
 
-	/* ep is already gone from udev->ep_{in,out}[]; no more submits */
+	/* No more submits can occur */
 rescan:
 	spin_lock_irq(&hcd_urb_list_lock);
 	list_for_each_entry (urb, &ep->urb_list, urb_list) {
@@ -1345,18 +1343,7 @@ rescan:
 	}
 	spin_unlock_irq(&hcd_urb_list_lock);
 
-	/* synchronize with the hardware, so old configuration state
-	 * clears out immediately (and will be freed).
-	 */
-	if (hcd->driver->endpoint_disable)
-		hcd->driver->endpoint_disable (hcd, ep);
-
-	/* Wait until the endpoint queue is completely empty.  Most HCDs
-	 * will have done this already in their endpoint_disable method,
-	 * but some might not.  And there could be root-hub control URBs
-	 * still pending since they aren't affected by the HCDs'
-	 * endpoint_disable methods.
-	 */
+	/* Wait until the endpoint queue is completely empty */
 	while (!list_empty (&ep->urb_list)) {
 		spin_lock_irq(&hcd_urb_list_lock);
 
@@ -1376,6 +1363,25 @@ rescan:
 	}
 }
 
+/* Disables the endpoint: synchronizes with the hcd to make sure all
+ * endpoint state is gone from hardware.  usb_hcd_flush_endpoint() must
+ * have been called previously.  Use for set_configuration, set_interface,
+ * driver removal, physical disconnect.
+ *
+ * example:  a qh stored in ep->hcpriv, holding state related to endpoint
+ * type, maxpacket size, toggle, halt status, and scheduling.
+ */
+void usb_hcd_disable_endpoint(struct usb_device *udev,
+		struct usb_host_endpoint *ep)
+{
+	struct usb_hcd		*hcd;
+
+	might_sleep();
+	hcd = bus_to_hcd(udev->bus);
+	if (hcd->driver->endpoint_disable)
+		hcd->driver->endpoint_disable(hcd, ep);
+}
+
 /*-------------------------------------------------------------------------*/
 
 /* called in any context */


-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel