[PATCH 115/142] USB: Driver for CH341 USB-serial adaptor

From: Frank A Kingswood <[email protected]>

This patch implements a USB serial port driver for the Winchiphead
CH341 USB-RS232 Converter. This chip also implements an IEEE 1284
parallel port, I2C and SPI, but that is not supported by the driver.

Signed-off-by: Frank A Kingswood <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
 Documentation/usb/usb-serial.txt |   11 ++
 drivers/usb/serial/Kconfig       |   10 +
 drivers/usb/serial/Makefile      |    1 +
 drivers/usb/serial/ch341.c       |  352 ++++++++++++++++++++++++++++++++++++++
 4 files changed, 374 insertions(+), 0 deletions(-)
 create mode 100644 drivers/usb/serial/ch341.c

diff --git a/Documentation/usb/usb-serial.txt b/Documentation/usb/usb-serial.txt
index 5b635ae..4e0b62b 100644
--- a/Documentation/usb/usb-serial.txt
+++ b/Documentation/usb/usb-serial.txt
@@ -428,6 +428,17 @@ Options supported:
   See http://www.uuhaus.de/linux/palmconnect.html for up-to-date
   information on this driver.
 
+Winchiphead CH341 Driver
+
+  This driver is for the Winchiphead CH341 USB-RS232 Converter. This chip
+  also implements an IEEE 1284 parallel port, I2C and SPI, but that is not
+  supported by the driver. The protocol was analyzed from the behaviour
+  of the Windows driver, no datasheet is available at present.
+  The manufacturer's website: http://www.winchiphead.com/.
+  For any questions or problems with this driver, please contact
+  [email protected].
+
+
 Generic Serial driver
 
   If your device is not one of the above listed devices, compatible with
diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 43d6db6..99fefed 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -92,6 +92,16 @@ config USB_SERIAL_BELKIN
 	  To compile this driver as a module, choose M here: the
 	  module will be called belkin_sa.
 
+config USB_SERIAL_CH341
+	tristate "USB Winchiphead CH341 Single Port Serial Driver"
+	depends on USB_SERIAL
+	help
+	  Say Y here if you want to use a Winchiphead CH341 single port
+	  USB to serial adapter.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ch341.
+
 config USB_SERIAL_WHITEHEAT
 	tristate "USB ConnectTech WhiteHEAT Serial Driver"
 	depends on USB_SERIAL
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index 07a976e..d6fb384 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_USB_SERIAL_AIRCABLE)		+= aircable.o
 obj-$(CONFIG_USB_SERIAL_AIRPRIME)		+= airprime.o
 obj-$(CONFIG_USB_SERIAL_ARK3116)		+= ark3116.o
 obj-$(CONFIG_USB_SERIAL_BELKIN)			+= belkin_sa.o
+obj-$(CONFIG_USB_SERIAL_CH341)			+= ch341.o
 obj-$(CONFIG_USB_SERIAL_CP2101)			+= cp2101.o
 obj-$(CONFIG_USB_SERIAL_CYBERJACK)		+= cyberjack.o
 obj-$(CONFIG_USB_SERIAL_CYPRESS_M8)		+= cypress_m8.o
diff --git a/drivers/usb/serial/ch341.c b/drivers/usb/serial/ch341.c
new file mode 100644
index 0000000..eb68106
--- /dev/null
+++ b/drivers/usb/serial/ch341.c
@@ -0,0 +1,352 @@
+/*
+ * Copyright 2007, Frank A Kingswood <[email protected]>
+ *
+ * ch341.c implements a serial port driver for the Winchiphead CH341.
+ *
+ * The CH341 device can be used to implement an RS232 asynchronous
+ * serial port, an IEEE-1284 parallel printer port or a memory-like
+ * interface. In all cases the CH341 supports an I2C interface as well.
+ * This driver only supports the asynchronous serial interface.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version
+ * 2 as published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include <linux/usb/serial.h>
+#include <linux/serial.h>
+
+#define DEFAULT_BAUD_RATE 2400
+#define DEFAULT_TIMEOUT   1000
+
+static int debug;
+
+static struct usb_device_id id_table [] = {
+	{ USB_DEVICE(0x4348, 0x5523) },
+	{ },
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+struct ch341_private {
+	unsigned baud_rate;
+	u8 dtr;
+	u8 rts;
+};
+
+static int ch341_control_out(struct usb_device *dev, u8 request,
+			     u16 value, u16 index)
+{
+	int r;
+	dbg("ch341_control_out(%02x,%02x,%04x,%04x)", USB_DIR_OUT|0x40,
+		(int)request, (int)value, (int)index);
+
+	r = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request,
+			    USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
+			    value, index, NULL, 0, DEFAULT_TIMEOUT);
+
+	return r;
+}
+
+static int ch341_control_in(struct usb_device *dev,
+			    u8 request, u16 value, u16 index,
+			    char *buf, unsigned bufsize)
+{
+	int r;
+	dbg("ch341_control_in(%02x,%02x,%04x,%04x,%p,%u)", USB_DIR_IN|0x40,
+		(int)request, (int)value, (int)index, buf, (int)bufsize);
+
+	r = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), request,
+			    USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
+			    value, index, buf, bufsize, DEFAULT_TIMEOUT);
+	return r;
+}
+
+int ch341_set_baudrate(struct usb_device *dev, struct ch341_private *priv)
+{
+	short a, b;
+	int r;
+
+	dbg("ch341_set_baudrate(%d)", priv->baud_rate);
+	switch (priv->baud_rate) {
+	case 2400:
+		a = 0xd901;
+		b = 0x0038;
+		break;
+	case 4800:
+		a = 0x6402;
+		b = 0x001f;
+		break;
+	case 9600:
+		a = 0xb202;
+		b = 0x0013;
+		break;
+	case 19200:
+		a = 0xd902;
+		b = 0x000d;
+		break;
+	case 38400:
+		a = 0x6403;
+		b = 0x000a;
+		break;
+	case 115200:
+		a = 0xcc03;
+		b = 0x0008;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	r = ch341_control_out(dev, 0x9a, 0x1312, a);
+	if (!r)
+		r = ch341_control_out(dev, 0x9a, 0x0f2c, b);
+
+	return r;
+}
+
+int ch341_set_handshake(struct usb_device *dev, struct ch341_private *priv)
+{
+	dbg("ch341_set_handshake(%d,%d)", priv->dtr, priv->rts);
+	return ch341_control_out(dev, 0xa4,
+		~((priv->dtr?1<<5:0)|(priv->rts?1<<6:0)), 0);
+}
+
+int ch341_get_status(struct usb_device *dev)
+{
+	char *buffer;
+	int r;
+	const unsigned size = 8;
+
+	dbg("ch341_get_status()");
+
+	buffer = kmalloc(size, GFP_KERNEL);
+	if (!buffer)
+		return -ENOMEM;
+
+	r = ch341_control_in(dev, 0x95, 0x0706, 0, buffer, size);
+	if ( r < 0)
+		goto out;
+
+	/* Not having the datasheet for the CH341, we ignore the bytes returned
+	 * from the device. Return error if the device did not respond in time.
+	 */
+	r = 0;
+
+out:	kfree(buffer);
+	return r;
+}
+
+/* -------------------------------------------------------------------------- */
+
+int ch341_configure(struct usb_device *dev, struct ch341_private *priv)
+{
+	char *buffer;
+	int r;
+	const unsigned size = 8;
+
+	dbg("ch341_configure()");
+
