[PATCH 114/142] USB: cxacru: Use appropriate logging for errors

From: Simon Arlott <[email protected]>

When an error occurs, existing logging uses dbg() so the cause of a
problem is hard to determine. Error conditions shouldn't only be
properly reported with debugging enabled.

A side effect of this change is that when an uninitialised device is
started, a log message similar to the following is sent:
	cxacru 5-2:1.0: receive of cm 0x90 failed (-104)
This is normal - the device did not respond so firmware will be loaded.

Signed-off-by: Simon Arlott <[email protected]>
Acked-by: Duncan Sands <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
---
 drivers/usb/atm/cxacru.c |   43 ++++++++++++++++++++++++++++---------------
 1 files changed, 28 insertions(+), 15 deletions(-)

diff --git a/drivers/usb/atm/cxacru.c b/drivers/usb/atm/cxacru.c
index a73e714..a51eeed 100644
--- a/drivers/usb/atm/cxacru.c
+++ b/drivers/usb/atm/cxacru.c
@@ -482,7 +482,9 @@ static int cxacru_cm(struct cxacru_data *instance, enum cxacru_cm_request cm,
 	int rbuflen = ((rsize - 1) / stride + 1) * CMD_PACKET_SIZE;
 
 	if (wbuflen > PAGE_SIZE || rbuflen > PAGE_SIZE) {
-		dbg("too big transfer requested");
+		if (printk_ratelimit())
+			usb_err(instance->usbatm, "requested transfer size too large (%d, %d)\n",
+				wbuflen, rbuflen);
 		ret = -ENOMEM;
 		goto fail;
 	}
@@ -493,8 +495,9 @@ static int cxacru_cm(struct cxacru_data *instance, enum cxacru_cm_request cm,
 	init_completion(&instance->rcv_done);
 	ret = usb_submit_urb(instance->rcv_urb, GFP_KERNEL);
 	if (ret < 0) {
-		dbg("submitting read urb for cm %#x failed", cm);
-		ret = ret;
+		if (printk_ratelimit())
+			usb_err(instance->usbatm, "submit of read urb for cm %#x failed (%d)\n",
+				cm, ret);
 		goto fail;
 	}
 
@@ -510,27 +513,29 @@ static int cxacru_cm(struct cxacru_data *instance, enum cxacru_cm_request cm,
 	init_completion(&instance->snd_done);
 	ret = usb_submit_urb(instance->snd_urb, GFP_KERNEL);
 	if (ret < 0) {
-		dbg("submitting write urb for cm %#x failed", cm);
-		ret = ret;
+		if (printk_ratelimit())
+			usb_err(instance->usbatm, "submit of write urb for cm %#x failed (%d)\n",
+				cm, ret);
 		goto fail;
 	}
 
 	ret = cxacru_start_wait_urb(instance->snd_urb, &instance->snd_done, NULL);
 	if (ret < 0) {
-		dbg("sending cm %#x failed", cm);
-		ret = ret;
+		if (printk_ratelimit())
+			usb_err(instance->usbatm, "send of cm %#x failed (%d)\n", cm, ret);
 		goto fail;
 	}
 
 	ret = cxacru_start_wait_urb(instance->rcv_urb, &instance->rcv_done, &actlen);
 	if (ret < 0) {
-		dbg("receiving cm %#x failed", cm);
-		ret = ret;
+		if (printk_ratelimit())
+			usb_err(instance->usbatm, "receive of cm %#x failed (%d)\n", cm, ret);
 		goto fail;
 	}
 	if (actlen % CMD_PACKET_SIZE || !actlen) {
-		dbg("response is not a positive multiple of %d: %#x",
-				CMD_PACKET_SIZE, actlen);
+		if (printk_ratelimit())
+			usb_err(instance->usbatm, "invalid response length to cm %#x: %d\n",
+				cm, actlen);
 		ret = -EIO;
 		goto fail;
 	}
@@ -538,12 +543,16 @@ static int cxacru_cm(struct cxacru_data *instance, enum cxacru_cm_request cm,
 	/* check the return status and copy the data to the output buffer, if needed */
 	for (offb = offd = 0; offd < rsize && offb < actlen; offb += CMD_PACKET_SIZE) {
 		if (rbuf[offb] != cm) {
-			dbg("wrong cm %#x in response", rbuf[offb]);
+			if (printk_ratelimit())
+				usb_err(instance->usbatm, "wrong cm %#x in response to cm %#x\n",
+					rbuf[offb], cm);
 			ret = -EIO;
 			goto fail;
 		}
 		if (rbuf[offb + 1] != CM_STATUS_SUCCESS) {
-			dbg("response failed: %#x", rbuf[offb + 1]);
+			if (printk_ratelimit())
+				usb_err(instance->usbatm, "response to cm %#x failed: %#x\n",
+					cm, rbuf[offb + 1]);
 			ret = -EIO;
 			goto fail;
 		}
@@ -582,14 +591,18 @@ static int cxacru_cm_get_array(struct cxacru_data *instance, enum cxacru_cm_requ
 	for (offb = 0; offb < len; ) {
 		int l = le32_to_cpu(buf[offb++]);
 		if (l > stride || l > (len - offb) / 2) {
-			dbg("wrong data length %#x in response", l);
+			if (printk_ratelimit())
+				usb_err(instance->usbatm, "invalid data length from cm %#x: %d\n",
+					cm, l);
 			ret = -EIO;
 			goto cleanup;
 		}
 		while (l--) {
 			offd = le32_to_cpu(buf[offb++]);
 			if (offd >= size) {
-				dbg("wrong index %#x in response", offd);
+				if (printk_ratelimit())
+					usb_err(instance->usbatm, "wrong index #%x in response to cm #%x\n",
+						offd, cm);
 				ret = -EIO;
 				goto cleanup;
 			}
-- 
1.5.3.4


-------------------------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc.
Still grepping through log files to find problems?  Stop.
Now Search log events and configuration files using AJAX and a browser.
Download your FREE copy of Splunk now >> http://get.splunk.com/
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel