[PATCH] USB: m66592-udc: Add support for SH7722 USBF

Add support for SuperH SH7722 USB Function.

M66592 is similar to SH7722 USBF. It can support SH7722 USBF by
changing several M66592 code.

Signed-off-by: Yoshihiro Shimoda <[email protected]>
Acked-by: David Brownell <[email protected]>
---

 drivers/usb/gadget/Kconfig      |   10 +++++
 drivers/usb/gadget/m66592-udc.c |   55 +++++++++++++++++++++++++++++-
 drivers/usb/gadget/m66592-udc.h |   54 +++++++++++++++++++++++++++++
 3 files changed, 118 insertions(+), 1 deletion(-)

diff -uprN a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
--- a/drivers/usb/gadget/Kconfig	2007-10-24 12:50:57.000000000 +0900
+++ b/drivers/usb/gadget/Kconfig	2007-11-09 14:04:17.000000000 +0900
@@ -220,6 +220,16 @@ config USB_M66592
 	default USB_GADGET
 	select USB_GADGET_SELECTED

+config SUPERH_BUILT_IN_M66592
+	boolean "Enable SuperH built-in USB like the M66592"
+	depends on USB_GADGET_M66592 && CPU_SUBTYPE_SH7722
+	help
+	   SH7722 has USB like the M66592.
+
+	   The transfer rate is very slow when use "Ethernet Gadget".
+	   However, this problem is improved if change a value of
+	   NET_IP_ALIGN to 4.
+
 config USB_GADGET_GOKU
 	boolean "Toshiba TC86C001 'Goku-S'"
 	depends on PCI
diff -uprN a/drivers/usb/gadget/m66592-udc.c b/drivers/usb/gadget/m66592-udc.c
--- a/drivers/usb/gadget/m66592-udc.c	2007-10-24 12:50:57.000000000 +0900
+++ b/drivers/usb/gadget/m66592-udc.c	2007-11-09 15:53:18.000000000 +0900
@@ -36,9 +36,14 @@ MODULE_DESCRIPTION("M66592 USB gadget dr
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Yoshihiro Shimoda");

-#define DRIVER_VERSION	"29 May 2007"
+#define DRIVER_VERSION	"18 Oct 2007"

 /* module parameters */
+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+static unsigned short endian = M66592_LITTLE;
+module_param(endian, ushort, 0644);
+MODULE_PARM_DESC(endian, "data endian: big=0, little=0 (default=0)");
+#else
 static unsigned short clock = M66592_XTAL24;
 module_param(clock, ushort, 0644);
 MODULE_PARM_DESC(clock, "input clock: 48MHz=32768, 24MHz=16384, 12MHz=0 "
@@ -56,6 +61,7 @@ static unsigned short irq_sense = M66592
 module_param(irq_sense, ushort, 0644);
 MODULE_PARM_DESC(irq_sense, "IRQ sense: low level=2, falling edge=0 "
 		"(default=2)");
+#endif

 static const char udc_name[] = "m66592_udc";
 static const char *m66592_ep_name[] = {
@@ -360,6 +366,7 @@ static void m66592_ep_setting(struct m66
 			ep->fifosel = M66592_D0FIFOSEL;
 			ep->fifoctr = M66592_D0FIFOCTR;
 			ep->fifotrn = M66592_D0FIFOTRN;
+#if !defined(CONFIG_SUPERH_BUILT_IN_M66592)
 		} else if (m66592->num_dma == 1) {
 			m66592->num_dma++;
 			ep->use_dma = 1;
@@ -367,6 +374,7 @@ static void m66592_ep_setting(struct m66
 			ep->fifosel = M66592_D1FIFOSEL;
 			ep->fifoctr = M66592_D1FIFOCTR;
 			ep->fifotrn = M66592_D1FIFOTRN;
+#endif
 		} else {
 			ep->use_dma = 0;
 			ep->fifoaddr = M66592_CFIFO;
@@ -611,6 +619,28 @@ static void start_ep0(struct m66592_ep *
 	}
 }

+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+static void init_controller(struct m66592 *m66592)
+{
+	usbf_start_clock();
+	m66592_bset(m66592, M66592_HSE, M66592_SYSCFG);		/* High spd */
+	m66592_bclr(m66592, M66592_USBE, M66592_SYSCFG);
+	m66592_bclr(m66592, M66592_DPRPU, M66592_SYSCFG);
+	m66592_bset(m66592, M66592_USBE, M66592_SYSCFG);
+
+	/* This is a workaound for SH7722 2nd cut */
+	m66592_bset(m66592, 0x8000, M66592_DVSTCTR);
+	m66592_bset(m66592, 0x1000, M66592_TESTMODE);
+	m66592_bclr(m66592, 0x8000, M66592_DVSTCTR);
+
+	m66592_bset(m66592, M66592_INTL, M66592_INTENB1);
+
+	m66592_write(m66592, 0, M66592_CFBCFG);
+	m66592_write(m66592, 0, M66592_D0FBCFG);
+	m66592_bset(m66592, endian, M66592_CFBCFG);
+	m66592_bset(m66592, endian, M66592_D0FBCFG);
+}
+#else	/* #if defined(CONFIG_SUPERH_BUILT_IN_M66592) */
 static void init_controller(struct m66592 *m66592)
 {
 	m66592_bset(m66592, (vif & M66592_LDRV) | (endian & M66592_BIGEND),
@@ -636,9 +666,13 @@ static void init_controller(struct m6659
 	m66592_write(m66592, M66592_BURST | M66592_CPU_ADR_RD_WR,
 			M66592_DMA0CFG);
 }
+#endif	/* #if defined(CONFIG_SUPERH_BUILT_IN_M66592) */

 static void disable_controller(struct m66592 *m66592)
 {
+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+	usbf_stop_clock();
+#else
 	m66592_bclr(m66592, M66592_SCKE, M66592_SYSCFG);
 	udelay(1);
 	m66592_bclr(m66592, M66592_PLLC, M66592_SYSCFG);
@@ -646,15 +680,20 @@ static void disable_controller(struct m6
 	m66592_bclr(m66592, M66592_RCKE, M66592_SYSCFG);
 	udelay(1);
 	m66592_bclr(m66592, M66592_XCKE, M66592_SYSCFG);
+#endif
 }

 static void m66592_start_xclock(struct m66592 *m66592)
 {
+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+	usbf_start_clock();
+#else
 	u16 tmp;

 	tmp = m66592_read(m66592, M66592_SYSCFG);
 	if (!(tmp & M66592_XCKE))
 		m66592_bset(m66592, M66592_XCKE, M66592_SYSCFG);
+#endif
 }

 /*-------------------------------------------------------------------------*/
@@ -1142,6 +1181,19 @@ static irqreturn_t m66592_irq(int irq, v
 	intsts0 = m66592_read(m66592, M66592_INTSTS0);
 	intenb0 = m66592_read(m66592, M66592_INTENB0);

+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+	if (!intsts0 && !intenb0) {
+		/*
+		 * When USB clock stops, it cannot read register. Even if a
+		 * clock stops, the interrupt occurs. So this driver turn on
+		 * a clock by this timing and do re-reading of register.
+		 */
+		m66592_start_xclock(m66592);
+		intsts0 = m66592_read(m66592, M66592_INTSTS0);
+		intenb0 = m66592_read(m66592, M66592_INTENB0);
+	}
+#endif
+
 	savepipe = m66592_read(m66592, M66592_CFIFOSEL);

 	mask0 = intsts0 & intenb0;
@@ -1485,6 +1537,7 @@ static int __exit m66592_remove(struct p
 	iounmap(m66592->reg);
 	free_irq(platform_get_irq(pdev, 0), m66592);
 	m66592_free_request(&m66592->ep[0].ep, m66592->ep0_req);
+	usbf_stop_clock();
 	kfree(m66592);
 	return 0;
 }
diff -uprN a/drivers/usb/gadget/m66592-udc.h b/drivers/usb/gadget/m66592-udc.h
--- a/drivers/usb/gadget/m66592-udc.h	2007-10-24 12:50:57.000000000 +0900
+++ b/drivers/usb/gadget/m66592-udc.h	2007-11-22 18:10:22.000000000 +0900
@@ -72,6 +72,11 @@
 #define   M66592_P_TST_J	 0x0001		/* PERI TEST J */
 #define   M66592_P_TST_NORMAL	 0x0000		/* PERI Normal Mode */

+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+#define M66592_CFBCFG		0x0A
+#define M66592_D0FBCFG		0x0C
+#define M66592_LITTLE		0x0100	/* b8: Little endian mode */
+#else
 #define M66592_PINCFG		0x0A
 #define M66592_LDRV		0x8000	/* b15: Drive Current Adjust */
 #define M66592_BIGEND		0x0100	/* b8: Big endian mode */
@@ -91,6 +96,7 @@
 #define M66592_PKTM		0x0020	/* b5: Packet mode */
 #define M66592_DENDE		0x0010	/* b4: Dend enable */
 #define M66592_OBUS		0x0004	/* b2: OUTbus mode */
+#endif	/* #if defined(CONFIG_SUPERH_BUILT_IN_M66592) */

 #define M66592_CFIFO		0x10
 #define M66592_D0FIFO		0x14
@@ -103,9 +109,13 @@
 #define M66592_REW		0x4000	/* b14: Buffer rewind */
 #define M66592_DCLRM		0x2000	/* b13: DMA buffer clear mode */
 #define M66592_DREQE		0x1000	/* b12: DREQ output enable */
+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+#define M66592_MBW		0x0800	/* b11: Maximum bit width for FIFO */
+#else
 #define M66592_MBW		0x0400	/* b10: Maximum bit width for FIFO */
 #define   M66592_MBW_8		 0x0000   /*  8bit */
 #define   M66592_MBW_16		 0x0400   /* 16bit */
+#endif	/* #if defined(CONFIG_SUPERH_BUILT_IN_M66592) */
 #define M66592_TRENB		0x0200	/* b9: Transaction counter enable */
 #define M66592_TRCLR		0x0100	/* b8: Transaction counter clear */
 #define M66592_DEZPM		0x0080	/* b7: Zero-length packet mode */
@@ -530,8 +540,13 @@ static inline void m66592_read_fifo(stru
 {
 	unsigned long fifoaddr = (unsigned long)m66592->reg + offset;

+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+	len = (len + 3) / 4;
+	insl(fifoaddr, buf, len);
+#else
 	len = (len + 1) / 2;
 	insw(fifoaddr, buf, len);
+#endif
 }

 static inline void m66592_write(struct m66592 *m66592, u16 val,
@@ -545,6 +560,24 @@ static inline void m66592_write_fifo(str
 		void *buf, unsigned long len)
 {
 	unsigned long fifoaddr = (unsigned long)m66592->reg + offset;
+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+	unsigned long count;
+	unsigned char *pb;
+	int i;
+
+	count = len / 4;
+	outsl(fifoaddr, buf, count);
+
+	if (len & 0x00000003) {
+		pb = buf + count * 4;
+		for (i = 0; i < (len & 0x00000003); i++) {
+			if (m66592_read(m66592, M66592_CFBCFG))	/* little */
+				outb(pb[i], fifoaddr + (3 - i));
+			else
+				outb(pb[i], fifoaddr + i);
+		}
+	}
+#else
 	unsigned long odd = len & 0x0001;

 	len = len / 2;
@@ -553,6 +586,7 @@ static inline void m66592_write_fifo(str
 		unsigned char *p = buf + len*2;
 		outb(*p, fifoaddr);
 	}
+#endif	/* #if defined(CONFIG_SUPERH_BUILT_IN_M66592) */
 }

 static inline void m66592_mdfy(struct m66592 *m66592, u16 val, u16 pat,
@@ -570,6 +604,26 @@ static inline void m66592_mdfy(struct m6
 #define m66592_bset(m66592, val, offset)	\
 			m66592_mdfy(m66592, val, 0, offset)

+#if defined(CONFIG_SUPERH_BUILT_IN_M66592)
+#include <asm/io.h>
+#define MSTPCR2		0xA4150038	/* for SH7722 */
+#define MSTPCR2_USB	0x00000800
+
+static inline void usbf_start_clock(void)
+{
+	ctrl_outl(ctrl_inl(MSTPCR2) & ~MSTPCR2_USB, MSTPCR2);
+}
+
+static inline void usbf_stop_clock(void)
+{
+	ctrl_outl(ctrl_inl(MSTPCR2) | MSTPCR2_USB, MSTPCR2);
+}
+
+#else
+#define usbf_start_clock(x)
+#define usbf_stop_clock(x)
+#endif	/* if defined(CONFIG_SUPERH_BUILT_IN_M66592) */
+
 #endif	/* ifndef __M66592_UDC_H__ */



-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel