Re: [Em28xx] ehci_hcd map_single: unable to map unsafe buffer on a standard NSLU2

Information of mplayer with verbose mode :
> david@quengo:~$ mplayer -v -dumpstream -dumpfile file.mpg -nocache 
> dvb://TF1
> MPlayer 1.0rc1-4.1.2-DFSG-free (C) 2000-2006 MPlayer Team
> CPU: ARM
> get_path('codecs.conf') -> '/home/david/.mplayer/codecs.conf'
> Reading /home/david/.mplayer/codecs.conf: Can't open 
> '/home/david/.mplayer/codecs.conf': No such file or directory
> Reading /etc/mplayer/codecs.conf: Can't open 
> '/etc/mplayer/codecs.conf': No such file or directory
> Using built-in default codecs.conf.
> CommandLine: '-v' '-dumpstream' '-dumpfile' 'file.mpg' '-nocache' 
> 'dvb://TF1'
> init_freetype
> Using Unoptimized OnScreenDisplay
> Using nanosleep() timing
> get_path('input.conf') -> '/home/david/.mplayer/input.conf'
> Can't open input config file /home/david/.mplayer/input.conf: No such 
> file or directory
> Can't open input config file /etc/mplayer/input.conf: No such file or 
> directory
> Falling back on default (hardcoded) input config
> Setting up LIRC support...
> mplayer: could not connect to socket
> mplayer: No such file or directory
> Failed to open LIRC support. You will not be able to use your remote 
> control.
> get_path('TF1.conf') -> '/home/david/.mplayer/TF1.conf'
>
> Playing dvb://TF1.
> get_path('sub/') -> '/home/david/.mplayer/sub/'
> TUNER TYPE SEEMS TO BE DVB-T
> get_path('channels.conf.ter') -> '/home/david/.mplayer/channels.conf.ter'
> get_path('channels.conf') -> '/home/david/.mplayer/channels.conf'
> CONFIG_READ FILE: /home/david/.mplayer/channels.conf, type: 2
> TER, NUM: 0, NUM_FIELDS: 11, NAME: TF1, FREQ: 594000000 PIDS:  120  130  0
> TER, NUM: 1, NUM_FIELDS: 11, NAME: M6, FREQ: 482000000 PIDS:  120  130  0
> TER, NUM: 2, NUM_FIELDS: 11, NAME: W9, FREQ: 482000000 PIDS:  220  230  0
> TER, NUM: 3, NUM_FIELDS: 11, NAME: NT1, FREQ: 482000000 PIDS:  320  330  0
> TER, NUM: 4, NUM_FIELDS: 11, NAME: NRJ12, FREQ: 594000000 PIDS:  220  
> 230  0
> TER, NUM: 5, NUM_FIELDS: 11, NAME: LCI, FREQ: 594000000 PIDS:  0  330  0
> DVB_CONFIG, can't open device /dev/dvb/adapter1/frontend0, skipping
> DVB_CONFIG, can't open device /dev/dvb/adapter2/frontend0, skipping
> DVB_CONFIG, can't open device /dev/dvb/adapter3/frontend0, skipping
> OPEN_DVB: prog=TF1, card=1, type=2, vid=0, aid=0
>
> dvb_streaming_start(PROG: TF1, CARD: 1, VID: 0, AID: 0, TYPE: , FILE: 
> (null))
> PROGRAM NUMBER 0: name=TF1, freq=594000000
> DVB_OPEN_DEVICES(3)
> OPEN(0), file /dev/dvb/adapter0/demux0: FD=4, CNT=0
> OPEN(1), file /dev/dvb/adapter0/demux0: FD=5, CNT=1
> OPEN(2), file /dev/dvb/adapter0/demux0: FD=6, CNT=2
> DVB_SET_CHANNEL: new channel name=TF1, card: 0, channel 0
> DIFFERENT TUNING THAN THE PREVIOUS:   -> 0|594000000|2|0|2|3|1|0
> dvb_tune Freq: 594000000
> TUNE_IT, fd_frontend 3, fd_sec 0
> freq 594000000, srate 1087919136, pol @, tone -1095878700, specInv, 
> diseqc 4, fe_modulation_t modulation,fe_code_rate_t HP_CodeRate, 
> fe_transmit_mode_t TransmissionMode,fe_guard_interval_t guardInterval, 
> fe_bandwidth_t bandwidth
> Using DVB card "Zarlink ZL10353 DVB-T"
> tuning DVB-T to 594000000 Hz, bandwidth: 0
> Getting frontend status
> Bit error rate: 0
> Signal strength: 38500
> SNR: 48573
> UNC: 0
> FE_STATUS: FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
> SET PES FILTER ON PID 120 to fd 4, RESULT: 0, ERRNO: 0
> SET PES FILTER ON PID 130 to fd 5, RESULT: 0, ERRNO: 0
> SET PES FILTER ON PID 0 to fd 6, RESULT: 0, ERRNO: 0
> SUCCESSFUL EXIT from dvb_streaming_start
> STREAM: [dvbin] dvb://TF1
> STREAM: Description: Dvb Input
> STREAM: Author: Nico
> STREAM: Comment: based on the code from ??? (probably Arpi)
> dvb_streaming_read, attempt N. 6 failed with errno 0 when reading 2048 
> bytes
> dvb_streaming_read, attempt N. 5 failed with errno 0 when reading 2048 
> bytes
> dvb_streaming_read, attempt N. 4 failed with errno 0 when reading 2048 
> bytes
> dvb_streaming_read, attempt N. 3 failed with errno 0 when reading 2048 
> bytes
> dvb_streaming_read, attempt N. 2 failed with errno 0 when reading 2048 
> bytes
> dvb_streaming_read, attempt N. 1 failed with errno 0 when reading 2048 
> bytes
> dvb_streaming_read, return 0 bytes
> Core dumped ;)
> DVBIN_CLOSE, close(2), fd=6, COUNT=2
> DVBIN_CLOSE, close(1), fd=5, COUNT=1
> DVBIN_CLOSE, close(0), fd=4, COUNT=0
> vo: x11 uninit called but X11 not inited..
>
> Exiting... (End of file)
>
>
> Bye
> David
>


-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel