backporting of driver mcs7830

/*
 * USB Host-to-Host Links
 * Copyright (C) 2000-2002 by David Brownell <[email protected]>
 * Copyright (C) 2002 Pavel Machek <[email protected]>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */

/*
 * This is used for "USB networking", connecting USB hosts as peers.
 *
 * It can be used with USB "network cables", for IP-over-USB communications;
 * Ethernet speeds without the Ethernet.  USB devices (including some PDAs)
 * can support such links directly, replacing device-specific protocols
 * with Internet standard ones.
 *
 * The links can be bridged using the Ethernet bridging (net/bridge)
 * support as appropriate.  Devices currently supported include:
 *
 *	- AnchorChip 2720
 *	- Belkin, eTEK (interops with Win32 drivers)
 *	- EPSON USB clients
 *	- GeneSys GL620USB-A
 *	- NetChip 1080 (interoperates with NetChip Win32 drivers)
 *	- Prolific PL-2301/2302 (replaces "plusb" driver)
 *	- PXA-250 or SA-1100 Linux PDAs like iPAQ, Yopy, and Zaurus
 *
 * USB devices can implement their side of this protocol at the cost
 * of two bulk endpoints; it's not restricted to "cable" applications.
 * See the SA1110, Zaurus, or EPSON device/client support in this driver;
 * slave/target drivers such as "usb-eth" (on most SA-1100 PDAs) are
 * used inside USB slave/target devices.
 *
 * 
 * Status:
 *
 * - AN2720 ... not widely available, but reportedly works well
 *
 * - Belkin/eTEK ... no known issues
 *
 * - Both GeneSys and PL-230x use interrupt transfers for driver-to-driver
 *   handshaking; it'd be worth implementing those as "carrier detect".
 *   Prefer generic hooks, not minidriver-specific hacks.
 *
 * - For Netchip, should use keventd to poll via control requests to detect
 *   hardware level "carrier detect". 
 *
 * - PL-230x ... the initialization protocol doesn't seem to match chip data
 *   sheets, sometimes it's not needed and sometimes it hangs.  Prolific has
 *   not responded to repeated support/information requests.
 *
 * - SA-1100 PDAs ... the standard ARM Linux SA-1100 support works nicely,
 *   as found in www.handhelds.org and other kernels.  The Sharp/Lineo
 *   kernels use different drivers, which also talk to this code.
 *
 * Interop with more Win32 drivers may be a good thing.
 *
 * Seems like reporting "peer connected" (carrier present) events may end
 * up going through the netlink event system, not hotplug ... so new links
 * would likely be handled with a link monitoring thread in some daemon.
 *
 * There are reports that bridging gives lower-than-usual throughput.
 *
 * Need smarter hotplug policy scripts ... ones that know how to arrange
 * bridging with "brctl", and can handle static and dynamic ("pump") setups.
 * Use those eventual "peer connected" events, and zeroconf.
 *
 *
 * CHANGELOG:
 *
 * 13-sep-2000	experimental, new
 * 10-oct-2000	usb_device_id table created. 
 * 28-oct-2000	misc fixes; mostly, discard more TTL-mangled rx packets.
 * 01-nov-2000	usb_device_id table and probing api update by
 *		Adam J. Richter <[email protected]>.
 * 18-dec-2000	(db) tx watchdog, "net1080" renaming to "usbnet", device_info
 *		and prolific support, isolate net1080-specific bits, cleanup.
 *		fix unlink_urbs oops in D3 PM resume code path.
 *
 * 02-feb-2001	(db) fix tx skb sharing, packet length, match_flags, ...
 * 08-feb-2001	stubbed in "linuxdev", maybe the SA-1100 folk can use it;
 *		AnchorChips 2720 support (from spec) for testing;
 *		fix bit-ordering problem with ethernet multicast addr
 * 19-feb-2001  Support for clearing halt conditions. SA1100 UDC support
 *		updates. Oleg Drokin ([email protected])
 * 25-mar-2001	More SA-1100 updates, including workaround for ip problem
 *		expecting cleared skb->cb and framing change to match latest
 *		handhelds.org version (Oleg).  Enable device IDs from the
 *		Win32 Belkin driver; other cleanups (db).
 * 16-jul-2001	Bugfixes for uhci oops-on-unplug, Belkin support, various
 *		cleanups for problems not yet seen in the field. (db)
 * 17-oct-2001	Handle "Advance USBNET" product, like Belkin/eTEK devices,
 *		from Ioannis Mavroukakis <[email protected]>;
 *		rx unlinks somehow weren't async; minor cleanup.
 * 03-nov-2001	Merged GeneSys driver; original code from Jiun-Jie Huang
 *		<[email protected]>, updated by Stanislav Brabec
 *		<[email protected]>.  Made framing options (NetChip/GeneSys)
 *		tie mostly to (sub)driver info.  Workaround some PL-2302
 *		chips that seem to reject SET_INTERFACE requests.
 *
 * 06-apr-2002	Added ethtool support, based on a patch from Brad Hards.
 *		Level of diagnostics is more configurable; they use device
 *		location (usb_device->devpath) instead of address (2.5).
 *		For tx_fixup, memflags can't be NOIO.
 * 07-may-2002	Generalize/cleanup keventd support, handling rx stalls (mostly
 *		for USB 2.0 TTs) and memory shortages (potential) too. (db)
 *		Use "locally assigned" IEEE802 address space. (Brad Hards)
 * 18-oct-2002	Support for Zaurus (Pavel Machek), related cleanup (db).
 * 15-dec-2002	Partial sync with 2.5 code: cleanups and stubbed PXA-250
 * 		support (db), fix for framing issues on Z, net1080, and
 * 		gl620a (Toby Milne)
 *
 *-------------------------------------------------------------------------*/

#include <linux/config.h>
#include <linux/module.h>
#include <linux/kmod.h>
#include <linux/sched.h>
#include <linux/init.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/random.h>
#include <linux/ethtool.h>
#include <linux/mii.h>
#include <linux/tqueue.h>
#include <asm/uaccess.h>
#include <asm/unaligned.h>

// #define	DEBUG			// error path messages, extra info
// #define	VERBOSE			// more; success messages
// #define	REALLY_QUEUE

#if !defined (DEBUG) && defined (CONFIG_USB_DEBUG)
#   define DEBUG
#endif
#include <linux/usb.h>

/* in 2.5 these standard usb ops take mem_flags */
#define ALLOC_URB(n,flags)	usb_alloc_urb(n)
#define SUBMIT_URB(u,flags)	usb_submit_urb(u)

/* and these got renamed (may move to usb.h) */
#define usb_get_dev		usb_inc_dev_use
#define usb_put_dev		usb_dec_dev_use


/* minidrivers _could_ be individually configured */
#define	CONFIG_USB_AN2720
#define	CONFIG_USB_AX8817X
#define	CONFIG_USB_BELKIN
#define	CONFIG_USB_EPSON2888
#define	CONFIG_USB_GENESYS
#define CONFIG_USB_MCS7830
#define	CONFIG_USB_NET1080
#define	CONFIG_USB_PL2301
#define	CONFIG_USB_ARMLINUX
#define	CONFIG_USB_ZAURUS


#define DRIVER_VERSION		"18-Oct-2002"

/*-------------------------------------------------------------------------*/

/*
 * Nineteen USB 1.1 max size bulk transactions per frame (ms), max.
 * Several dozen bytes of IPv4 data can fit in two such transactions.
 * One maximum size Ethernet packet takes twenty four of them.
 * For high speed, each frame comfortably fits almost 36 max size
 * Ethernet packets (so queues should be bigger).
 */
#ifdef REALLY_QUEUE
#define	RX_QLEN		4
#define	TX_QLEN		4
#else
#define	RX_QLEN		1
#define	TX_QLEN		1
#endif

// packets are always ethernet inside
// ... except they can be bigger (limit of 64K with NetChip framing)
#define MIN_PACKET	sizeof(struct ethhdr)
#define MAX_PACKET	32768

// reawaken network queue this soon after stopping; else watchdog barks
#define TX_TIMEOUT_JIFFIES	(5*HZ)

// for vendor-specific control operations
#define	CONTROL_TIMEOUT_MS	(500)			/* msec */
#define CONTROL_TIMEOUT_JIFFIES ((CONTROL_TIMEOUT_MS * HZ)/1000)

// between wakeups
#define UNLINK_TIMEOUT_JIFFIES ((3  /*ms*/ * HZ)/1000)

/*-------------------------------------------------------------------------*/

// list of all devices we manage
static DECLARE_MUTEX (usbnet_mutex);
static LIST_HEAD (usbnet_list);

// randomly generated ethernet address
static u8	node_id [ETH_ALEN];

// state we keep for each device we handle
struct usbnet {
	// housekeeping
	struct usb_device	*udev;
	struct driver_info	*driver_info;
	struct semaphore	mutex;
	struct semaphore	phy_mutex;
	unsigned		ifnum;
	struct list_head	dev_list;
	wait_queue_head_t	*wait;

	// i/o info: pipes etc
	unsigned		in, out;
	unsigned		maxpacket;
	//struct timer_list	delay;

	// protocol/interface state
	struct net_device	net;
	struct net_device_stats	stats;
	int			msg_level;
	struct mii_if_info	mii;

#ifdef CONFIG_USB_NET1080
	u16			packet_id;
#endif

	// various kinds of pending driver work
	struct sk_buff_head	rxq;
	struct sk_buff_head	txq;
	struct sk_buff_head	done;
	struct tasklet_struct	bh;

	struct tq_struct	kevent;
	unsigned long		flags;
#		define EVENT_TX_HALT	0
#		define EVENT_RX_HALT	1
#		define EVENT_RX_MEMORY	2
};

// device-specific info used by the driver
struct driver_info {
	char		*description;

	int		flags;
#define FLAG_FRAMING_NC	0x0001		/* guard against device dropouts */ 
#define FLAG_FRAMING_GL	0x0002		/* genelink batches packets */
#define FLAG_FRAMING_Z	0x0004		/* zaurus adds a trailer */
#define FLAG_NO_SETINT	0x0010		/* device can't set_interface() */
#define FLAG_ETHER	0x0020		/* maybe use "eth%d" names */
#define FLAG_RX_ONEMORE 0x0040		/* add one to rx urb size */

	/* init device ... can sleep, or cause probe() failure */
	int	(*bind)(struct usbnet *, struct usb_device *);

	/* reset device ... can sleep */
	int	(*reset)(struct usbnet *);

	/* see if peer is connected ... can sleep */
	int	(*check_connect)(struct usbnet *);

	/* fixup rx packet (strip framing) */
	int	(*rx_fixup)(struct usbnet *dev, struct sk_buff *skb);

	/* fixup tx packet (add framing) */
	struct sk_buff	*(*tx_fixup)(struct usbnet *dev,
				struct sk_buff *skb, int flags);

	// FIXME -- also an interrupt mechanism
	// useful for at least PL2301/2302 and GL620USB-A

	/* for new devices, use the descriptor-reading code instead */
	int		in;		/* rx endpoint */
	int		out;		/* tx endpoint */
	int		epsize;

	unsigned long	data;		/* Misc driver specific data */
};

// we record the state for each of our queued skbs
enum skb_state {
	illegal = 0,
	tx_start, tx_done,
	rx_start, rx_done, rx_cleanup
};

struct skb_data {	// skb->cb is one of these
	struct urb		*urb;
	struct usbnet		*dev;
	enum skb_state		state;
	size_t			length;
};

static const char driver_name [] = "usbnet";

/* use ethtool to change the level for any given device */
static int msg_level = 1;
MODULE_PARM (msg_level, "i");
MODULE_PARM_DESC (msg_level, "Initial message level (default = 1)");


#define	mutex_lock(x)	down(x)
#define	mutex_unlock(x)	up(x)

#define	RUN_CONTEXT (in_irq () ? "in_irq" \
			: (in_interrupt () ? "in_interrupt" : "can sleep"))

static struct ethtool_ops usbnet_ethtool_ops;

/* mostly for PDA style devices, which are always present */
static int always_connected (struct usbnet *dev)
{
	return 0;
}

/*-------------------------------------------------------------------------*/

/* handles CDC Ethernet and many other network "bulk data" interfaces */
static int
get_endpoints (struct usbnet *dev, struct usb_interface *intf)
{
	int				tmp;
	struct usb_interface_descriptor	*alt;
	struct usb_endpoint_descriptor	*in, *out;

	for (tmp = 0; tmp < intf->max_altsetting; tmp++) {
		unsigned	ep;

		in = out = 0;
		alt = intf->altsetting + tmp;

		/* take the first altsetting with in-bulk + out-bulk;
		 * ignore other endpoints and altsetttings.
		 */
		for (ep = 0; ep < alt->bNumEndpoints; ep++) {
			struct usb_endpoint_descriptor	*e;

			e = alt->endpoint + ep;
			if (e->bmAttributes != USB_ENDPOINT_XFER_BULK)
				continue;
			if (e->bEndpointAddress & USB_DIR_IN) {
				if (!in)
					in = e;
			} else {
				if (!out)
					out = e;
			}
			if (in && out)
				goto found;
		}
	}
	return -EINVAL;

found:
	if (alt->bAlternateSetting != 0
			|| !(dev->driver_info->flags & FLAG_NO_SETINT)) {
		tmp = usb_set_interface (dev->udev, alt->bInterfaceNumber,
				alt->bAlternateSetting);
		if (tmp < 0)
			return tmp;
	}
	
	dev->in = usb_rcvbulkpipe (dev->udev,
			in->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK);
	dev->out = usb_sndbulkpipe (dev->udev,
			out->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK);
	dev->maxpacket = usb_maxpacket (dev->udev, dev->out, 1);
	return 0;
}

/*-------------------------------------------------------------------------*/

#ifdef DEBUG
#define devdbg(usbnet, fmt, arg...) \
	printk(KERN_DEBUG "%s: " fmt "\n" , (usbnet)->net.name , ## arg)
#else
#define devdbg(usbnet, fmt, arg...) do {} while(0)
#endif

#define devinfo(usbnet, fmt, arg...) \
	do { if ((usbnet)->msg_level >= 1) \
	printk(KERN_INFO "%s: " fmt "\n" , (usbnet)->net.name , ## arg); \
	} while (0)



#ifdef	CONFIG_USB_MCS7830
#include"mcs7830.c"
#endif


#ifdef	CONFIG_USB_AN2720

/*-------------------------------------------------------------------------
 *
 * AnchorChips 2720 driver ... http://www.cypress.com
 *
 * This doesn't seem to have a way to detect whether the peer is
 * connected, or need any reset handshaking.  It's got pretty big
 * internal buffers (handles most of a frame's worth of data).
 * Chip data sheets don't describe any vendor control messages.
 *
 *-------------------------------------------------------------------------*/

static const struct driver_info	an2720_info = {
	.description =	"AnchorChips/Cypress 2720",
	// no reset available!
	// no check_connect available!

	.in = 2, .out = 2,		// direction distinguishes these
	.epsize =64,
};

#endif	/* CONFIG_USB_AN2720 */


#ifdef CONFIG_USB_AX8817X
/* ASIX AX8817X based USB 2.0 Ethernet Devices */

#define HAVE_HARDWARE
#define NEED_MII

#include <linux/crc32.h>

#define AX_CMD_SET_SW_MII		0x06
#define AX_CMD_READ_MII_REG		0x07
#define AX_CMD_WRITE_MII_REG		0x08
#define AX_CMD_SET_HW_MII		0x0a
#define AX_CMD_WRITE_RX_CTL		0x10
#define AX_CMD_READ_IPG012		0x11
#define AX_CMD_WRITE_IPG0		0x12
#define AX_CMD_WRITE_IPG1		0x13
#define AX_CMD_WRITE_IPG2		0x14
#define AX_CMD_WRITE_MULTI_FILTER	0x16
#define AX_CMD_READ_NODE_ID		0x17
#define AX_CMD_READ_PHY_ID		0x19
#define AX_CMD_WRITE_MEDIUM_MODE	0x1b
#define AX_CMD_WRITE_GPIOS		0x1f

#define AX_MCAST_FILTER_SIZE		8
#define AX_MAX_MCAST			64

static int ax8817x_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
			    u16 size, void *data)
{
	return usb_control_msg(
		dev->udev,
		usb_rcvctrlpipe(dev->udev, 0),
		cmd,
		USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
		value,
		index,
		data,
		size,
		CONTROL_TIMEOUT_JIFFIES);
}

static int ax8817x_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index,
			     u16 size, void *data)
{
	return usb_control_msg(
		dev->udev,
		usb_sndctrlpipe(dev->udev, 0),
		cmd,
		USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
		value,
		index,
		data,
		size,
		CONTROL_TIMEOUT_JIFFIES);
}

static void ax8817x_async_cmd_callback(struct urb *urb)
{
	struct usb_ctrlrequest *req = (struct usb_ctrlrequest *)urb->context;

	if (urb->status < 0)
		printk(KERN_DEBUG "ax8817x_async_cmd_callback() failed with %d",
			urb->status);

	kfree(req);
	usb_free_urb(urb);
}

static void ax8817x_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value, u16 index,
				    u16 size, void *data)
{
	struct usb_ctrlrequest *req;
	int status;
	struct urb *urb;

	if ((urb = ALLOC_URB(0, GFP_ATOMIC)) == NULL) {
		devdbg(dev, "Error allocating URB in write_cmd_async!");
		return;
	}

	if ((req = kmalloc(sizeof(struct usb_ctrlrequest), GFP_ATOMIC)) == NULL) {
		devdbg(dev, "Failed to allocate memory for control request");
		usb_free_urb(urb);
		return;
	}

	req->bRequestType = USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE;
	req->bRequest = cmd;
	req->wValue = cpu_to_le16(value);
	req->wIndex = cpu_to_le16(index); 
	req->wLength = cpu_to_le16(size);

	usb_fill_control_urb(urb, dev->udev,
			     usb_sndctrlpipe(dev->udev, 0),
			     (void *)req, data, size,
			     ax8817x_async_cmd_callback, req);

	if((status = SUBMIT_URB(urb, GFP_ATOMIC)) < 0)
		devdbg(dev, "Error submitting the control message: status=%d", status);
}

static void ax8817x_set_multicast(struct net_device *net)
{
	struct usbnet *dev = (struct usbnet *) net->priv;
	u8 rx_ctl = 0x8c;

	if (net->flags & IFF_PROMISC) {
		rx_ctl |= 0x01;
	} else if (net->flags & IFF_ALLMULTI
		   || net->mc_count > AX_MAX_MCAST) {
		rx_ctl |= 0x02;
	} else if (net->mc_count == 0) {
		/* just broadcast and directed */
	} else {
		struct dev_mc_list *mc_list = net->mc_list;
		u8 *multi_filter;
		u32 crc_bits;
		int i;

		multi_filter = kmalloc(AX_MCAST_FILTER_SIZE, GFP_ATOMIC);
		if (multi_filter == NULL) {
			/* Oops, couldn't allocate a buffer for setting the multicast
			   filter. Try all multi mode. */
			rx_ctl |= 0x02;
		} else {
			memset(multi_filter, 0, AX_MCAST_FILTER_SIZE);

			/* Build the multicast hash filter. */
			for (i = 0; i < net->mc_count; i++) {
				crc_bits =
				    ether_crc(ETH_ALEN,
					      mc_list->dmi_addr) >> 26;
				multi_filter[crc_bits >> 3] |=
				    1 << (crc_bits & 7);
				mc_list = mc_list->next;
			}

			ax8817x_write_cmd_async(dev, AX_CMD_WRITE_MULTI_FILTER, 0, 0,
					   AX_MCAST_FILTER_SIZE, multi_filter);

			rx_ctl |= 0x10;
		}
	}

	ax8817x_write_cmd_async(dev, AX_CMD_WRITE_RX_CTL, rx_ctl, 0, 0, NULL);
}

static int ax8817x_mdio_read(struct net_device *netdev, int phy_id, int loc)
{
	struct usbnet *dev = netdev->priv;
	u16 res;
	u8 buf[4];

	ax8817x_write_cmd(dev, AX_CMD_SET_SW_MII, 0, 0, 0, &buf);
	ax8817x_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id, (__u16)loc, 2, (u16 *)&res);
	ax8817x_write_cmd(dev, AX_CMD_SET_HW_MII, 0, 0, 0, &buf);

	return res & 0xffff;
}

static void ax8817x_mdio_write(struct net_device *netdev, int phy_id, int loc, int val)
{
	struct usbnet *dev = netdev->priv;
	u16 res = val;
	u8 buf[4];

	ax8817x_write_cmd(dev, AX_CMD_SET_SW_MII, 0, 0, 0, &buf);
	ax8817x_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id, (__u16)loc, 2, (u16 *)&res);
	ax8817x_write_cmd(dev, AX_CMD_SET_HW_MII, 0, 0, 0, &buf);
}

static int ax8817x_bind(struct usbnet *dev, struct usb_device *intf)
{
	int ret;
	u8 buf[6];
	u16 *buf16 = (u16 *) buf;
	int i;
	unsigned long gpio_bits = dev->driver_info->data;

	dev->in = usb_rcvbulkpipe(dev->udev, 3);
	dev->out = usb_sndbulkpipe(dev->udev, 2);

	/* Toggle the GPIOs in a manufacturer/model specific way */
	for (i = 2; i >= 0; i--) {
		if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_GPIOS,
				       (gpio_bits >> (i * 8)) & 0xff, 0, 0,
				       buf)) < 0)
			return ret;
		wait_ms(5);
	}

	if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_RX_CTL, 0x80, 0, 0, buf)) < 0) {
		dbg("send AX_CMD_WRITE_RX_CTL failed: %d", ret);
		return ret;
	}

	/* Get the MAC address */
	memset(buf, 0, ETH_ALEN);
	if ((ret = ax8817x_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, 6, buf)) < 0) {
		dbg("read AX_CMD_READ_NODE_ID failed: %d", ret);
		return ret;
	}
	memcpy(dev->net.dev_addr, buf, ETH_ALEN);

	/* Get IPG values */
	if ((ret = ax8817x_read_cmd(dev, AX_CMD_READ_IPG012, 0, 0, 3, buf)) < 0) {
		dbg("Error reading IPG values: %d", ret);
		return ret;
	}

	for(i = 0;i < 3;i++) {
		ax8817x_write_cmd(dev, AX_CMD_WRITE_IPG0 + i, 0, 0, 1, &buf[i]);
	}

	/* Get the PHY id */
	if ((ret = ax8817x_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf)) < 0) {
		dbg("error on read AX_CMD_READ_PHY_ID: %02x", ret);
		return ret;
	} else if (ret < 2) {
		/* this should always return 2 bytes */
		dbg("AX_CMD_READ_PHY_ID returned less than 2 bytes: ret=%02x", ret);
		return -EIO;
	}

	/* Initialize MII structure */
	dev->mii.dev = &dev->net;
	dev->mii.mdio_read = ax8817x_mdio_read;
	dev->mii.mdio_write = ax8817x_mdio_write;
	dev->mii.phy_id_mask = 0x3f;
	dev->mii.reg_num_mask = 0x1f;
	dev->mii.phy_id = buf[1];

	if ((ret = ax8817x_write_cmd(dev, AX_CMD_SET_SW_MII, 0, 0, 0, &buf)) < 0) {
		dbg("Failed to go to software MII mode: %02x", ret);
		return ret;
	}

	*buf16 = cpu_to_le16(BMCR_RESET);
	if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_MII_REG,
				     dev->mii.phy_id, MII_BMCR, 2, buf16)) < 0) {
		dbg("Failed to write MII reg - MII_BMCR: %02x", ret);
		return ret;
	}

	/* Advertise that we can do full-duplex pause */
	*buf16 = cpu_to_le16(ADVERTISE_ALL | ADVERTISE_CSMA | 0x0400);
	if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_MII_REG,
			   	     dev->mii.phy_id, MII_ADVERTISE, 
				     2, buf16)) < 0) {
		dbg("Failed to write MII_REG advertisement: %02x", ret);
		return ret;
	}

	*buf16 = cpu_to_le16(BMCR_ANENABLE | BMCR_ANRESTART);
	if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_MII_REG,
			  	     dev->mii.phy_id, MII_BMCR, 
				     2, buf16)) < 0) {
		dbg("Failed to write MII reg autonegotiate: %02x", ret);
		return ret;
	}

	if ((ret = ax8817x_write_cmd(dev, AX_CMD_SET_HW_MII, 0, 0, 0, &buf)) < 0) {
		dbg("Failed to set hardware MII: %02x", ret);
		return ret;
	}

	dev->net.set_multicast_list = ax8817x_set_multicast;

	return 0;
}

static const struct driver_info ax8817x_info = {
	.description = "ASIX AX8817x USB 2.0 Ethernet",
	.bind = ax8817x_bind,
	.flags =  FLAG_ETHER,
	.data = 0x00130103,
};

static const struct driver_info dlink_dub_e100_info = {
	.description = "DLink DUB-E100 USB Ethernet",
	.bind = ax8817x_bind,
	.flags =  FLAG_ETHER,
	.data = 0x009f9d9f,
};

static const struct driver_info netgear_fa120_info = {
	.description = "Netgear FA-120 USB Ethernet",
	.bind = ax8817x_bind,
	.flags =  FLAG_ETHER,
	.data = 0x00130103,
};

static const struct driver_info hawking_uf200_info = {
	.description = "Hawking UF200 USB Ethernet",
	.bind = ax8817x_bind,
	.flags =  FLAG_ETHER,
	.data = 0x001f1d1f,
};
#endif /* CONFIG_USB_AX8817X */


#ifdef	CONFIG_USB_BELKIN

/*-------------------------------------------------------------------------
 *
 * Belkin F5U104 ... two NetChip 2280 devices + Atmel microcontroller
 *
 * ... also two eTEK designs, including one sold as "Advance USBNET"
 *
 *-------------------------------------------------------------------------*/

static const struct driver_info	belkin_info = {
	.description =	"Belkin, eTEK, or compatible",
};

#endif	/* CONFIG_USB_BELKIN */



#ifdef	CONFIG_USB_EPSON2888

/*-------------------------------------------------------------------------
 *
 * EPSON USB clients
 *
 * This is the same idea as Linux PDAs (below) except the firmware in the
 * device might not be Tux-powered.  Epson provides reference firmware that
 * implements this interface.  Product developers can reuse or modify that
 * code, such as by using their own product and vendor codes.
 *
 *-------------------------------------------------------------------------*/

static const struct driver_info	epson2888_info = {
	.description =	"Epson USB Device",
	.check_connect = always_connected,

	.in = 4, .out = 3,
	.epsize = 64,
};

#endif	/* CONFIG_USB_EPSON2888 */


#ifdef CONFIG_USB_GENESYS

/*-------------------------------------------------------------------------
 *
 * GeneSys GL620USB-A (www.genesyslogic.com.tw)
 *
 * ... should partially interop with the Win32 driver for this hardware
 * The GeneSys docs imply there's some NDIS issue motivating this framing.
 *
 * Some info from GeneSys:
 *  - GL620USB-A is full duplex; GL620USB is only half duplex for bulk.
 *    (Some cables, like the BAFO-100c, use the half duplex version.)
 *  - For the full duplex model, the low bit of the version code says
 *    which side is which ("left/right").
 *  - For the half duplex type, a control/interrupt handshake settles
 *    the transfer direction.  (That's disabled here, partially coded.)
 *    A control URB would block until other side writes an interrupt.
 *
 *-------------------------------------------------------------------------*/

// control msg write command
#define GENELINK_CONNECT_WRITE			0xF0
// interrupt pipe index
#define GENELINK_INTERRUPT_PIPE			0x03
// interrupt read buffer size
#define INTERRUPT_BUFSIZE			0x08
// interrupt pipe interval value
#define GENELINK_INTERRUPT_INTERVAL		0x10
// max transmit packet number per transmit
#define GL_MAX_TRANSMIT_PACKETS			32
// max packet length
#define GL_MAX_PACKET_LEN			1514
// max receive buffer size 
#define GL_RCV_BUF_SIZE		\
	(((GL_MAX_PACKET_LEN + 4) * GL_MAX_TRANSMIT_PACKETS) + 4)

struct gl_packet {
	u32		packet_length;
	char		packet_data [1];
};

struct gl_header {
	u32			packet_count;
	struct gl_packet	packets;
};

#ifdef	GENLINK_ACK

// FIXME:  this code is incomplete, not debugged; it doesn't
// handle interrupts correctly.  interrupts should be generic
// code like all other device I/O, anyway.

struct gl_priv { 
	struct urb	*irq_urb;
	char		irq_buf [INTERRUPT_BUFSIZE];
};

static inline int gl_control_write (struct usbnet *dev, u8 request, u16 value)
{
	int retval;

	retval = usb_control_msg (dev->udev,
		      usb_sndctrlpipe (dev->udev, 0),
		      request,
		      USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE,
		      value, 
		      0,			// index
		      0,			// data buffer
		      0,			// size
		      CONTROL_TIMEOUT_JIFFIES);
	return retval;
}

static void gl_interrupt_complete (struct urb *urb)
{
	int status = urb->status;
	
	switch (status) {
	case 0:
		/* success */
		break;
	case -ECONNRESET:
	case -ENOENT:
	case -ESHUTDOWN:
		/* this urb is terminated, clean up */
		dbg("%s - urb shutting down with status: %d",
				__FUNCTION__, status);
		return;
	default:
		dbg("%s - nonzero urb status received: %d",
				__FUNCTION__, urb->status);
	}

	// NOTE:  2.4 still has automagic resubmit, so this would be
	// wrong ... but this code has never worked, is always disabled.
	status = usb_submit_urb (urb, GFP_ATOMIC);
	if (status)
		err ("%s - usb_submit_urb failed with result %d",
		     __FUNCTION__, status);
}

static int gl_interrupt_read (struct usbnet *dev)
{
	struct gl_priv	*priv = dev->priv_data;
	int		retval;

	// issue usb interrupt read
	if (priv && priv->irq_urb) {
		// submit urb
		if ((retval = SUBMIT_URB (priv->irq_urb, GFP_KERNEL)) != 0)
			dbg ("gl_interrupt_read: submit fail - %X...", retval);
		else
			dbg ("gl_interrupt_read: submit success...");
	}

	return 0;
}

// check whether another side is connected
static int genelink_check_connect (struct usbnet *dev)
{
	int			retval;

	dbg ("genelink_check_connect...");

	// detect whether another side is connected
	if ((retval = gl_control_write (dev, GENELINK_CONNECT_WRITE, 0)) != 0) {
		dbg ("%s: genelink_check_connect write fail - %X",
			dev->net.name, retval);
		return retval;
	}

	// usb interrupt read to ack another side 
	if ((retval = gl_interrupt_read (dev)) != 0) {
		dbg ("%s: genelink_check_connect read fail - %X",
			dev->net.name, retval);
		return retval;
	}

	dbg ("%s: genelink_check_connect read success", dev->net.name);
	return 0;
}

// allocate and initialize the private data for genelink
static int genelink_init (struct usbnet *dev)
{
	struct gl_priv *priv;

	// allocate the private data structure
	if ((priv = kmalloc (sizeof *priv, GFP_KERNEL)) == 0) {
		dbg ("%s: cannot allocate private data per device",
			dev->net.name);
		return -ENOMEM;
	}

	// allocate irq urb
	if ((priv->irq_urb = ALLOC_URB (0, GFP_KERNEL)) == 0) {
		dbg ("%s: cannot allocate private irq urb per device",
			dev->net.name);
		kfree (priv);
		return -ENOMEM;
	}

	// fill irq urb
	usb_fill_int_urb (priv->irq_urb, dev->udev,
		usb_rcvintpipe (dev->udev, GENELINK_INTERRUPT_PIPE),
		priv->irq_buf, INTERRUPT_BUFSIZE,
		gl_interrupt_complete, 0,
		GENELINK_INTERRUPT_INTERVAL);

	// set private data pointer
	dev->priv_data = priv;

	return 0;
}

// release the private data
static int genelink_free (struct usbnet *dev)
{
	struct gl_priv	*priv = dev->priv_data;

	if (!priv) 
		return 0;

// FIXME:  can't cancel here; it's synchronous, and
// should have happened earlier in any case (interrupt
// handling needs to be generic)

	// cancel irq urb first
	usb_unlink_urb (priv->irq_urb);

	// free irq urb
	usb_free_urb (priv->irq_urb);

	// free the private data structure
	kfree (priv);

	return 0;
}

#endif

static int genelink_rx_fixup (struct usbnet *dev, struct sk_buff *skb)
{
	struct gl_header	*header;
	struct gl_packet	*packet;
	struct sk_buff		*gl_skb;
	int			status;
	u32			size;

	header = (struct gl_header *) skb->data;

	// get the packet count of the received skb
	le32_to_cpus (&header->packet_count);
	if ((header->packet_count > GL_MAX_TRANSMIT_PACKETS)
			|| (header->packet_count < 0)) {
		dbg ("genelink: illegal received packet count %d",
			header->packet_count);
		return 0;
	}

	// set the current packet pointer to the first packet
	packet = &header->packets;

	// decrement the length for the packet count size 4 bytes
	skb_pull (skb, 4);

	while (header->packet_count > 1) {
		// get the packet length
		size = packet->packet_length;

		// this may be a broken packet
		if (size > GL_MAX_PACKET_LEN) {
			dbg ("genelink: illegal rx length %d", size);
			return 0;
		}

		// allocate the skb for the individual packet
		gl_skb = alloc_skb (size, GFP_ATOMIC);
		if (gl_skb) {

			// copy the packet data to the new skb
			memcpy (gl_skb->data, packet->packet_data, size);

			// set skb data size
			gl_skb->len = size;
			gl_skb->dev = &dev->net;

			// determine the packet's protocol ID
			gl_skb->protocol = eth_type_trans (gl_skb, &dev->net);

			// update the status
			dev->stats.rx_packets++;
			dev->stats.rx_bytes += size;

			// notify os of the received packet
			status = netif_rx (gl_skb);
		}

		// advance to the next packet
		packet = (struct gl_packet *)
			&packet->packet_data [size];
		header->packet_count--;

		// shift the data pointer to the next gl_packet
		skb_pull (skb, size + 4);
	}

	// skip the packet length field 4 bytes
	skb_pull (skb, 4);

	if (skb->len > GL_MAX_PACKET_LEN) {
		dbg ("genelink: illegal rx length %d", skb->len);
		return 0;
	}
	return 1;
}

static struct sk_buff *
genelink_tx_fixup (struct usbnet *dev, struct sk_buff *skb, int flags)
{
	int 	padlen;
	int	length = skb->len;
	int	headroom = skb_headroom (skb);
	int	tailroom = skb_tailroom (skb);
	u32	*packet_count;
	u32	*packet_len;

	// FIXME:  magic numbers, bleech
	padlen = ((skb->len + (4 + 4*1)) % 64) ? 0 : 1;

	if ((!skb_cloned (skb))
			&& ((headroom + tailroom) >= (padlen + (4 + 4*1)))) {
		if ((headroom < (4 + 4*1)) || (tailroom < padlen)) {
			skb->data = memmove (skb->head + (4 + 4*1),
					     skb->data, skb->len);
			skb->tail = skb->data + skb->len;
		}
	} else {
		struct sk_buff	*skb2;
		skb2 = skb_copy_expand (skb, (4 + 4*1) , padlen, flags);
		dev_kfree_skb_any (skb);
		skb = skb2;
	}

	// attach the packet count to the header
	packet_count = (u32 *) skb_push (skb, (4 + 4*1));
	packet_len = packet_count + 1;

	// FIXME little endian?
	*packet_count = 1;
	*packet_len = length;

	// add padding byte
	if ((skb->len % dev->maxpacket) == 0)
		skb_put (skb, 1);

	return skb;
}

static const struct driver_info	genelink_info = {
	.description =	"Genesys GeneLink",
	.flags =	FLAG_FRAMING_GL | FLAG_NO_SETINT,
	.rx_fixup =	genelink_rx_fixup,
	.tx_fixup =	genelink_tx_fixup,

	.in = 1, .out = 2,
	.epsize =64,

#ifdef	GENELINK_ACK
	.check_connect =genelink_check_connect,
#endif
};

#endif /* CONFIG_USB_GENESYS */



#ifdef	CONFIG_USB_NET1080

/*-------------------------------------------------------------------------
 *
 * Netchip 1080 driver ... http://www.netchip.com
 * Used in LapLink cables
 *
 *-------------------------------------------------------------------------*/

/*
 * NetChip framing of ethernet packets, supporting additional error
 * checks for links that may drop bulk packets from inside messages.
 * Odd USB length == always short read for last usb packet.
 *	- nc_header
 *	- Ethernet header (14 bytes)
 *	- payload
 *	- (optional padding byte, if needed so length becomes odd)
 *	- nc_trailer
 *
 * This framing is to be avoided for non-NetChip devices.
 */

struct nc_header {		// packed:
	u16	hdr_len;		// sizeof nc_header (LE, all)
	u16	packet_len;		// payload size (including ethhdr)
	u16	packet_id;		// detects dropped packets
#define MIN_HEADER	6

	// all else is optional, and must start with:
	// u16	vendorId;		// from usb-if
	// u16	productId;
} __attribute__((__packed__));

#define	PAD_BYTE	((unsigned char)0xAC)

struct nc_trailer {
	u16	packet_id;
} __attribute__((__packed__));

// packets may use FLAG_FRAMING_NC and optional pad
#define FRAMED_SIZE(mtu) (sizeof (struct nc_header) \
				+ sizeof (struct ethhdr) \
				+ (mtu) \
				+ 1 \
				+ sizeof (struct nc_trailer))

#define MIN_FRAMED	FRAMED_SIZE(0)


/*
 * Zero means no timeout; else, how long a 64 byte bulk packet may be queued
 * before the hardware drops it.  If that's done, the driver will need to
 * frame network packets to guard against the dropped USB packets.  The win32
 * driver sets this for both sides of the link.
 */
#define	NC_READ_TTL_MS	((u8)255)	// ms

/*
 * We ignore most registers and EEPROM contents.
 */
#define	REG_USBCTL	((u8)0x04)
#define REG_TTL		((u8)0x10)
#define REG_STATUS	((u8)0x11)

/*
 * Vendor specific requests to read/write data
 */
#define	REQUEST_REGISTER	((u8)0x10)
#define	REQUEST_EEPROM		((u8)0x11)

static int
nc_vendor_read (struct usbnet *dev, u8 req, u8 regnum, u16 *retval_ptr)
{
	int status = usb_control_msg (dev->udev,
		usb_rcvctrlpipe (dev->udev, 0),
		req,
		USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
		0, regnum,
		retval_ptr, sizeof *retval_ptr,
		CONTROL_TIMEOUT_JIFFIES);
	if (status > 0)
		status = 0;
	if (!status)
		le16_to_cpus (retval_ptr);
	return status;
}

static inline int
nc_register_read (struct usbnet *dev, u8 regnum, u16 *retval_ptr)
{
	return nc_vendor_read (dev, REQUEST_REGISTER, regnum, retval_ptr);
}

// no retval ... can become async, usable in_interrupt()
static void
nc_vendor_write (struct usbnet *dev, u8 req, u8 regnum, u16 value)
{
	usb_control_msg (dev->udev,
		usb_sndctrlpipe (dev->udev, 0),
		req,
		USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
		value, regnum,
		0, 0,			// data is in setup packet
		CONTROL_TIMEOUT_JIFFIES);
}

static inline void
nc_register_write (struct usbnet *dev, u8 regnum, u16 value)
{
	nc_vendor_write (dev, REQUEST_REGISTER, regnum, value);
}


#if 0
static void nc_dump_registers (struct usbnet *dev)
{
	u8	reg;
	u16	*vp = kmalloc (sizeof (u16));

	if (!vp) {
		dbg ("no memory?");
		return;
	}

	dbg ("%s registers:", dev->net.name);
	for (reg = 0; reg < 0x20; reg++) {
		int retval;

		// reading some registers is trouble
		if (reg >= 0x08 && reg <= 0xf)
			continue;
		if (reg >= 0x12 && reg <= 0x1e)
			continue;

		retval = nc_register_read (dev, reg, vp);
		if (retval < 0)
			dbg ("%s reg [0x%x] ==> error %d",
				dev->net.name, reg, retval);
		else
			dbg ("%s reg [0x%x] = 0x%x",
				dev->net.name, reg, *vp);
	}
	kfree (vp);
}
#endif


/*-------------------------------------------------------------------------*/

/*
 * Control register
 */

#define	USBCTL_WRITABLE_MASK	0x1f0f
// bits 15-13 reserved, r/o
#define	USBCTL_ENABLE_LANG	(1 << 12)
#define	USBCTL_ENABLE_MFGR	(1 << 11)
#define	USBCTL_ENABLE_PROD	(1 << 10)
#define	USBCTL_ENABLE_SERIAL	(1 << 9)
#define	USBCTL_ENABLE_DEFAULTS	(1 << 8)
// bits 7-4 reserved, r/o
#define	USBCTL_FLUSH_OTHER	(1 << 3)
#define	USBCTL_FLUSH_THIS	(1 << 2)
#define	USBCTL_DISCONN_OTHER	(1 << 1)
#define	USBCTL_DISCONN_THIS	(1 << 0)

static inline void nc_dump_usbctl (struct usbnet *dev, u16 usbctl)
{
#ifdef DEBUG
	devdbg (dev, "net1080 %s-%s usbctl 0x%x:%s%s%s%s%s;"
			" this%s%s;"
			" other%s%s; r/o 0x%x",
		dev->udev->bus->bus_name, dev->udev->devpath,
		usbctl,
		(usbctl & USBCTL_ENABLE_LANG) ? " lang" : "",
		(usbctl & USBCTL_ENABLE_MFGR) ? " mfgr" : "",
		(usbctl & USBCTL_ENABLE_PROD) ? " prod" : "",
		(usbctl & USBCTL_ENABLE_SERIAL) ? " serial" : "",
		(usbctl & USBCTL_ENABLE_DEFAULTS) ? " defaults" : "",

		(usbctl & USBCTL_FLUSH_OTHER) ? " FLUSH" : "",
		(usbctl & USBCTL_DISCONN_OTHER) ? " DIS" : "",
		(usbctl & USBCTL_FLUSH_THIS) ? " FLUSH" : "",
		(usbctl & USBCTL_DISCONN_THIS) ? " DIS" : "",
		usbctl & ~USBCTL_WRITABLE_MASK
		);
#endif
}

/*-------------------------------------------------------------------------*/

/*
 * Status register
 */

#define	STATUS_PORT_A		(1 << 15)

#define	STATUS_CONN_OTHER	(1 << 14)
#define	STATUS_SUSPEND_OTHER	(1 << 13)
#define	STATUS_MAILBOX_OTHER	(1 << 12)
#define	STATUS_PACKETS_OTHER(n)	(((n) >> 8) & 0x03)

#define	STATUS_CONN_THIS	(1 << 6)
#define	STATUS_SUSPEND_THIS	(1 << 5)
#define	STATUS_MAILBOX_THIS	(1 << 4)
#define	STATUS_PACKETS_THIS(n)	(((n) >> 0) & 0x03)

#define	STATUS_UNSPEC_MASK	0x0c8c
#define	STATUS_NOISE_MASK 	((u16)~(0x0303|STATUS_UNSPEC_MASK))


static inline void nc_dump_status (struct usbnet *dev, u16 status)
{
#ifdef DEBUG
	devdbg (dev, "net1080 %s-%s status 0x%x:"
			" this (%c) PKT=%d%s%s%s;"
			" other PKT=%d%s%s%s; unspec 0x%x",
		dev->udev->bus->bus_name, dev->udev->devpath,
		status,

		// XXX the packet counts don't seem right
		// (1 at reset, not 0); maybe UNSPEC too

		(status & STATUS_PORT_A) ? 'A' : 'B',
		STATUS_PACKETS_THIS (status),
		(status & STATUS_CONN_THIS) ? " CON" : "",
		(status & STATUS_SUSPEND_THIS) ? " SUS" : "",
		(status & STATUS_MAILBOX_THIS) ? " MBOX" : "",

		STATUS_PACKETS_OTHER (status),
		(status & STATUS_CONN_OTHER) ? " CON" : "",
		(status & STATUS_SUSPEND_OTHER) ? " SUS" : "",
		(status & STATUS_MAILBOX_OTHER) ? " MBOX" : "",

		status & STATUS_UNSPEC_MASK
		);
#endif
}

/*-------------------------------------------------------------------------*/

/*
 * TTL register
 */

#define	TTL_THIS(ttl)	(0x00ff & ttl)
#define	TTL_OTHER(ttl)	(0x00ff & (ttl >> 8))
#define MK_TTL(this,other)	((u16)(((other)<<8)|(0x00ff&(this))))

static inline void nc_dump_ttl (struct usbnet *dev, u16 ttl)
{
#ifdef DEBUG
	devdbg (dev, "net1080 %s-%s ttl 0x%x this = %d, other = %d",
		dev->udev->bus->bus_name, dev->udev->devpath,
		ttl,

		TTL_THIS (ttl),
		TTL_OTHER (ttl)
		);
#endif
}

/*-------------------------------------------------------------------------*/

static int net1080_reset (struct usbnet *dev)
{
	u16		usbctl, status, ttl;
	u16		*vp = kmalloc (sizeof (u16), GFP_KERNEL);
	int		retval;

	if (!vp)
		return -ENOMEM;

	// nc_dump_registers (dev);

	if ((retval = nc_register_read (dev, REG_STATUS, vp)) < 0) {
		dbg ("can't read %s-%s status: %d",
			dev->udev->bus->bus_name, dev->udev->devpath, retval);
		goto done;
	}
	status = *vp;
	// nc_dump_status (dev, status);

	if ((retval = nc_register_read (dev, REG_USBCTL, vp)) < 0) {
		dbg ("can't read USBCTL, %d", retval);
		goto done;
	}
	usbctl = *vp;
	// nc_dump_usbctl (dev, usbctl);

	nc_register_write (dev, REG_USBCTL,
			USBCTL_FLUSH_THIS | USBCTL_FLUSH_OTHER);

	if ((retval = nc_register_read (dev, REG_TTL, vp)) < 0) {
		dbg ("can't read TTL, %d", retval);
		goto done;
	}
	ttl = *vp;
	// nc_dump_ttl (dev, ttl);

	nc_register_write (dev, REG_TTL,
			MK_TTL (NC_READ_TTL_MS, TTL_OTHER (ttl)) );
	dbg ("%s: assigned TTL, %d ms", dev->net.name, NC_READ_TTL_MS);

	if (dev->msg_level >= 2)
		devinfo (dev, "port %c, peer %sconnected",
			(status & STATUS_PORT_A) ? 'A' : 'B',
			(status & STATUS_CONN_OTHER) ? "" : "dis"
			);
	retval = 0;

done:
	kfree (vp);
	return retval;
}

static int net1080_check_connect (struct usbnet *dev)
{
	int			retval;
	u16			status;
	u16			*vp = kmalloc (sizeof (u16), GFP_KERNEL);

	if (!vp)
		return -ENOMEM;
	retval = nc_register_read (dev, REG_STATUS, vp);
	status = *vp;
	kfree (vp);
	if (retval != 0) {
		dbg ("%s net1080_check_conn read - %d", dev->net.name, retval);
		return retval;
	}
	if ((status & STATUS_CONN_OTHER) != STATUS_CONN_OTHER)
		return -ENOLINK;
	return 0;
}

static int net1080_rx_fixup (struct usbnet *dev, struct sk_buff *skb)
{
	struct nc_header	*header;
	struct nc_trailer	*trailer;

	if (!(skb->len & 0x01)
			|| MIN_FRAMED > skb->len
			|| skb->len > FRAMED_SIZE (dev->net.mtu)) {
		dev->stats.rx_frame_errors++;
		dbg ("rx framesize %d range %d..%d mtu %d", skb->len,
			(int)MIN_FRAMED, (int)FRAMED_SIZE (dev->net.mtu),
			dev->net.mtu);
		return 0;
	}

	header = (struct nc_header *) skb->data;
	le16_to_cpus (&header->hdr_len);
	le16_to_cpus (&header->packet_len);
	if (FRAMED_SIZE (header->packet_len) > MAX_PACKET) {
		dev->stats.rx_frame_errors++;
		dbg ("packet too big, %d", header->packet_len);
		return 0;
	} else if (header->hdr_len < MIN_HEADER) {
		dev->stats.rx_frame_errors++;
		dbg ("header too short, %d", header->hdr_len);
		return 0;
	} else if (header->hdr_len > MIN_HEADER) {
		// out of band data for us?
		dbg ("header OOB, %d bytes",
			header->hdr_len - MIN_HEADER);
		// switch (vendor/product ids) { ... }
	}
	skb_pull (skb, header->hdr_len);

	trailer = (struct nc_trailer *)
		(skb->data + skb->len - sizeof *trailer);
	skb_trim (skb, skb->len - sizeof *trailer);

	if ((header->packet_len & 0x01) == 0) {
		if (skb->data [header->packet_len] != PAD_BYTE) {
			dev->stats.rx_frame_errors++;
			dbg ("bad pad");
			return 0;
		}
		skb_trim (skb, skb->len - 1);
	}
	if (skb->len != header->packet_len) {
		dev->stats.rx_frame_errors++;
		dbg ("bad packet len %d (expected %d)",
			skb->len, header->packet_len);
		return 0;
	}
	if (header->packet_id != get_unaligned (&trailer->packet_id)) {
		dev->stats.rx_fifo_errors++;
		dbg ("(2+ dropped) rx packet_id mismatch 0x%x 0x%x",
			header->packet_id, trailer->packet_id);
		return 0;
	}
#if 0
	devdbg (dev, "frame <rx h %d p %d id %d", header->hdr_len,
		header->packet_len, header->packet_id);
#endif
	return 1;
}

static struct sk_buff *
net1080_tx_fixup (struct usbnet *dev, struct sk_buff *skb, int flags)
{
	int			padlen;
	struct sk_buff		*skb2;

	padlen = ((skb->len + sizeof (struct nc_header)
			+ sizeof (struct nc_trailer)) & 0x01) ? 0 : 1;
	if (!skb_cloned (skb)) {
		int	headroom = skb_headroom (skb);
		int	tailroom = skb_tailroom (skb);

		if ((padlen + sizeof (struct nc_trailer)) <= tailroom
			    && sizeof (struct nc_header) <= headroom)
			return skb;

		if ((sizeof (struct nc_header) + padlen
					+ sizeof (struct nc_trailer)) <
				(headroom + tailroom)) {
			skb->data = memmove (skb->head
						+ sizeof (struct nc_header),
					    skb->data, skb->len);
			skb->tail = skb->data + skb->len;
			return skb;
		}
	}
	skb2 = skb_copy_expand (skb,
				sizeof (struct nc_header),
				sizeof (struct nc_trailer) + padlen,
				flags);
	dev_kfree_skb_any (skb);
	return skb2;
}

static const struct driver_info	net1080_info = {
	.description =	"NetChip TurboCONNECT",
	.flags =	FLAG_FRAMING_NC,
	.reset =	net1080_reset,
	.check_connect =net1080_check_connect,
	.rx_fixup =	net1080_rx_fixup,
	.tx_fixup =	net1080_tx_fixup,
};

#endif /* CONFIG_USB_NET1080 */



#ifdef CONFIG_USB_PL2301

/*-------------------------------------------------------------------------
 *
 * Prolific PL-2301/PL-2302 driver ... http://www.prolifictech.com
 *
 *-------------------------------------------------------------------------*/

/*
 * Bits 0-4 can be used for software handshaking; they're set from
 * one end, cleared from the other, "read" with the interrupt byte.
 */
#define	PL_S_EN		(1<<7)		/* (feature only) suspend enable */
/* reserved bit -- rx ready (6) ? */
#define	PL_TX_READY	(1<<5)		/* (interrupt only) transmit ready */
#define	PL_RESET_OUT	(1<<4)		/* reset output pipe */
#define	PL_RESET_IN	(1<<3)		/* reset input pipe */
#define	PL_TX_C		(1<<2)		/* transmission complete */
#define	PL_TX_REQ	(1<<1)		/* transmission received */
#define	PL_PEER_E	(1<<0)		/* peer exists */

static inline int
pl_vendor_req (struct usbnet *dev, u8 req, u8 val, u8 index)
{
	return usb_control_msg (dev->udev,
		usb_rcvctrlpipe (dev->udev, 0),
		req,
		USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
		val, index,
		0, 0,
		CONTROL_TIMEOUT_JIFFIES);
}

static inline int
pl_clear_QuickLink_features (struct usbnet *dev, int val)
{
	return pl_vendor_req (dev, 1, (u8) val, 0);
}

static inline int
pl_set_QuickLink_features (struct usbnet *dev, int val)
{
	return pl_vendor_req (dev, 3, (u8) val, 0);
}

/*-------------------------------------------------------------------------*/

static int pl_reset (struct usbnet *dev)
{
	return pl_set_QuickLink_features (dev,
		PL_S_EN|PL_RESET_OUT|PL_RESET_IN|PL_PEER_E);
}

static const struct driver_info	prolific_info = {
	.description =	"Prolific PL-2301/PL-2302",
	.flags =	FLAG_NO_SETINT,
		/* some PL-2302 versions seem to fail usb_set_interface() */
	.reset =	pl_reset,
};

#endif /* CONFIG_USB_PL2301 */



#ifdef	CONFIG_USB_ARMLINUX

/*-------------------------------------------------------------------------
 *
 * Standard ARM kernels include a "usb-eth" driver, or a newer
 * "ethernet gadget" driver for basic USB connectivity.  The vendor
 * and product code may also be used for other non-CDC Linux devices,
 * if they all maintain protocol compatibility.
 *
 * That means lots of hardware could match here, possibly using
 * different endpoint numbers (and bcdVersion ids).  so we rely on
 * endpoint descriptors to sort that out for us.
 *
 * (Current Zaurus models need a different driver; see later.)
 *
 *-------------------------------------------------------------------------*/

static const struct driver_info	linuxdev_info = {
	.description =	"Linux Device",
	.check_connect = always_connected,
};

static const struct driver_info	yopy_info = {
	.description =	"Yopy",
	.check_connect = always_connected,
};

static const struct driver_info	blob_info = {
	.description =	"Boot Loader OBject",
	.check_connect = always_connected,
};

#endif	/* CONFIG_USB_ARMLINUX */


#ifdef CONFIG_USB_ZAURUS

#include <linux/crc32.h>

/*-------------------------------------------------------------------------
 *
 * Zaurus PDAs are also ARM based, but currently use different drivers
 * (and framing) for USB slave/gadget controllers than the case above.
 *
 * For the current version of that driver, the main way that framing is
 * nonstandard (also from perspective of the CDC ethernet model!) is a
 * crc32, added to help detect when some sa1100 usb-to-memory DMA errata
 * haven't been fully worked around.
 *
 *-------------------------------------------------------------------------*/

static struct sk_buff *
zaurus_tx_fixup (struct usbnet *dev, struct sk_buff *skb, int flags)
{
	int			padlen;
	struct sk_buff		*skb2;

	padlen = 2;
	if (!skb_cloned (skb)) {
		int	tailroom = skb_tailroom (skb);
		if ((padlen + 4) <= tailroom)
			goto done;
	}
	skb2 = skb_copy_expand (skb, 0, 4 + padlen, flags);
	dev_kfree_skb_any (skb);
	skb = skb2;
	if (skb) {
		u32		fcs;
done:
		fcs = crc32_le (~0, skb->data, skb->len);
		fcs = ~fcs;

		*skb_put (skb, 1) = fcs       & 0xff;
		*skb_put (skb, 1) = (fcs>> 8) & 0xff;
		*skb_put (skb, 1) = (fcs>>16) & 0xff;
		*skb_put (skb, 1) = (fcs>>24) & 0xff;
	}
	return skb;
}

/* SA-1100 based */
static const struct driver_info	zaurus_sl5x00_info = {
	.description =	"Sharp Zaurus SL-5x00",
	.flags =	FLAG_FRAMING_Z,
	.check_connect = always_connected,
	.tx_fixup = 	zaurus_tx_fixup,

	.in = 2, .out = 1,
	.epsize = 64,
};

/* PXA-2xx based */
static const struct driver_info zaurus_pxa_info = {
	.description =	"Sharp Zaurus, PXA-2xx based",
	.flags =	FLAG_FRAMING_Z,
	.check_connect = always_connected,
	.tx_fixup = 	zaurus_tx_fixup,

	.in = 1, .out = 2,
	.epsize = 64,
};

#endif


/*-------------------------------------------------------------------------
 *
 * Network Device Driver (peer link to "Host Device", from USB host)
 *
 *-------------------------------------------------------------------------*/

static int usbnet_change_mtu (struct net_device *net, int new_mtu)
{
	struct usbnet	*dev = (struct usbnet *) net->priv;

	if (new_mtu <= MIN_PACKET || new_mtu > MAX_PACKET)
		return -EINVAL;
#ifdef	CONFIG_USB_NET1080
	if (((dev->driver_info->flags) & FLAG_FRAMING_NC)) {
		if (FRAMED_SIZE (new_mtu) > MAX_PACKET)
			return -EINVAL;
	}
#endif
#ifdef	CONFIG_USB_GENESYS
	if (((dev->driver_info->flags) & FLAG_FRAMING_GL)
			&& new_mtu > GL_MAX_PACKET_LEN)
		return -EINVAL;
#endif
	// no second zero-length packet read wanted after mtu-sized packets
	if (((new_mtu + sizeof (struct ethhdr)) % dev->maxpacket) == 0)
		return -EDOM;
	net->mtu = new_mtu;
	return 0;
}

/*-------------------------------------------------------------------------*/

static struct net_device_stats *usbnet_get_stats (struct net_device *net)
{
	return &((struct usbnet *) net->priv)->stats;
}

/*-------------------------------------------------------------------------*/

/* urb completions may be in_irq; avoid doing real work then. */

static void defer_bh (struct usbnet *dev, struct sk_buff *skb)
{
	struct sk_buff_head	*list = skb->list;
	unsigned long		flags;

	spin_lock_irqsave (&list->lock, flags);
	__skb_unlink (skb, list);
	spin_unlock (&list->lock);
	spin_lock (&dev->done.lock);
	__skb_queue_tail (&dev->done, skb);
	if (dev->done.qlen == 1)
		tasklet_schedule (&dev->bh);
	spin_unlock_irqrestore (&dev->done.lock, flags);
}

/* some work can't be done in tasklets, so we use keventd
 *
 * NOTE:  annoying asymmetry:  if it's active, schedule_task() fails,
 * but tasklet_schedule() doesn't.  hope the failure is rare.
 */
static void defer_kevent (struct usbnet *dev, int work)
{
	set_bit (work, &dev->flags);
	if (!schedule_task (&dev->kevent))
		err ("%s: kevent %d may have been dropped",
			dev->net.name, work);
	else
		dbg ("%s: kevent %d scheduled", dev->net.name, work);
}

/*-------------------------------------------------------------------------*/

static void rx_complete (struct urb *urb);

static void rx_submit (struct usbnet *dev, struct urb *urb, int flags)
{
	struct sk_buff		*skb;
	struct skb_data		*entry;
	int			retval = 0;
	unsigned long		lockflags;
	size_t			size;


#ifdef CONFIG_USB_MCS7830
	if (dev->driver_info->flags & FLAG_RX_ONEMORE)
		size = ETH_FRAME_LEN + 1;
	else
#endif
#ifdef CONFIG_USB_NET1080
	if (dev->driver_info->flags & FLAG_FRAMING_NC)
		size = FRAMED_SIZE (dev->net.mtu);
	else
#endif
#ifdef CONFIG_USB_GENESYS
	if (dev->driver_info->flags & FLAG_FRAMING_GL)
		size = GL_RCV_BUF_SIZE;
	else
#endif
#ifdef CONFIG_USB_ZAURUS
	if (dev->driver_info->flags & FLAG_FRAMING_Z)
		size = 6 + (sizeof (struct ethhdr) + dev->net.mtu);
	else
#endif
		size = (sizeof (struct ethhdr) + dev->net.mtu);

	if ((skb = alloc_skb (size, flags)) == 0) {
		dbg ("no rx skb");
		defer_kevent (dev, EVENT_RX_MEMORY);
		usb_free_urb (urb);
		return;
	}

	entry = (struct skb_data *) skb->cb;
	entry->urb = urb;
	entry->dev = dev;
	entry->state = rx_start;
	entry->length = 0;

	usb_fill_bulk_urb (urb, dev->udev, dev->in,
		skb->data, size, rx_complete, skb);
	urb->transfer_flags |= USB_ASYNC_UNLINK;

	spin_lock_irqsave (&dev->rxq.lock, lockflags);

	if (netif_running (&dev->net)
			&& !test_bit (EVENT_RX_HALT, &dev->flags)) {
		switch (retval = SUBMIT_URB (urb, GFP_ATOMIC)){ 
		case -EPIPE:
			defer_kevent (dev, EVENT_RX_HALT);
			break;
		case -ENOMEM:
			defer_kevent (dev, EVENT_RX_MEMORY);
			break;
		default:
			dbg ("%s rx submit, %d", dev->net.name, retval);
			tasklet_schedule (&dev->bh);
			break;
		case 0:
			__skb_queue_tail (&dev->rxq, skb);
		}
	} else {
		dbg ("rx: stopped");
		retval = -ENOLINK;
	}
	spin_unlock_irqrestore (&dev->rxq.lock, lockflags);
	if (retval) {
		dev_kfree_skb_any (skb);
		usb_free_urb (urb);
	}
}


/*-------------------------------------------------------------------------*/

static inline void rx_process (struct usbnet *dev, struct sk_buff *skb)
{
	if (dev->driver_info->rx_fixup
			&& !dev->driver_info->rx_fixup (dev, skb))
		goto error;
	// else network stack removes extra byte if we forced a short packet

	if (skb->len) {
		int	status;

		skb->dev = &dev->net;
		skb->protocol = eth_type_trans (skb, &dev->net);
		dev->stats.rx_packets++;
		dev->stats.rx_bytes += skb->len;

#ifdef	VERBOSE
		devdbg (dev, "< rx, len %d, type 0x%x",
			skb->len + sizeof (struct ethhdr), skb->protocol);
#endif
		memset (skb->cb, 0, sizeof (struct skb_data));
		status = netif_rx (skb);
		if (status != NET_RX_SUCCESS)
			devdbg (dev, "netif_rx status %d", status);
	} else {
		dbg ("drop");
error:
		dev->stats.rx_errors++;
		skb_queue_tail (&dev->done, skb);
	}
}

/*-------------------------------------------------------------------------*/

static void rx_complete (struct urb *urb)
{
	struct sk_buff		*skb = (struct sk_buff *) urb->context;
	struct skb_data		*entry = (struct skb_data *) skb->cb;
	struct usbnet		*dev = entry->dev;
	int			urb_status = urb->status;

	skb_put (skb, urb->actual_length);
	entry->state = rx_done;
	entry->urb = 0;

	switch (urb_status) {
	    // success
	    case 0:
		if (MIN_PACKET > skb->len || skb->len > MAX_PACKET) {
			entry->state = rx_cleanup;
			dev->stats.rx_errors++;
			dev->stats.rx_length_errors++;
			dbg ("rx length %d", skb->len);
		}
		break;

	    // stalls need manual reset. this is rare ... except that
	    // when going through USB 2.0 TTs, unplug appears this way.
	    // we avoid the highspeed version of the ETIMEOUT/EILSEQ
	    // storm, recovering as needed.
	    case -EPIPE:
		defer_kevent (dev, EVENT_RX_HALT);
		// FALLTHROUGH

	    // software-driven interface shutdown
	    case -ECONNRESET:		// according to API spec
	    case -ECONNABORTED:		// some (now fixed?) UHCI bugs
		dbg ("%s rx shutdown, code %d", dev->net.name, urb_status);
		entry->state = rx_cleanup;
		// do urb frees only in the tasklet (UHCI has oopsed ...)
		entry->urb = urb;
		urb = 0;
		break;

	    // data overrun ... flush fifo?
	    case -EOVERFLOW:
		dev->stats.rx_over_errors++;
		// FALLTHROUGH
	    
	    default:
		// on unplug we get ETIMEDOUT (ohci) or EILSEQ (uhci)
		// until khubd sees its interrupt and disconnects us.
		// that can easily be hundreds of passes through here.
		entry->state = rx_cleanup;
		dev->stats.rx_errors++;
		dbg ("%s rx: status %d", dev->net.name, urb_status);
		break;
	}

	defer_bh (dev, skb);

	if (urb) {
		if (netif_running (&dev->net)
				&& !test_bit (EVENT_RX_HALT, &dev->flags)) {
			rx_submit (dev, urb, GFP_ATOMIC);
			return;
		}
		usb_free_urb (urb);
	}
#ifdef	VERBOSE
	dbg ("no read resubmitted");
#endif /* VERBOSE */
}

/*-------------------------------------------------------------------------*/

// unlink pending rx/tx; completion handlers do all other cleanup

static int unlink_urbs (struct sk_buff_head *q)
{
	unsigned long		flags;
	struct sk_buff		*skb, *skbnext;
	int			count = 0;

	spin_lock_irqsave (&q->lock, flags);
	for (skb = q->next; skb != (struct sk_buff *) q; skb = skbnext) {
		struct skb_data		*entry;
		struct urb		*urb;
		int			retval;

		entry = (struct skb_data *) skb->cb;
		urb = entry->urb;
		skbnext = skb->next;

		// during some PM-driven resume scenarios,
		// these (async) unlinks complete immediately
		retval = usb_unlink_urb (urb);
		if (retval != -EINPROGRESS && retval != 0)
			dbg ("unlink urb err, %d", retval);
		else
			count++;
	}
	spin_unlock_irqrestore (&q->lock, flags);
	return count;
}


/*-------------------------------------------------------------------------*/

// precondition: never called in_interrupt

static int usbnet_stop (struct net_device *net)
{
	struct usbnet		*dev = (struct usbnet *) net->priv;
	int			temp;
	DECLARE_WAIT_QUEUE_HEAD (unlink_wakeup); 
	DECLARE_WAITQUEUE (wait, current);

	mutex_lock (&dev->mutex);
	netif_stop_queue (net);

	if (dev->msg_level >= 2)
		devinfo (dev, "stop stats: rx/tx %ld/%ld, errs %ld/%ld",
			dev->stats.rx_packets, dev->stats.tx_packets, 
			dev->stats.rx_errors, dev->stats.tx_errors
			);

	// ensure there are no more active urbs
	add_wait_queue (&unlink_wakeup, &wait);
	dev->wait = &unlink_wakeup;
	temp = unlink_urbs (&dev->txq) + unlink_urbs (&dev->rxq);

	// maybe wait for deletions to finish.
	while (skb_queue_len (&dev->rxq)
			&& skb_queue_len (&dev->txq)
			&& skb_queue_len (&dev->done)) {
		set_current_state (TASK_UNINTERRUPTIBLE);
		schedule_timeout (UNLINK_TIMEOUT_JIFFIES);
		dbg ("waited for %d urb completions", temp);
	}
	dev->wait = 0;
	remove_wait_queue (&unlink_wakeup, &wait); 

	mutex_unlock (&dev->mutex);
	return 0;
}

/*-------------------------------------------------------------------------*/

// posts reads, and enables write queing

// precondition: never called in_interrupt

static int usbnet_open (struct net_device *net)
{
	struct usbnet		*dev = (struct usbnet *) net->priv;
	int			retval = 0;
	struct driver_info	*info = dev->driver_info;

	mutex_lock (&dev->mutex);

	// put into "known safe" state
	if (info->reset && (retval = info->reset (dev)) < 0) {
		devinfo (dev, "open reset fail (%d) usbnet usb-%s-%s, %s",
			retval,
			dev->udev->bus->bus_name, dev->udev->devpath,
			info->description);
		goto done;
	}

	// insist peer be connected
	if (info->check_connect && (retval = info->check_connect (dev)) < 0) {
		devdbg (dev, "can't open; %d", retval);
		goto done;
	}

	netif_start_queue (net);
	if (dev->msg_level >= 2)
		devinfo (dev, "open: enable queueing "
				"(rx %d, tx %d) mtu %d %s framing",
			RX_QLEN, TX_QLEN, dev->net.mtu,
			(info->flags & (FLAG_FRAMING_NC | FLAG_FRAMING_GL))
			    ? ((info->flags & FLAG_FRAMING_NC)
				? "NetChip"
				: "GeneSys")
			    : "raw"
			);

	// delay posting reads until we're fully open
	tasklet_schedule (&dev->bh);
done:
	mutex_unlock (&dev->mutex);
	return retval;
}

/*-------------------------------------------------------------------------*/

static void usbnet_get_drvinfo (struct net_device *net, struct ethtool_drvinfo *info)
{
	struct usbnet *dev = net->priv;

	strncpy (info->driver, driver_name, sizeof info->driver);
	strncpy (info->version, DRIVER_VERSION, sizeof info->version);
	strncpy (info->fw_version, dev->driver_info->description,
		sizeof info->fw_version);
	usb_make_path (dev->udev, info->bus_info, sizeof info->bus_info);
}

static u32 usbnet_get_link (struct net_device *net)
{
	struct usbnet *dev = net->priv;

	/* If a check_connect is defined, return it's results */
	if (dev->driver_info->check_connect)
		return dev->driver_info->check_connect (dev) == 0;

	/* Otherwise, we're up to avoid breaking scripts */
	return 1;
}

static u32 usbnet_get_msglevel (struct net_device *net)
{
	struct usbnet *dev = net->priv;

	return dev->msg_level;
}

static void usbnet_set_msglevel (struct net_device *net, u32 level)
{
	struct usbnet *dev = net->priv;

	dev->msg_level = level;
}

static int usbnet_ioctl (struct net_device *net, struct ifreq *rq, int cmd)
{
#ifdef NEED_MII
	{
	struct usbnet *dev = (struct usbnet *)net->priv;

	if (dev->mii.mdio_read != NULL && dev->mii.mdio_write != NULL)
		return generic_mii_ioctl(&dev->mii,
				(struct mii_ioctl_data *) &rq->ifr_data,
				cmd, NULL);
	}
#endif
	return -EOPNOTSUPP;
}

/*-------------------------------------------------------------------------*/

/* work that cannot be done in interrupt context uses keventd.
 *
 * NOTE:  "uhci" and "usb-uhci" may have trouble with this since they don't
 * queue control transfers to individual devices, and other threads could
 * trigger control requests concurrently.  hope that's rare.
 */
static void
kevent (void *data)
{
	struct usbnet		*dev = data;
	int			status;

	/* usb_clear_halt() needs a thread context */
	if (test_bit (EVENT_TX_HALT, &dev->flags)) {
		unlink_urbs (&dev->txq);
		status = usb_clear_halt (dev->udev, dev->out);
		if (status < 0)
			err ("%s: can't clear tx halt, status %d",
				dev->net.name, status);
		else {
			clear_bit (EVENT_TX_HALT, &dev->flags);
			netif_wake_queue (&dev->net);
		}
	}
	if (test_bit (EVENT_RX_HALT, &dev->flags)) {
		unlink_urbs (&dev->rxq);
		status = usb_clear_halt (dev->udev, dev->in);
		if (status < 0)
			err ("%s: can't clear rx halt, status %d",
				dev->net.name, status);
		else {
			clear_bit (EVENT_RX_HALT, &dev->flags);
			tasklet_schedule (&dev->bh);
		}
	}

	/* tasklet could resubmit itself forever if memory is tight */
	if (test_bit (EVENT_RX_MEMORY, &dev->flags)) {
		struct urb	*urb = 0;

		if (netif_running (&dev->net))
			urb = ALLOC_URB (0, GFP_KERNEL);
		else
			clear_bit (EVENT_RX_MEMORY, &dev->flags);
		if (urb != 0) {
			clear_bit (EVENT_RX_MEMORY, &dev->flags);
			rx_submit (dev, urb, GFP_KERNEL);
			tasklet_schedule (&dev->bh);
		}
	}

	if (dev->flags)
		dbg ("%s: kevent done, flags = 0x%lx",
			dev->net.name, dev->flags);
}

/*-------------------------------------------------------------------------*/

static void tx_complete (struct urb *urb)
{
	struct sk_buff		*skb = (struct sk_buff *) urb->context;
	struct skb_data		*entry = (struct skb_data *) skb->cb;
	struct usbnet		*dev = entry->dev;

	if (urb->status == -EPIPE)
		defer_kevent (dev, EVENT_TX_HALT);
	urb->dev = 0;
	entry->state = tx_done;
	defer_bh (dev, skb);
}

/*-------------------------------------------------------------------------*/

static void usbnet_tx_timeout (struct net_device *net)
{
	struct usbnet		*dev = (struct usbnet *) net->priv;

	unlink_urbs (&dev->txq);
	tasklet_schedule (&dev->bh);

	// FIXME: device recovery -- reset?
}

/*-------------------------------------------------------------------------*/

static int usbnet_start_xmit (struct sk_buff *skb, struct net_device *net)
{
	struct usbnet		*dev = (struct usbnet *) net->priv;
	int			length;
	int			retval = NET_XMIT_SUCCESS;
	struct urb		*urb = 0;
	struct skb_data		*entry;
	struct driver_info	*info = dev->driver_info;
	unsigned long		flags;
#ifdef	CONFIG_USB_NET1080
	struct nc_header	*header = 0;
	struct nc_trailer	*trailer = 0;
#endif	/* CONFIG_USB_NET1080 */

	// some devices want funky USB-level framing, for
	// win32 driver (usually) and/or hardware quirks
	if (info->tx_fixup) {
		skb = info->tx_fixup (dev, skb, GFP_ATOMIC);
		if (!skb) {
			dbg ("can't tx_fixup skb");
			goto drop;
		}
	}
	length = skb->len;

	if (!(urb = ALLOC_URB (0, GFP_ATOMIC))) {
		dbg ("no urb");
		goto drop;
	}

	entry = (struct skb_data *) skb->cb;
	entry->urb = urb;
	entry->dev = dev;
	entry->state = tx_start;
	entry->length = length;

	// FIXME: reorganize a bit, so that fixup() fills out NetChip
	// framing too. (Packet ID update needs the spinlock...)
	// [ BETTER:  we already own net->xmit_lock, that's enough ]

#ifdef	CONFIG_USB_NET1080
	if (info->flags & FLAG_FRAMING_NC) {
		header = (struct nc_header *) skb_push (skb, sizeof *header);
		header->hdr_len = cpu_to_le16 (sizeof (*header));
		header->packet_len = cpu_to_le16 (length);
		if (!((skb->len + sizeof *trailer) & 0x01))
			*skb_put (skb, 1) = PAD_BYTE;
		trailer = (struct nc_trailer *) skb_put (skb, sizeof *trailer);
	} else
#endif	/* CONFIG_USB_NET1080 */

	/* don't assume the hardware handles USB_ZERO_PACKET */
	if ((length % dev->maxpacket) == 0)
		skb->len++;

	usb_fill_bulk_urb (urb, dev->udev, dev->out,
			skb->data, skb->len, tx_complete, skb);
	urb->transfer_flags |= USB_ASYNC_UNLINK;

	spin_lock_irqsave (&dev->txq.lock, flags);

#ifdef	CONFIG_USB_NET1080
	if (info->flags & FLAG_FRAMING_NC) {
		header->packet_id = cpu_to_le16 (dev->packet_id++);
		put_unaligned (header->packet_id, &trailer->packet_id);
#if 0
		devdbg (dev, "frame >tx h %d p %d id %d",
			header->hdr_len, header->packet_len,
			header->packet_id);
#endif
	}
#endif	/* CONFIG_USB_NET1080 */

	switch ((retval = SUBMIT_URB (urb, GFP_ATOMIC))) {
	case -EPIPE:
		netif_stop_queue (net);
		defer_kevent (dev, EVENT_TX_HALT);
		break;
	default:
		dbg ("%s tx: submit urb err %d", net->name, retval);
		break;
	case 0:
		net->trans_start = jiffies;
		__skb_queue_tail (&dev->txq, skb);
		if (dev->txq.qlen >= TX_QLEN)
			netif_stop_queue (net);
	}
	spin_unlock_irqrestore (&dev->txq.lock, flags);

	if (retval) {
		devdbg (dev, "drop, code %d", retval);
drop:
		retval = NET_XMIT_SUCCESS;
		dev->stats.tx_dropped++;
		if (skb)
			dev_kfree_skb_any (skb);
		usb_free_urb (urb);
#ifdef	VERBOSE
	} else {
		devdbg (dev, "> tx, len %d, type 0x%x",
			length, skb->protocol);
#endif
	}
	return retval;
}


/*-------------------------------------------------------------------------*/

// tasklet ... work that avoided running in_irq()

static void usbnet_bh (unsigned long param)
{
	struct usbnet		*dev = (struct usbnet *) param;
	struct sk_buff		*skb;
	struct skb_data		*entry;

	while ((skb = skb_dequeue (&dev->done))) {
		entry = (struct skb_data *) skb->cb;
		switch (entry->state) {
		    case rx_done:
			entry->state = rx_cleanup;
			rx_process (dev, skb);
			continue;
		    case tx_done:
			if (entry->urb->status) {
				// can this statistic become more specific?
				dev->stats.tx_errors++;
				dbg ("%s tx: err %d", dev->net.name,
					entry->urb->status);
			} else {
				dev->stats.tx_packets++;
				dev->stats.tx_bytes += entry->length;
			}
			// FALLTHROUGH:
		    case rx_cleanup:
			usb_free_urb (entry->urb);
			dev_kfree_skb (skb);
			continue;
		    default:
			dbg ("%s: bogus skb state %d",
				dev->net.name, entry->state);
		}
	}

	// waiting for all pending urbs to complete?
	if (dev->wait) {
		if ((dev->txq.qlen + dev->rxq.qlen + dev->done.qlen) == 0) {
			wake_up (dev->wait);
		}

	// or are we maybe short a few urbs?
	} else if (netif_running (&dev->net)
			&& !test_bit (EVENT_RX_HALT, &dev->flags)) {
		int	temp = dev->rxq.qlen;

		if (temp < RX_QLEN) {
			struct urb	*urb;
			int		i;
			for (i = 0; i < 3 && dev->rxq.qlen < RX_QLEN; i++) {
				if ((urb = ALLOC_URB (0, GFP_ATOMIC)) != 0)
					rx_submit (dev, urb, GFP_ATOMIC);
			}
			if (temp != dev->rxq.qlen)
				devdbg (dev, "rxqlen %d --> %d",
						temp, dev->rxq.qlen);
			if (dev->rxq.qlen < RX_QLEN)
				tasklet_schedule (&dev->bh);
		}
		if (dev->txq.qlen < TX_QLEN)
			netif_wake_queue (&dev->net);
	}
}



/*-------------------------------------------------------------------------
 *
 * USB Device Driver support
 *
 *-------------------------------------------------------------------------*/
 
// precondition: never called in_interrupt

static void usbnet_disconnect (struct usb_device *udev, void *ptr)
{
	struct usbnet	*dev = (struct usbnet *) ptr;

	devinfo (dev, "unregister usbnet usb-%s-%s, %s",
		udev->bus->bus_name, udev->devpath,
		dev->driver_info->description);
	
	unregister_netdev (&dev->net);

	mutex_lock (&usbnet_mutex);
	mutex_lock (&dev->mutex);
	list_del (&dev->dev_list);
	mutex_unlock (&usbnet_mutex);

	// assuming we used keventd, it must quiesce too
	flush_scheduled_tasks ();

	kfree (dev);
	usb_put_dev (udev);
}


/*-------------------------------------------------------------------------*/

// precondition: never called in_interrupt

static void *
usbnet_probe (struct usb_device *udev, unsigned ifnum,
			const struct usb_device_id *prod)
{
	struct usbnet			*dev;
	struct net_device 		*net;
	struct driver_info		*info;
	int				altnum = 0;
	int				status;

	info = (struct driver_info *) prod->driver_info;

#ifdef CONFIG_USB_ZAURUS
	if (info == &zaurus_sl5x00_info) {
		int	status;

		/* old ROMs have more than one config
		 * so we have to make sure config="1" (?)
		 */
		status = usb_set_configuration (udev, 1);
		if (status < 0) {
			err ("set_config failed, %d", status);
			return 0;
		}
		altnum = 1;
	}
#endif

	// more sanity (unless the device is broken)
	if (!(info->flags & FLAG_NO_SETINT)) {
		if (usb_set_interface (udev, ifnum, altnum) < 0) {
			err ("set_interface failed");
			return 0;
		}
	}

	// set up our own records
	if (!(dev = kmalloc (sizeof *dev, GFP_KERNEL))) {
		dbg ("can't kmalloc dev");
		return 0;
	}
	memset (dev, 0, sizeof *dev);

	init_MUTEX_LOCKED (&dev->mutex);
	init_MUTEX (&dev->phy_mutex);
	dev->ifnum=ifnum;
	usb_get_dev (udev);
	dev->udev = udev;
	dev->driver_info = info;
	dev->msg_level = msg_level;
	INIT_LIST_HEAD (&dev->dev_list);
	skb_queue_head_init (&dev->rxq);
	skb_queue_head_init (&dev->txq);
	skb_queue_head_init (&dev->done);
	dev->bh.func = usbnet_bh;
	dev->bh.data = (unsigned long) dev;
	INIT_TQUEUE (&dev->kevent, kevent, dev);

	// set up network interface records
	net = &dev->net;
	SET_MODULE_OWNER (net);
	net->priv = dev;
	strcpy (net->name, "usb%d");
	memcpy (net->dev_addr, node_id, sizeof node_id);

	// point-to-point link ... we always use Ethernet headers 
	// supports win32 interop and the bridge driver.
	ether_setup (net);

	net->change_mtu = usbnet_change_mtu;
	net->get_stats = usbnet_get_stats;
	net->hard_start_xmit = usbnet_start_xmit;
	net->open = usbnet_open;
	net->stop = usbnet_stop;
	net->watchdog_timeo = TX_TIMEOUT_JIFFIES;
	net->tx_timeout = usbnet_tx_timeout;
	net->do_ioctl = usbnet_ioctl;
	net->ethtool_ops = &usbnet_ethtool_ops;

	// allow device-specific bind/init procedures
	// NOTE net->name still not usable ...
	if (info->bind) {
		status = info->bind (dev, udev);
		// heuristic:  "usb%d" for links we know are two-host,
		// else "eth%d" when there's reasonable doubt.  userspace
		// can rename the link if it knows better.
		if ((dev->driver_info->flags & FLAG_ETHER) != 0
				&& (net->dev_addr [0] & 0x02) == 0)
			strcpy (net->name, "eth%d");
	} else if (!info->in || info->out)
		status = get_endpoints (dev, udev->actconfig->interface + ifnum);
	else {
		dev->in = usb_rcvbulkpipe (udev, info->in);
		dev->out = usb_sndbulkpipe (udev, info->out);
	}

	dev->maxpacket = usb_maxpacket (dev->udev, dev->out, 1);

	register_netdev (&dev->net);
	devinfo (dev, "register usbnet usb-%s-%s, %s",
		udev->bus->bus_name, udev->devpath,
		dev->driver_info->description);

	// ok, it's ready to go.
	mutex_lock (&usbnet_mutex);
	list_add (&dev->dev_list, &usbnet_list);
	mutex_unlock (&dev->mutex);

	// start as if the link is up
	netif_device_attach (&dev->net);

	mutex_unlock (&usbnet_mutex);
	return dev;
}


/*-------------------------------------------------------------------------*/

/*
 * chip vendor names won't normally be on the cables, and
 * may not be on the device.
 */

static const struct usb_device_id	products [] = {

#ifdef	CONFIG_USB_MCS7830
{
	USB_DEVICE (0x9710, 0x7830), 
	.driver_info =	(unsigned long) &moschip_info,
},
#endif

#ifdef	CONFIG_USB_AN2720
{
	USB_DEVICE (0x0547, 0x2720),	// AnchorChips defaults
	.driver_info =	(unsigned long) &an2720_info,
}, {
	USB_DEVICE (0x0547, 0x2727),	// Xircom PGUNET
	.driver_info =	(unsigned long) &an2720_info,
},
#endif

#ifdef CONFIG_USB_AX8817X
{
	// Linksys USB200M
	USB_DEVICE (0x077b, 0x2226),
	.driver_info =	(unsigned long) &ax8817x_info,
}, {
	// Netgear FA120
	USB_DEVICE (0x0846, 0x1040),
	.driver_info =	(unsigned long) &netgear_fa120_info,
}, {
	// DLink DUB-E100
	USB_DEVICE (0x2001, 0x1a00),
	.driver_info =	(unsigned long) &dlink_dub_e100_info,
}, {
	// Intellinet, ST Lab USB Ethernet
	USB_DEVICE (0x0b95, 0x1720),
	.driver_info =	(unsigned long) &ax8817x_info,
}, {
	// Hawking UF200, TrendNet TU2-ET100
	USB_DEVICE (0x07b8, 0x420a),
	.driver_info =	(unsigned long) &hawking_uf200_info,
}, {
	// ATEN UC210T
	USB_DEVICE (0x0557, 0x2009),
	.driver_info =  (unsigned long) &ax8817x_info,
},
#endif

#ifdef	CONFIG_USB_BELKIN
{
	USB_DEVICE (0x050d, 0x0004),	// Belkin
	.driver_info =	(unsigned long) &belkin_info,
}, {
	USB_DEVICE (0x056c, 0x8100),	// eTEK
	.driver_info =	(unsigned long) &belkin_info,
}, {
	USB_DEVICE (0x0525, 0x9901),	// Advance USBNET (eTEK)
	.driver_info =	(unsigned long) &belkin_info,
},
#endif

#ifdef	CONFIG_USB_EPSON2888
{
	USB_DEVICE (0x0525, 0x2888),	// EPSON USB client
	.driver_info	= (unsigned long) &epson2888_info,
},
#endif

#ifdef	CONFIG_USB_GENESYS
{
	USB_DEVICE (0x05e3, 0x0502),	// GL620USB-A
	.driver_info =	(unsigned long) &genelink_info,
},
	/* NOT: USB_DEVICE (0x05e3, 0x0501),	// GL620USB
	 * that's half duplex, not currently supported
	 */
#endif

#ifdef	CONFIG_USB_NET1080
{
	USB_DEVICE (0x0525, 0x1080),	// NetChip ref design
	.driver_info =	(unsigned long) &net1080_info,
}, {
	USB_DEVICE (0x06D0, 0x0622),	// Laplink Gold
	.driver_info =	(unsigned long) &net1080_info,
},
#endif

#ifdef CONFIG_USB_PL2301
{
	USB_DEVICE (0x067b, 0x0000),	// PL-2301
	.driver_info =	(unsigned long) &prolific_info,
}, {
	USB_DEVICE (0x067b, 0x0001),	// PL-2302
	.driver_info =	(unsigned long) &prolific_info,
},
#endif

#ifdef	CONFIG_USB_ARMLINUX
/*
 * SA-1100 using standard ARM Linux kernels, or compatible.
 * Often used when talking to Linux PDAs (iPaq, Yopy, etc).
 * The sa-1100 "usb-eth" driver handles the basic framing.
 * ARMv4.
 *
 * PXA2xx using usb "gadget" driver, or older "usb-eth" much like
 * the sa1100 one. (But PXA hardware uses different endpoints.)
 * ARMv5TE.
 */
{
	// 1183 = 0x049F, both used as hex values?
	// Compaq "Itsy" vendor/product id
	// version numbers vary, along with endpoint usage
	// but otherwise they're protocol-compatible
	USB_DEVICE (0x049F, 0x505A),
	.driver_info =	(unsigned long) &linuxdev_info,
}, {
	USB_DEVICE (0x0E7E, 0x1001),	// G.Mate "Yopy"
	.driver_info =	(unsigned long) &yopy_info,
}, {
	USB_DEVICE (0x8086, 0x07d3),	// "blob" bootloader
	.driver_info =	(unsigned long) &blob_info,
}, 
#endif

#ifdef	CONFIG_USB_ZAURUS
/*
 * SA-1100 based Sharp Zaurus ("collie"), or compatible.
 * Same idea as above, but different framing.
 */
{
	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
			  | USB_DEVICE_ID_MATCH_DEVICE, 
	.idVendor		= 0x04DD,
	.idProduct		= 0x8004,
	.bInterfaceClass	= 0x0a,
	.bInterfaceSubClass	= 0x00,
	.bInterfaceProtocol	= 0x00,
	.driver_info =  (unsigned long) &zaurus_sl5x00_info,
}, {
	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
			  | USB_DEVICE_ID_MATCH_DEVICE, 
	.idVendor		= 0x04DD,
	.idProduct		= 0x8005, /* A-300 */
	.bInterfaceClass	= 0x02,
	.bInterfaceSubClass	= 0x0a,
	.bInterfaceProtocol	= 0x00,
	.driver_info =  (unsigned long) &zaurus_pxa_info,
}, {
	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
			  | USB_DEVICE_ID_MATCH_DEVICE, 
	.idVendor		= 0x04DD,
	.idProduct		= 0x8006, /* B-500/SL-5600 */
	.bInterfaceClass	= 0x02,
	.bInterfaceSubClass	= 0x0a,
	.bInterfaceProtocol	= 0x00,
	.driver_info =  (unsigned long) &zaurus_pxa_info,
}, {
	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
			  | USB_DEVICE_ID_MATCH_DEVICE, 
	.idVendor		= 0x04DD,
	.idProduct		= 0x8007, /* C-700 */
	.bInterfaceClass	= 0x02,
	.bInterfaceSubClass	= 0x0a,
	.bInterfaceProtocol	= 0x00,
	.driver_info =  (unsigned long) &zaurus_pxa_info,
}, {
	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
			  | USB_DEVICE_ID_MATCH_DEVICE,
	.idVendor		= 0x04DD,
	.idProduct		= 0x9031, /* C-750 C-760 */
	.bInterfaceClass	= 0x02,
	.bInterfaceSubClass	= 0x0a,
	.bInterfaceProtocol	= 0x00,
	.driver_info =	(unsigned long) &zaurus_pxa_info,
}, {
	.match_flags	=   USB_DEVICE_ID_MATCH_INT_INFO
			  | USB_DEVICE_ID_MATCH_DEVICE,
	.idVendor		= 0x04DD,
	.idProduct		= 0x9032, /* SL-6000 */
	.bInterfaceClass	= 0x02,
	.bInterfaceSubClass	= 0x0a,
	.bInterfaceProtocol	= 0x00,
	.driver_info =	(unsigned long) &zaurus_pxa_info,
},
#endif

	{ },		// END
};
MODULE_DEVICE_TABLE (usb, products);

static struct usb_driver usbnet_driver = {
	.name =		driver_name,
	.id_table =	products,
	.probe =	usbnet_probe,
	.disconnect =	usbnet_disconnect,
};

/* Default ethtool_ops assigned.  Devices can override in their bind() routine */
static struct ethtool_ops usbnet_ethtool_ops = {
	.get_drvinfo		= usbnet_get_drvinfo,
	.get_link		= usbnet_get_link,
	.get_msglevel		= usbnet_get_msglevel,
	.set_msglevel		= usbnet_set_msglevel,
};
/*-------------------------------------------------------------------------*/

static int __init usbnet_init (void)
{
	// compiler should optimize this out
	if (sizeof (((struct sk_buff *)0)->cb) < sizeof (struct skb_data))
		BUG ();

	get_random_bytes (node_id, sizeof node_id);
	node_id [0] &= 0xfe;	// clear multicast bit
	node_id [0] |= 0x02;    // set local assignment bit (IEEE802)

 	if (usb_register (&usbnet_driver) < 0)
 		return -1;

	return 0;
}
module_init (usbnet_init);

static void __exit usbnet_exit (void)
{
 	usb_deregister (&usbnet_driver);
}
module_exit (usbnet_exit);

EXPORT_NO_SYMBOLS;
MODULE_AUTHOR ("David Brownell <[email protected]>");
MODULE_DESCRIPTION ("USB Host-to-Host Link Drivers (numerous vendors)");
MODULE_LICENSE ("GPL");

/*
 * MosChips MCS7830 based USB 2.0 Ethernet Devices
 *
 * based on usbnet.c, asix.c and the vendor provided mcs7830 driver
 *
 * Copyright (C) 2006 Arnd Bergmann <[email protected]>
 * Copyright (C) 2003-2005 David Hollis <[email protected]>
 * Copyright (C) 2005 Phil Chang <[email protected]>
 * Copyright (c) 2002-2003 TiVo Inc.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */

#include <linux/crc32.h>

/* functions defined in usbnet.c */
static void usbnet_get_drvinfo (struct net_device *, struct ethtool_drvinfo *);
static u32 usbnet_get_link (struct net_device *);
static u32 usbnet_get_msglevel (struct net_device *);
static void usbnet_set_msglevel (struct net_device *, u32);
static int get_endpoints (struct usbnet *, struct usb_interface *);

#define ADVERTISE_PAUSE_CAP		0x0400

/* requests */
#define MCS7830_RD_BMREQ	(USB_DIR_IN  | USB_TYPE_VENDOR | \
				 USB_RECIP_DEVICE)
#define MCS7830_WR_BMREQ	(USB_DIR_OUT | USB_TYPE_VENDOR | \
				 USB_RECIP_DEVICE)
#define MCS7830_RD_BREQ		0x0E
#define MCS7830_WR_BREQ		0x0D

#define MCS7830_CTRL_TIMEOUT	1000
#define MCS7830_MAX_MCAST	64

#define MCS7830_VENDOR_ID	0x9710
#define MCS7830_PRODUCT_ID	0x7830

#define MCS7830_MII_ADVERTISE	(ADVERTISE_PAUSE_CAP | ADVERTISE_100FULL | \
				 ADVERTISE_100HALF | ADVERTISE_10FULL | \
				 ADVERTISE_10HALF | ADVERTISE_CSMA)

/* HIF_REG_XX coressponding index value */
enum {
	HIF_REG_MULTICAST_HASH			= 0x00,
	HIF_REG_PACKET_GAP1			= 0x08,
	HIF_REG_PACKET_GAP2			= 0x09,
	HIF_REG_PHY_DATA			= 0x0a,
	HIF_REG_PHY_CMD1			= 0x0c,
	   HIF_REG_PHY_CMD1_READ		= 0x40,
	   HIF_REG_PHY_CMD1_WRITE		= 0x20,
	   HIF_REG_PHY_CMD1_PHYADDR		= 0x01,
	HIF_REG_PHY_CMD2			= 0x0d,
	   HIF_REG_PHY_CMD2_PEND_FLAG_BIT	= 0x80,
	   HIF_REG_PHY_CMD2_READY_FLAG_BIT	= 0x40,
	HIF_REG_CONFIG				= 0x0e,
	   HIF_REG_CONFIG_CFG			= 0x80,
	   HIF_REG_CONFIG_SPEED100		= 0x40,
	   HIF_REG_CONFIG_FULLDUPLEX_ENABLE	= 0x20,
	   HIF_REG_CONFIG_RXENABLE		= 0x10,
	   HIF_REG_CONFIG_TXENABLE		= 0x08,
	   HIF_REG_CONFIG_SLEEPMODE		= 0x04,
	   HIF_REG_CONFIG_ALLMULTICAST		= 0x02,
	   HIF_REG_CONFIG_PROMISCIOUS		= 0x01,
	HIF_REG_ETHERNET_ADDR			= 0x0f,
	HIF_REG_22				= 0x15,
	HIF_REG_PAUSE_THRESHOLD			= 0x16,
	   HIF_REG_PAUSE_THRESHOLD_DEFAULT	= 0,
};

struct mcs7830_data {
	u8 multi_filter[8];
	u8 config;
};

static int mcs7830_get_reg(struct usbnet *dev, u16 index, u16 size, void *data)
{
	struct usb_device *xdev = dev->udev;
	int ret;

	ret = usb_control_msg(xdev, usb_rcvctrlpipe(xdev, 0), MCS7830_RD_BREQ,
			      MCS7830_RD_BMREQ, 0x0000, index, data,
			      size, msecs_to_jiffies(MCS7830_CTRL_TIMEOUT));
	return ret;
}

static int mcs7830_set_reg(struct usbnet *dev, u16 index, u16 size, void *data)
{
	struct usb_device *xdev = dev->udev;
	int ret;

	ret = usb_control_msg(xdev, usb_sndctrlpipe(xdev, 0), MCS7830_WR_BREQ,
			      MCS7830_WR_BMREQ, 0x0000, index, data,
			      size, msecs_to_jiffies(MCS7830_CTRL_TIMEOUT));
	return ret;
}

static void mcs7830_async_cmd_callback(struct urb *urb)
{
	struct usb_ctrlrequest *req = (struct usb_ctrlrequest *)urb->context;

	if (urb->status < 0)
		printk(KERN_DEBUG "mcs7830_async_cmd_callback() failed with %d",
			urb->status);

	kfree(req);
	usb_free_urb(urb);
}

static void mcs7830_set_reg_async(struct usbnet *dev, u16 index, u16 size, void *data)
{
	struct usb_ctrlrequest *req;
	int ret;
	struct urb *urb;

	urb = ALLOC_URB(0, GFP_ATOMIC);
	if (!urb) {
		printk(KERN_DEBUG "Error allocating URB "
				"in write_cmd_async!");
		return;
	}

	req = kmalloc(sizeof *req, GFP_ATOMIC);
	if (!req) {
		printk(KERN_ERR "Failed to allocate memory for "
				"control request");
		goto out;
	}
	req->bRequestType = MCS7830_WR_BMREQ;
	req->bRequest = MCS7830_WR_BREQ;
	req->wValue = 0;
	req->wIndex = cpu_to_le16(index);
	req->wLength = cpu_to_le16(size);

	usb_fill_control_urb(urb, dev->udev,
			     usb_sndctrlpipe(dev->udev, 0),
			     (void *)req, data, size,
			     mcs7830_async_cmd_callback, req);

	ret = SUBMIT_URB(urb, GFP_ATOMIC);
	if (ret < 0) {
		printk(KERN_ERR "Error submitting the control "
				"message: ret=%d", ret);
		goto out;
	}
	return;
out:
	kfree(req);
	usb_free_urb(urb);
}

static int mcs7830_get_address(struct usbnet *dev)
{
	int ret;
	ret = mcs7830_get_reg(dev, HIF_REG_ETHERNET_ADDR, ETH_ALEN,
				   dev->net.dev_addr);
	if (ret < 0)
		return ret;
	return 0;
}

static int mcs7830_read_phy(struct usbnet *dev, u8 index)
{
	int ret;
	int i;
	// __le16 val;
	__u16 val;

	u8 cmd[2] = {
		HIF_REG_PHY_CMD1_READ | HIF_REG_PHY_CMD1_PHYADDR,
		HIF_REG_PHY_CMD2_PEND_FLAG_BIT | index,
	};

	mutex_lock(&dev->phy_mutex);
	/* write the MII command */
	ret = mcs7830_set_reg(dev, HIF_REG_PHY_CMD1, 2, cmd);
	if (ret < 0)
		goto out;

	/* wait for the data to become valid, should be within < 1ms */
	for (i = 0; i < 10; i++) {
		ret = mcs7830_get_reg(dev, HIF_REG_PHY_CMD1, 2, cmd);
		if ((ret < 0) || (cmd[1] & HIF_REG_PHY_CMD2_READY_FLAG_BIT))
			break;
		ret = -EIO;
		msleep(1);
	}
	if (ret < 0)
		goto out;

	/* read actual register contents */
	ret = mcs7830_get_reg(dev, HIF_REG_PHY_DATA, 2, &val);
	if (ret < 0)
		goto out;
	ret = le16_to_cpu(val);
	printk(KERN_DEBUG "read PHY reg %02x: %04x (%d tries)\n",
		index, val, i);
out:
	mutex_unlock(&dev->phy_mutex);
	return ret;
}

static int mcs7830_write_phy(struct usbnet *dev, u8 index, u16 val)
{
	int ret;
	int i;
	// __le16 le_val;
	__u16 le_val;

	u8 cmd[2] = {
		HIF_REG_PHY_CMD1_WRITE | HIF_REG_PHY_CMD1_PHYADDR,
		HIF_REG_PHY_CMD2_PEND_FLAG_BIT | (index & 0x1F),
	};

	mutex_lock(&dev->phy_mutex);

	/* write the new register contents */
	le_val = cpu_to_le16(val);
	ret = mcs7830_set_reg(dev, HIF_REG_PHY_DATA, 2, &le_val);
	if (ret < 0)
		goto out;

	/* write the MII command */
	ret = mcs7830_set_reg(dev, HIF_REG_PHY_CMD1, 2, cmd);
	if (ret < 0)
		goto out;

	/* wait for the command to be accepted by the PHY */
	for (i = 0; i < 10; i++) {
		ret = mcs7830_get_reg(dev, HIF_REG_PHY_CMD1, 2, cmd);
		if ((ret < 0) || (cmd[1] & HIF_REG_PHY_CMD2_READY_FLAG_BIT))
			break;
		ret = -EIO;
		msleep(1);
	}
	if (ret < 0)
		goto out;

	ret = 0;
	printk(KERN_DEBUG "write PHY reg %02x: %04x (%d tries)\n",
		index, val, i);
out:
	mutex_unlock(&dev->phy_mutex);
	return ret;
}

/*
 * This algorithm comes from the original mcs7830 version 1.4 driver,
 * not sure if it is needed.
 */
static int mcs7830_set_autoneg(struct usbnet *dev, int ptrUserPhyMode)
{
	int ret;
	/* Enable all media types */
	ret = mcs7830_write_phy(dev, MII_ADVERTISE, MCS7830_MII_ADVERTISE);

	/* First reset BMCR */
	if (!ret)
		ret = mcs7830_write_phy(dev, MII_BMCR, 0x0000);
	/* Enable Auto Neg */
	if (!ret)
		ret = mcs7830_write_phy(dev, MII_BMCR, BMCR_ANENABLE);
	/* Restart Auto Neg (Keep the Enable Auto Neg Bit Set) */
	if (!ret)
		ret = mcs7830_write_phy(dev, MII_BMCR,
				BMCR_ANENABLE | BMCR_ANRESTART	);
	return ret < 0 ? : 0;
}


/*
 * if we can read register 22, the chip revision is C or higher
 */
static int mcs7830_get_rev(struct usbnet *dev)
{
	u8 dummy[2];
	int ret;
	ret = mcs7830_get_reg(dev, HIF_REG_22, 2, dummy);
	if (ret > 0)
		return 2; /* Rev C or later */
	return 1; /* earlier revision */
}

/*
 * On rev. C we need to set the pause threshold
 */
static void mcs7830_rev_C_fixup(struct usbnet *dev)
{
	u8 pause_threshold = HIF_REG_PAUSE_THRESHOLD_DEFAULT;
	int retry;

	for (retry = 0; retry < 2; retry++) {
		if (mcs7830_get_rev(dev) == 2) {
			printk(KERN_INFO "applying rev.C fixup\n");
			mcs7830_set_reg(dev, HIF_REG_PAUSE_THRESHOLD,
					1, &pause_threshold);
		}
		msleep(1);
	}
}

static int mcs7830_init_dev(struct usbnet *dev)
{
	int ret;
	int retry;

	/* Read MAC address from EEPROM */
	ret = -EINVAL;
	for (retry = 0; retry < 5 && ret; retry++)
		ret = mcs7830_get_address(dev);
	if (ret) {
		printk(KERN_WARNING "Cannot read MAC address\n");
		goto out;
	}

	/* Set up PHY */
	ret = mcs7830_set_autoneg(dev, 0);
	if (ret) {
		printk(KERN_INFO "Cannot set autoneg\n");
		goto out;
	}

	mcs7830_rev_C_fixup(dev);
	ret = 0;
out:
	return ret;
}

static int mcs7830_mdio_read(struct net_device *netdev, int phy_id,
			     int location)
{
	struct usbnet *dev = netdev->priv;
	return mcs7830_read_phy(dev, location);
}

static void mcs7830_mdio_write(struct net_device *netdev, int phy_id,
				int location, int val)
{
	struct usbnet *dev = netdev->priv;
	mcs7830_write_phy(dev, location, val);
}

static int mcs7830_ioctl(struct net_device *net, struct ifreq *rq, int cmd)
{
	struct usbnet *dev = netdev_priv(net);
	return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL);
}

/* credits go to asix_set_multicast */
static void mcs7830_set_multicast(struct net_device *net)
{
	struct usbnet *dev = netdev_priv(net);
	struct mcs7830_data *data = (struct mcs7830_data *)&dev->driver_info->data;

	data->config = HIF_REG_CONFIG_TXENABLE;

	/* this should not be needed, but it doesn't work otherwise */
	data->config |= HIF_REG_CONFIG_ALLMULTICAST;

	if (net->flags & IFF_PROMISC) {
		data->config |= HIF_REG_CONFIG_PROMISCIOUS;
	} else if (net->flags & IFF_ALLMULTI
		   || net->mc_count > MCS7830_MAX_MCAST) {
		data->config |= HIF_REG_CONFIG_ALLMULTICAST;
	} else if (net->mc_count == 0) {
		/* just broadcast and directed */
	} else {
		/* We use the 20 byte dev->data
		 * for our 8 byte filter buffer
		 * to avoid allocating memory that
		 * is tricky to free later */
		struct dev_mc_list *mc_list = net->mc_list;
		u32 crc_bits;
		int i;

		memset(data->multi_filter, 0, sizeof data->multi_filter);

		/* Build the multicast hash filter. */
		for (i = 0; i < net->mc_count; i++) {
			crc_bits = ether_crc(ETH_ALEN, mc_list->dmi_addr) >> 26;
			data->multi_filter[crc_bits >> 3] |= 1 << (crc_bits & 7);
			mc_list = mc_list->next;
		}

		mcs7830_set_reg_async(dev, HIF_REG_MULTICAST_HASH,
				sizeof data->multi_filter,
				data->multi_filter);
	}

	mcs7830_set_reg_async(dev, HIF_REG_CONFIG, 1, &data->config);
}

static int mcs7830_get_regs_len(struct net_device *net)
{
	struct usbnet *dev = netdev_priv(net);

	switch (mcs7830_get_rev(dev)) {
	case 1:
		return 21;
	case 2:
		return 32;
	}
	return 0;
}

static void mcs7830_get_drvinfo(struct net_device *net, struct ethtool_drvinfo *drvinfo)
{
	usbnet_get_drvinfo(net, drvinfo);
	drvinfo->regdump_len = mcs7830_get_regs_len(net);
}

static void mcs7830_get_regs(struct net_device *net, struct ethtool_regs *regs, void *data)
{
	struct usbnet *dev = netdev_priv(net);

	regs->version = mcs7830_get_rev(dev);
	mcs7830_get_reg(dev, 0, regs->len, data);
}

// static int mcs7830_bind(struct usbnet *dev, struct usb_interface *udev)
static int mcs7830_bind(struct usbnet *dev, struct usb_device *udev)
{
	struct net_device *net = &(dev->net);
	int ret;

	ret = mcs7830_init_dev(dev);
	if (ret)
		goto out;

	net->do_ioctl = mcs7830_ioctl;

	net->ethtool_ops->get_drvinfo = mcs7830_get_drvinfo;
	net->ethtool_ops->get_regs_len = mcs7830_get_regs_len;
	net->ethtool_ops->get_regs = mcs7830_get_regs;

	net->set_multicast_list = mcs7830_set_multicast;
	mcs7830_set_multicast(net);

	/* reserve space for the status byte on rx */
	// dev->rx_urb_size = ETH_FRAME_LEN + 1;

	dev->mii.mdio_read = mcs7830_mdio_read;
	dev->mii.mdio_write = mcs7830_mdio_write;
	dev->mii.dev = net;
	dev->mii.phy_id_mask = 0x3f;
	dev->mii.reg_num_mask = 0x1f;
	dev->mii.phy_id = *((u8 *) net->dev_addr + 1);

	ret = get_endpoints(dev, udev->actconfig->interface+dev->ifnum);

out:
	return ret;
}

/* The chip always appends a status bytes that we need to strip */
static int mcs7830_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
{
	u8 status;

	if (skb->len == 0) {
		printk(KERN_ERR "unexpected empty rx frame\n");
		return 0;
	}

	skb_trim(skb, skb->len - 1);
	status = skb->data[skb->len];

	if (status != 0x20)
		printk(KERN_DEBUG "rx fixup status %x\n", status);

	return skb->len > 0;
}

static const struct driver_info moschip_info = {
	.description	= "MOSCHIP 7830 usb-NET adapter",
	.bind		= mcs7830_bind,
	.rx_fixup	= mcs7830_rx_fixup,
	.flags		= FLAG_ETHER | FLAG_RX_ONEMORE,
	.in		= 1,
	.out		= 2,
};