+	buffer = kmalloc(size, GFP_KERNEL);
+	if (!buffer)
+		return -ENOMEM;
+
+	/* expect two bytes 0x27 0x00 */
+	r = ch341_control_in(dev, 0x5f, 0, 0, buffer, size);
+	if (r < 0)
+		goto out;
+
+	r = ch341_control_out(dev, 0xa1, 0, 0);
+	if (r < 0)
+		goto out;
+
+	r = ch341_set_baudrate(dev, priv);
+	if (r < 0)
+		goto out;
+
+	/* expect two bytes 0x56 0x00 */
+	r = ch341_control_in(dev, 0x95, 0x2518, 0, buffer, size);
+	if (r < 0)
+		goto out;
+
+	r = ch341_control_out(dev, 0x9a, 0x2518, 0x0050);
+	if (r < 0)
+		goto out;
+
+	/* expect 0xff 0xee */
+	r = ch341_get_status(dev);
+	if (r < 0)
+		goto out;
+
+	r = ch341_control_out(dev, 0xa1, 0x501f, 0xd90a);
+	if (r < 0)
+		goto out;
+
+	r = ch341_set_baudrate(dev, priv);
+	if (r < 0)
+		goto out;
+
+	r = ch341_set_handshake(dev, priv);
+	if (r < 0)
+		goto out;
+
+	/* expect 0x9f 0xee */
+	r = ch341_get_status(dev);
+
+out:	kfree(buffer);
+	return r;
+}
+
+/* allocate private data */
+static int ch341_attach(struct usb_serial *serial)
+{
+	struct ch341_private *priv;
+	int r;
+
+	dbg("ch341_attach()");
+
+	/* private data */
+	priv = kzalloc(sizeof(struct ch341_private), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->baud_rate = DEFAULT_BAUD_RATE;
+	priv->dtr = 1;
+	priv->rts = 1;
+
+	r = ch341_configure(serial->dev, priv);
+	if (r < 0)
+		goto error;
+
+	usb_set_serial_port_data(serial->port[0], priv);
+	return 0;
+
+error:	kfree(priv);
+	return r;
+}
+
+/* open this device, set default parameters */
+static int ch341_open(struct usb_serial_port *port, struct file *filp)
+{
+	struct usb_serial *serial = port->serial;
+	struct ch341_private *priv = usb_get_serial_port_data(serial->port[0]);
+	int r;
+
+	dbg("ch341_open()");
+
+	priv->baud_rate = DEFAULT_BAUD_RATE;
+	priv->dtr = 1;
+	priv->rts = 1;
+
+	r = ch341_configure(serial->dev, priv);
+	if (r)
+		goto out;
+
+	r = ch341_set_handshake(serial->dev, priv);
+	if (r)
+		goto out;
+
+	r = ch341_set_baudrate(serial->dev, priv);
+	if (r)
+		goto out;
+
+	r = usb_serial_generic_open(port, filp);
+
+out:	return r;
+}
+
+/* Old_termios contains the original termios settings and
+ * tty->termios contains the new setting to be used.
+ */
+static void ch341_set_termios(struct usb_serial_port *port,
+			      struct ktermios *old_termios)
+{
+	struct ch341_private *priv = usb_get_serial_port_data(port);
+	struct tty_struct *tty = port->tty;
+	unsigned baud_rate;
+
+	dbg("ch341_set_termios()");
+
+	if (!tty || !tty->termios)
+		return;
+
+	baud_rate = tty_get_baud_rate(tty);
+
+	switch (baud_rate) {
+	case 2400:
+	case 4800:
+	case 9600:
+	case 19200:
+	case 38400:
+	case 115200:
+		priv->baud_rate = baud_rate;
+		break;
+	default:
+		dbg("Rate %d not supported, using %d",
+			baud_rate, DEFAULT_BAUD_RATE);
+		priv->baud_rate = DEFAULT_BAUD_RATE;
+	}
+
+	ch341_set_baudrate(port->serial->dev, priv);
+
+	/* Unimplemented:
+	 * (cflag & CSIZE) : data bits [5, 8]
+	 * (cflag & PARENB) : parity {NONE, EVEN, ODD}
+	 * (cflag & CSTOPB) : stop bits [1, 2]
+	 */
+}
+
+static struct usb_driver ch341_driver = {
+	.name		= "ch341",
+	.probe		= usb_serial_probe,
+	.disconnect	= usb_serial_disconnect,
+	.id_table	= id_table,
+	.no_dynamic_id	= 1,
+};
+
+static struct usb_serial_driver ch341_device = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= "ch341-uart",
+	},
+	.id_table         = id_table,
+	.usb_driver       = &ch341_driver,
+	.num_interrupt_in = NUM_DONT_CARE,
+	.num_bulk_in      = 1,
+	.num_bulk_out     = 1,
+	.num_ports        = 1,
+	.open             = ch341_open,
+	.set_termios      = ch341_set_termios,
+	.attach           = ch341_attach,
+};
+
+static int __init ch341_init(void)
+{
+	int retval;
+
+	retval = usb_serial_register(&ch341_device);
+	if (retval)
+		return retval;
+	retval = usb_register(&ch341_driver);
+	if (retval)
+		usb_serial_deregister(&ch341_device);
+	return retval;
+}
+
+static void __exit ch341_exit(void)
+{
+	usb_deregister(&ch341_driver);
+	usb_serial_deregister(&ch341_device);
+}
+
+module_init(ch341_init);
+module_exit(ch341_exit);
+MODULE_LICENSE("GPL");
+
+module_param(debug, bool, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(debug, "Debug enabled or not");
+
+/* EOF ch341.c */
-- 
1.5.3.4


-------------------------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc.
Still grepping through log files to find problems?  Stop.
Now Search log events and configuration files using AJAX and a browser.
Download your FREE copy of Splunk now >> http://get.splunk.com/
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel