Re: [linux-usb-devel] [BUG] USB_PERSIST

"Raymano Garibaldi" <[email protected]>
Newsgroups gmane.linux.kernel,gmane.linux.usb.devel
Message-ID <[email protected]> 
Hi Alan,

Here's what I got after compiling kernel with CONFIG_USB_PERSIST and
CONFIG_USB_DEBUG both enabled. The attached files are:

config - shows the .config file used when compiling kernel 2.6.23.9

sysandmount.txt - shows mounts and the state of persist for all usb
devices right before suspending.

dmesg_attached.txt - dmesg right after resuming when the USB device
remained attached while machine was suspend

dmesg_detachedandreattached.txt - dmesg right after resuming when the
USB device was detached while suspended and then reattached before
resuming.

Thanks,
Raymano G.


On 11/26/07, Alan Stern <[email protected]> wrote:
> On Mon, 26 Nov 2007, Raymano Garibaldi wrote:
>
> > > Wait a minute.  You're saying that  USB Persist worked under 2.6.21
> > > because it wasn't available?  That makes no sense.  Besides, if you
> > > don't like USB Persist under 2.6.23, you can always eliminate it by
> > > turning off CONFIG_USB_PERSIST.
> > >
> >
> > I have tried this. Simply turning off CONFIG_USB_PERSIST doesn't work.
> > In this case the USB drive file system is unmounted on resume, even if
> > the drive remained plugged in during suspend.
>
> Something about this doesn't sound right.
>
> When you have CONFIG_USB_PERSIST enabled, do you remember to turn on
> the Persist feature for the root fs device by writing a "1" to the
> device's power/persist file in sysfs?
>
> Can you try building a kernel with CONFIG_USB_PERSIST and
> CONFIG_USB_DEBUG both enabled, and post the dmesg log from immediately
> after resuming?
>
> Alan Stern
>
>
config (application/octet-stream, 73.9 KB) - not displayed
sysandmount.txt (text/plain, 945 B) 
[root@myfaun sys]# find /sys -name "persist" -print
/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-6/power/persist
/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-7/power/persist
/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/power/persist
/sys/devices/pci0000:00/0000:00:1d.7/usb2/power/persist
/sys/devices/pci0000:00/0000:00:1d.3/usb5/power/persist
/sys/devices/pci0000:00/0000:00:1d.2/usb4/power/persist
/sys/devices/pci0000:00/0000:00:1d.1/usb3/power/persist
/sys/devices/pci0000:00/0000:00:1d.0/usb1/power/persist

[root@myfaun guest]# find /sys -name "persist" -exec cat {} \;
1
1
1
1
1
1
1
1

[root@myfaun sys]# mount
/dev/sda3 on / type ext3 (rw,noatime)
none on /proc type proc (rw)
none on /sys type sysfs (rw)
none on /dev type ramfs (rw)
none on /proc/bus/usb type usbfs (rw)
none on /dev/pts type devpts (rw)
none on /dev/shm type tmpfs (rw)
/dev/sdb1 on /media/disk type vfat (rw,nosuid,nodev,noatime,flush,uid=1000,utf8,shortname=lower)
dmesg_attached.txt (text/plain, 29.9 KB) 
b_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
usb 2-6: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: finish resume
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
Stopping tasks ... done.
Suspending console(s)
usb 2-6: usb suspend
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
usb 2-7: usb suspend
usb 2-1: usb suspend
hub 2-0:1.0: hub_suspend
usb usb2: bus suspend
ehci_hcd 0000:00:1d.7: suspend root hub
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
uhci_hcd 0000:00:1d.3: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
uhci_hcd 0000:00:1d.2: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
uhci_hcd 0000:00:1d.1: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
uhci_hcd 0000:00:1d.0: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6004.36 BogoMIPS (lpj=10003787)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
CPU1 is up
ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
Switched to high resolution mode on CPU 1
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
uhci_hcd 0000:00:1d.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: uhci_resume
uhci_hcd 0000:00:1d.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: uhci_resume
uhci_hcd 0000:00:1d.2: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: uhci_resume
uhci_hcd 0000:00:1d.3: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: uhci_resume
ehci_hcd 0000:00:1d.7: resume from PCI D3
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata2: port disabled. ignoring.
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata1.00: configured for UDMA/33
usb usb1: usb resume
usb usb1: wakeup_rh
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb 2-1: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
usb 2-7: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
usb 2-7: finish resume
sd 2:0:0:0: [sda] Starting disk
usb usb1: suspend_rh (auto-stop)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb usb3: usb resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
usb 2-6: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: finish resume
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
Stopping tasks ... done.
Suspending console(s)
usb 2-6: usb suspend
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
usb 2-7: usb suspend
usb 2-1: usb suspend
hub 2-0:1.0: hub_suspend
usb usb2: bus suspend
ehci_hcd 0000:00:1d.7: suspend root hub
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
uhci_hcd 0000:00:1d.3: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
uhci_hcd 0000:00:1d.2: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
uhci_hcd 0000:00:1d.1: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
uhci_hcd 0000:00:1d.0: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6004.38 BogoMIPS (lpj=10003811)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
CPU1 is up
ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
Switched to high resolution mode on CPU 1
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
uhci_hcd 0000:00:1d.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: uhci_resume
uhci_hcd 0000:00:1d.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: uhci_resume
uhci_hcd 0000:00:1d.2: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: uhci_resume
uhci_hcd 0000:00:1d.3: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: uhci_resume
ehci_hcd 0000:00:1d.7: resume from PCI D3
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata2: port disabled. ignoring.
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ata4: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata1.00: configured for UDMA/33
usb usb1: usb resume
usb usb1: wakeup_rh
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb 2-1: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
usb 2-7: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
usb 2-7: finish resume
sd 2:0:0:0: [sda] Starting disk
usb usb1: suspend_rh (auto-stop)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb usb3: usb resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
usb 2-6: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: finish resume
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
Stopping tasks ... done.
Suspending console(s)
usb 2-6: usb suspend
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
usb 2-7: usb suspend
usb 2-1: usb suspend
hub 2-0:1.0: hub_suspend
usb usb2: bus suspend
ehci_hcd 0000:00:1d.7: suspend root hub
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
uhci_hcd 0000:00:1d.3: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
uhci_hcd 0000:00:1d.2: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
uhci_hcd 0000:00:1d.1: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
uhci_hcd 0000:00:1d.0: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6004.35 BogoMIPS (lpj=10003766)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
CPU1 is up
ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
Switched to high resolution mode on CPU 1
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
uhci_hcd 0000:00:1d.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: uhci_resume
uhci_hcd 0000:00:1d.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: uhci_resume
uhci_hcd 0000:00:1d.2: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: uhci_resume
uhci_hcd 0000:00:1d.3: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: uhci_resume
ehci_hcd 0000:00:1d.7: resume from PCI D3
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata2: port disabled. ignoring.
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ata5: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata1.00: configured for UDMA/33
usb usb1: usb resume
usb usb1: wakeup_rh
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb 2-1: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
usb 2-7: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
usb 2-7: finish resume
sd 2:0:0:0: [sda] Starting disk
usb usb1: suspend_rh (auto-stop)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb usb3: usb resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6 status 0001.0501 after resume, 0
usb 2-6: can't resume, status -19
hub 2-0:1.0: logical disconnect on port 6
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
hub 2-0:1.0: state 7 ports 8 chg 0040 evt 0000
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-6: USB disconnect, address 8
usb 2-6: unregistering device
usb 2-6: usb_disable_device nuking all URBs
usb 2-6: unregistering interface 2-6:1.0
usb_endpoint usbdev2.8_ep81: ep_device_release called for usbdev2.8_ep81
usb_endpoint usbdev2.8_ep02: ep_device_release called for usbdev2.8_ep02
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: [sdb] READ CAPACITY failed
scsi 12:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00
scsi 12:0:0:0: [sdb] Sense not available.
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: [sdb] Write Protect is off
scsi 12:0:0:0: [sdb] Mode Sense: 00 00 00 00
scsi 12:0:0:0: [sdb] Assuming drive cache: write through
usb 2-6:1.0: uevent
usb 2-6:1.0: uevent
usb_endpoint usbdev2.8_ep00: ep_device_release called for usbdev2.8_ep00
usb 2-6: uevent
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11838) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11839) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11840) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11841) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11842) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11843) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11844) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11845) failed
ehci_hcd 0000:00:1d.7: port 6 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: new high speed USB device using ehci_hcd and address 9
ehci_hcd 0000:00:1d.7: port 6 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: default language 0x0409
usb 2-6: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-6: Product: Flash Disk
usb 2-6: Manufacturer: USB 2.0
usb 2-6: SerialNumber: AA04012700008519
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
usb 2-6:1.0: uevent
usb 2-6:1.0: uevent
usb-storage 2-6:1.0: usb_probe_interface
usb-storage 2-6:1.0: usb_probe_interface - got id
scsi13 : SCSI emulation for USB Mass Storage devices
drivers/usb/core/inode.c: creating file '009'
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
scsi 13:0:0:0: Direct-Access     USB 2.0  Flash Disk       1100 PQ: 0 ANSI: 0 CCS
sd 13:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
sd 13:0:0:0: [sdb] Write Protect is off
sd 13:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 13:0:0:0: [sdb] Assuming drive cache: write through
sd 13:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
sd 13:0:0:0: [sdb] Write Protect is off
sd 13:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 13:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1 sdb2
sd 13:0:0:0: [sdb] Attached SCSI removable disk
sd 13:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
Stopping tasks ... done.
Suspending console(s)
usb 2-6: usb suspend
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
usb 2-7: usb suspend
usb 2-1: usb suspend
hub 2-0:1.0: hub_suspend
usb usb2: bus suspend
ehci_hcd 0000:00:1d.7: suspend root hub
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
uhci_hcd 0000:00:1d.3: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
uhci_hcd 0000:00:1d.2: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
uhci_hcd 0000:00:1d.1: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
uhci_hcd 0000:00:1d.0: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6004.34 BogoMIPS (lpj=10003759)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
CPU1 is up
ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
Switched to high resolution mode on CPU 1
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
uhci_hcd 0000:00:1d.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: uhci_resume
uhci_hcd 0000:00:1d.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: uhci_resume
uhci_hcd 0000:00:1d.2: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: uhci_resume
uhci_hcd 0000:00:1d.3: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: uhci_resume
ehci_hcd 0000:00:1d.7: resume from PCI D3
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata2: port disabled. ignoring.
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ata4: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata1.00: configured for UDMA/33
usb usb1: usb resume
usb usb1: wakeup_rh
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb 2-1: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
usb 2-7: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
usb 2-7: finish resume
sd 2:0:0:0: [sda] Starting disk
usb usb1: suspend_rh (auto-stop)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb usb3: usb resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
usb 2-6: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: finish resume
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
dmesg_detachedandreattached.txt (text/plain, 29.9 KB) 
PI: Unable to turn cooling device [dfe0cdc8] 'off'
Switched to high resolution mode on CPU 1
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
uhci_hcd 0000:00:1d.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: uhci_resume
uhci_hcd 0000:00:1d.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: uhci_resume
uhci_hcd 0000:00:1d.2: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: uhci_resume
uhci_hcd 0000:00:1d.3: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: uhci_resume
ehci_hcd 0000:00:1d.7: resume from PCI D3
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata2: port disabled. ignoring.
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ata4: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata1.00: configured for UDMA/33
usb usb1: usb resume
usb usb1: wakeup_rh
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb 2-1: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
usb 2-7: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
usb 2-7: finish resume
sd 2:0:0:0: [sda] Starting disk
usb usb1: suspend_rh (auto-stop)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb usb3: usb resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
usb 2-6: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: finish resume
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
Stopping tasks ... done.
Suspending console(s)
usb 2-6: usb suspend
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
usb 2-7: usb suspend
usb 2-1: usb suspend
hub 2-0:1.0: hub_suspend
usb usb2: bus suspend
ehci_hcd 0000:00:1d.7: suspend root hub
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
uhci_hcd 0000:00:1d.3: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
uhci_hcd 0000:00:1d.2: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
uhci_hcd 0000:00:1d.1: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
uhci_hcd 0000:00:1d.0: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6004.35 BogoMIPS (lpj=10003766)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
CPU1 is up
ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
Switched to high resolution mode on CPU 1
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
uhci_hcd 0000:00:1d.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: uhci_resume
uhci_hcd 0000:00:1d.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: uhci_resume
uhci_hcd 0000:00:1d.2: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: uhci_resume
uhci_hcd 0000:00:1d.3: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: uhci_resume
ehci_hcd 0000:00:1d.7: resume from PCI D3
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata2: port disabled. ignoring.
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ata5: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata1.00: configured for UDMA/33
usb usb1: usb resume
usb usb1: wakeup_rh
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb 2-1: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
usb 2-7: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
usb 2-7: finish resume
sd 2:0:0:0: [sda] Starting disk
usb usb1: suspend_rh (auto-stop)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb usb3: usb resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6 status 0001.0501 after resume, 0
usb 2-6: can't resume, status -19
hub 2-0:1.0: logical disconnect on port 6
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
hub 2-0:1.0: state 7 ports 8 chg 0040 evt 0000
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-6: USB disconnect, address 8
usb 2-6: unregistering device
usb 2-6: usb_disable_device nuking all URBs
usb 2-6: unregistering interface 2-6:1.0
usb_endpoint usbdev2.8_ep81: ep_device_release called for usbdev2.8_ep81
usb_endpoint usbdev2.8_ep02: ep_device_release called for usbdev2.8_ep02
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: [sdb] READ CAPACITY failed
scsi 12:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00
scsi 12:0:0:0: [sdb] Sense not available.
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: [sdb] Write Protect is off
scsi 12:0:0:0: [sdb] Mode Sense: 00 00 00 00
scsi 12:0:0:0: [sdb] Assuming drive cache: write through
usb 2-6:1.0: uevent
usb 2-6:1.0: uevent
usb_endpoint usbdev2.8_ep00: ep_device_release called for usbdev2.8_ep00
usb 2-6: uevent
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11838) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11839) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11840) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11841) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11842) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11843) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11844) failed
scsi 12:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11845) failed
ehci_hcd 0000:00:1d.7: port 6 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: new high speed USB device using ehci_hcd and address 9
ehci_hcd 0000:00:1d.7: port 6 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: default language 0x0409
usb 2-6: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-6: Product: Flash Disk
usb 2-6: Manufacturer: USB 2.0
usb 2-6: SerialNumber: AA04012700008519
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
usb 2-6:1.0: uevent
usb 2-6:1.0: uevent
usb-storage 2-6:1.0: usb_probe_interface
usb-storage 2-6:1.0: usb_probe_interface - got id
scsi13 : SCSI emulation for USB Mass Storage devices
drivers/usb/core/inode.c: creating file '009'
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
scsi 13:0:0:0: Direct-Access     USB 2.0  Flash Disk       1100 PQ: 0 ANSI: 0 CCS
sd 13:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
sd 13:0:0:0: [sdb] Write Protect is off
sd 13:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 13:0:0:0: [sdb] Assuming drive cache: write through
sd 13:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
sd 13:0:0:0: [sdb] Write Protect is off
sd 13:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 13:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1 sdb2
sd 13:0:0:0: [sdb] Attached SCSI removable disk
sd 13:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
Stopping tasks ... done.
Suspending console(s)
usb 2-6: usb suspend
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
usb 2-7: usb suspend
usb 2-1: usb suspend
hub 2-0:1.0: hub_suspend
usb usb2: bus suspend
ehci_hcd 0000:00:1d.7: suspend root hub
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
uhci_hcd 0000:00:1d.3: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
uhci_hcd 0000:00:1d.2: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
uhci_hcd 0000:00:1d.1: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
uhci_hcd 0000:00:1d.0: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6004.34 BogoMIPS (lpj=10003759)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
CPU1 is up
ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
Switched to high resolution mode on CPU 1
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
uhci_hcd 0000:00:1d.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: uhci_resume
uhci_hcd 0000:00:1d.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: uhci_resume
uhci_hcd 0000:00:1d.2: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: uhci_resume
uhci_hcd 0000:00:1d.3: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: uhci_resume
ehci_hcd 0000:00:1d.7: resume from PCI D3
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata2: port disabled. ignoring.
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ata4: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata1.00: configured for UDMA/33
usb usb1: usb resume
usb usb1: wakeup_rh
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb 2-1: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
usb 2-7: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
usb 2-7: finish resume
sd 2:0:0:0: [sda] Starting disk
usb usb1: suspend_rh (auto-stop)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb usb3: usb resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
usb 2-6: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: finish resume
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
Stopping tasks ... done.
Suspending console(s)
usb 2-6: usb suspend
sd 2:0:0:0: [sda] Synchronizing SCSI cache
sd 2:0:0:0: [sda] Stopping disk
usb 2-7: usb suspend
usb 2-1: usb suspend
hub 2-0:1.0: hub_suspend
usb usb2: bus suspend
ehci_hcd 0000:00:1d.7: suspend root hub
ACPI handle has no context!
ACPI handle has no context!
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
ehci_hcd 0000:00:1d.7: --> PCI D3/wakeup
uhci_hcd 0000:00:1d.3: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.3 disabled
uhci_hcd 0000:00:1d.3: --> PCI D0/legacy
uhci_hcd 0000:00:1d.2: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.2 disabled
uhci_hcd 0000:00:1d.2: --> PCI D0/legacy
uhci_hcd 0000:00:1d.1: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
uhci_hcd 0000:00:1d.1: --> PCI D0/legacy
uhci_hcd 0000:00:1d.0: uhci_suspend
ACPI: PCI interrupt for device 0000:00:1d.0 disabled
uhci_hcd 0000:00:1d.0: --> PCI D0/legacy
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Back to C!
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6004.36 BogoMIPS (lpj=10003778)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000e49d 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 3.00GHz stepping 05
CPU1 is up
ACPI: Unable to turn cooling device [dfe0cdc8] 'off'
Switched to high resolution mode on CPU 1
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:1b.0 at offset f (was 100, writing 105)
PM: Writing back config space on device 0000:00:1b.0 at offset 4 (was 4, writing fdff8004)
PM: Writing back config space on device 0000:00:1b.0 at offset 3 (was 0, writing 8)
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100000, writing 100002)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
uhci_hcd 0000:00:1d.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: uhci_resume
uhci_hcd 0000:00:1d.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: uhci_resume
uhci_hcd 0000:00:1d.2: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: uhci_resume
uhci_hcd 0000:00:1d.3: PCI legacy resume
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: uhci_resume
ehci_hcd 0000:00:1d.7: resume from PCI D3
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1d.7 at offset f (was 100, writing 107)
PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing fdfff000)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.1 at offset 8 (was f001, writing fa01)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata2: port disabled. ignoring.
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
pnp: Failed to activate device 00:07.
pnp: Failed to activate device 00:08.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ata5: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata1.00: configured for UDMA/33
usb usb1: usb resume
usb usb1: wakeup_rh
hub 1-0:1.0: hub_resume
usb usb2: usb resume
ehci_hcd 0000:00:1d.7: resume root hub
hub 2-0:1.0: hub_resume
usb 2-1: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 2-1: finish resume
usb 2-7: usb resume
ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001005 POWER sig=se0 PE CONNECT
usb 2-7: finish resume
sd 2:0:0:0: [sda] Starting disk
usb usb1: suspend_rh (auto-stop)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: configured for UDMA/100
sd 2:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb usb3: usb resume
usb usb3: wakeup_rh
hub 3-0:1.0: hub_resume
usb usb4: usb resume
usb usb4: wakeup_rh
hub 4-0:1.0: hub_resume
usb usb5: usb resume
usb usb5: wakeup_rh
hub 5-0:1.0: hub_resume
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6 status 0001.0501 after resume, 0
usb 2-6: can't resume, status -19
hub 2-0:1.0: logical disconnect on port 6
Restarting tasks ... <7>hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
done.
hub 2-0:1.0: state 7 ports 8 chg 0040 evt 0000
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-6: USB disconnect, address 9
usb 2-6: unregistering device
usb 2-6: usb_disable_device nuking all URBs
usb 2-6: unregistering interface 2-6:1.0
usb_endpoint usbdev2.9_ep81: ep_device_release called for usbdev2.9_ep81
usb_endpoint usbdev2.9_ep02: ep_device_release called for usbdev2.9_ep02
sd 13:0:0:0: [sdb] READ CAPACITY failed
sd 13:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00
scsi 13:0:0:0: [sdb] Sense not available.
scsi 13:0:0:0: [sdb] Write Protect is off
scsi 13:0:0:0: [sdb] Mode Sense: 00 00 00 00
scsi 13:0:0:0: [sdb] Assuming drive cache: write through
usb 2-6:1.0: uevent
usb 2-6:1.0: uevent
usb_endpoint usbdev2.9_ep00: ep_device_release called for usbdev2.9_ep00
usb 2-6: uevent
scsi 13:0:0:0: rejecting I/O to dead device
scsi 13:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11838) failed
scsi 13:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11839) failed
scsi 13:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11840) failed
scsi 13:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11841) failed
scsi 13:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11842) failed
scsi 13:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11843) failed
scsi 13:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11844) failed
scsi 13:0:0:0: rejecting I/O to dead device
FAT: Directory bread(block 11845) failed
ehci_hcd 0000:00:1d.7: port 6 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: new high speed USB device using ehci_hcd and address 10
ehci_hcd 0000:00:1d.7: port 6 high speed
ehci_hcd 0000:00:1d.7: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-6: default language 0x0409
usb 2-6: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-6: Product: Flash Disk
usb 2-6: Manufacturer: USB 2.0
usb 2-6: SerialNumber: AA04012700008519
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
usb 2-6:1.0: uevent
usb 2-6:1.0: uevent
usb-storage 2-6:1.0: usb_probe_interface
usb-storage 2-6:1.0: usb_probe_interface - got id
scsi14 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 10
usb-storage: waiting for device to settle before scanning
drivers/usb/core/inode.c: creating file '010'
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
usb usb3: suspend_rh (auto-stop)
usb usb4: suspend_rh (auto-stop)
usb usb5: suspend_rh (auto-stop)
hub 1-0:1.0: hub_suspend
usb usb1: bus auto-suspend
usb usb1: suspend_rh
hub 3-0:1.0: hub_suspend
usb usb3: bus auto-suspend
usb usb3: suspend_rh
hub 4-0:1.0: hub_suspend
usb usb4: bus auto-suspend
usb usb4: suspend_rh
hub 5-0:1.0: hub_suspend
usb usb5: bus auto-suspend
usb usb5: suspend_rh
scsi 14:0:0:0: Direct-Access     USB 2.0  Flash Disk       1100 PQ: 0 ANSI: 0 CCS
sd 14:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
sd 14:0:0:0: [sdb] Write Protect is off
sd 14:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 14:0:0:0: [sdb] Assuming drive cache: write through
sd 14:0:0:0: [sdb] 7928832 512-byte hardware sectors (4060 MB)
sd 14:0:0:0: [sdb] Write Protect is off
sd 14:0:0:0: [sdb] Mode Sense: 43 00 00 00
sd 14:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1 sdb2
sd 14:0:0:0: [sdb] Attached SCSI removable disk
sd 14:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.