Re: Device detected... But not able to mount device.

Hi,

> Did you enable the partition type you are using on the device?
> Please post the full dmesg.

  By "partition type" you mean the file system? I have the FAT file
system enabled. The full dmesg is as below:

<4>Full speed Hub
<6>usb 1-2: new full speed USB device using imx21-hc and address 2
<4>Full speed Hub
<6>usb 1-2: configuration #1 chosen from 1 choice
<7>usb-storage: USB Mass Storage device detected
<7>usb-storage: -- associate_dev
<7>usb-storage: Vendor: 0x19b6, Product: 0x2048, Revision: 0x0100
<7>usb-storage: Interface Subclass: 0x06, Protocol: 0x50
<7>usb-storage: Transport: Bulk
<7>usb-storage: Protocol: Transparent SCSI
<6>scsi0 : SCSI emulation for USB Mass Storage devices
<7>usb-storage: *** thread sleeping.
<7>usb-storage: device found at 2
<7>usb-storage: waiting for device to settle before scanning
<7>usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
<7>usb-storage: GetMaxLUN command result is 1, data is 1
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command INQUIRY (6 bytes)
<7>usb-storage:  12 00 00 00 24 00
<7>usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
<7>usb-storage: Status code 0; transferred 36/36
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk data transfer result 0x0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<5>scsi 0:0:0:0: Direct-Access     Moser    Baer AZ-601      0.00 PQ: 0 ANSI: 2
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command TEST_UNIT_READY (6 bytes)
<7>usb-storage:  00 00 00 00 00 00
<7>usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command READ_CAPACITY (10 bytes)
<7>usb-storage:  25 00 00 00 00 00 00 00 00 00
<7>usb-storage: Bulk Command S 0x43425355 T 0x3 L 8 F 128 Trg 0 LUN 0 CL 10
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
<7>usb-storage: Status code 0; transferred 8/8
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk data transfer result 0x0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<5>sd 0:0:0:0: [sda] 4020223 512-byte hardware sectors (2058 MB)
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command MODE_SENSE (6 bytes)
<7>usb-storage:  1a 00 3f 00 c0 00
<7>usb-storage: Bulk Command S 0x43425355 T 0x4 L 192 F 128 Trg 0 LUN 0 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
<7>usb-storage: Status code 0; transferred 8/192
<7>usb-storage: -- short transfer
<7>usb-storage: Bulk data transfer result 0x1
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
<3>sd 0:0:0:0: [sda] Assuming drive cache: write through
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command TEST_UNIT_READY (6 bytes)
<7>usb-storage:  00 00 00 00 00 00
<7>usb-storage: Bulk Command S 0x43425355 T 0x5 L 0 F 0 Trg 0 LUN 0 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
<7>usb-storage:  1e 00 00 00 01 00
<7>usb-storage: Bulk Command S 0x43425355 T 0x6 L 0 F 0 Trg 0 LUN 0 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x1
<7>usb-storage: -- transport indicates command failure
<7>usb-storage: Issuing auto-REQUEST_SENSE
<7>usb-storage: Bulk Command S 0x43425355 T 0x7 L 18 F 128 Trg 0 LUN 0 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 18 bytes
<7>usb-storage: Status code 0; transferred 18/18
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk data transfer result 0x0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x0
<7>usb-storage: -- Result from auto-sense is 0
<7>usb-storage: -- code: 0x70, key: 0x5, ASC: 0x24, ASCQ: 0x0
<7>usb-storage: Illegal Request: Invalid field in cdb
<7>usb-storage: scsi cmd done, result=0x2
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command TEST_UNIT_READY (6 bytes)
<7>usb-storage:  00 00 00 00 00 00
<7>usb-storage: Bulk Command S 0x43425355 T 0x8 L 0 F 0 Trg 0 LUN 0 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command READ_CAPACITY (10 bytes)
<7>usb-storage:  25 00 00 00 00 00 00 00 00 00
<7>usb-storage: Bulk Command S 0x43425355 T 0x9 L 8 F 128 Trg 0 LUN 0 CL 10
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
<7>usb-storage: Status code 0; transferred 8/8
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk data transfer result 0x0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0x9 R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<5>sd 0:0:0:0: [sda] 4020223 512-byte hardware sectors (2058 MB)
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command MODE_SENSE (6 bytes)
<7>usb-storage:  1a 00 3f 00 c0 00
<7>usb-storage: Bulk Command S 0x43425355 T 0xa L 192 F 128 Trg 0 LUN 0 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
<7>usb-storage: Status code 0; transferred 8/192
<7>usb-storage: -- short transfer
<7>usb-storage: Bulk data transfer result 0x1
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
<3>sd 0:0:0:0: [sda] Assuming drive cache: write through
<6> sda:<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command READ_10 (10 bytes)
<7>usb-storage:  28 00 00 00 00 00 00 00 08 00
<7>usb-storage: Bulk Command S 0x43425355 T 0xb L 4096 F 128 Trg 0 LUN 0 CL 10
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
<7>usb-storage: Status code 0; transferred 4096/4096
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk data transfer result 0x0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<4> sda1
<5>sd 0:0:0:0: [sda] Attached SCSI removable disk
<5>sd 0:0:0:0: Attached scsi generic sg0 type 0
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Command INQUIRY (6 bytes)
<7>usb-storage:  12 20 00 00 24 00
<7>usb-storage: Bulk Command S 0x43425355 T 0xc L 36 F 128 Trg 0 LUN 1 CL 6
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
<7>usb-storage: Status code 0; transferred 31/31
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk command transfer result=0
<7>usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
<7>usb-storage: Status code 0; transferred 36/36
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk data transfer result 0x0
<7>usb-storage: Attempting to get CSW...
<7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
<7>usb-storage: Status code 0; transferred 13/13
<7>usb-storage: -- transfer complete
<7>usb-storage: Bulk status result = 0
<7>usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0
<7>usb-storage: scsi cmd done, result=0x0
<7>usb-storage: *** thread sleeping.
<5>scsi 0:0:0:1: CD-ROM            Moser    Baer AZ-601      0.00 PQ:
0 ANSI: 0 CCS
<5>scsi 0:0:0:1: Attached scsi generic sg1 type 5
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Bad LUN (0:2)
<7>usb-storage: scsi cmd done, result=0x40000
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Bad target number (1:0)
<7>usb-storage: scsi cmd done, result=0x40000
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Bad target number (2:0)
<7>usb-storage: scsi cmd done, result=0x40000
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Bad target number (3:0)
<7>usb-storage: scsi cmd done, result=0x40000
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Bad target number (4:0)
<7>usb-storage: scsi cmd done, result=0x40000
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Bad target number (5:0)
<7>usb-storage: scsi cmd done, result=0x40000
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Bad target number (6:0)
<7>usb-storage: scsi cmd done, result=0x40000
<7>usb-storage: *** thread sleeping.
<7>usb-storage: queuecommand called
<7>usb-storage: *** thread awakened.
<7>usb-storage: Bad target number (7:0)
<7>usb-storage: scsi cmd done, result=0x40000
<7>usb-storage: *** thread sleeping.
<7>usb-storage: device scan complete


Midhun.

-------------------------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc.
Still grepping through log files to find problems?  Stop.
Now Search log events and configuration files using AJAX and a browser.
Download your FREE copy of Splunk now >> http://get.splunk.com/
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel