Re: The problems of OHCI driver for Winbond W90N740.

On Tue, 2 Oct 2007, Darwin Chen wrote:

> Hello,
> I'm porting uClinux for W90N740, the kernel is booted successful, but the USB Host has some problems. After the kernel is booted, I plug in a USB Card reader, the kernel outputs the following messages, I don't understand the messages, :(
> The attachment is the HCD source code for W90N740. 
> $ cat /proc/kmsg &

> <7>usb-storage: Command READ_CAPACITY (10 bytes)
> <7>usb-storage:  25 00 00 00 00 00 00 00 00 00
> <7>usb-storage: Bulk Command S 0x43425355 T 0x5 L 8 F 128 Trg 0 LUN 0 CL 10
> <7>usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
> <7>drivers/usb/host/ohci-dbg.c: SUB 00336738 dev=2 ep=1out-bulk flags=c len=0/31 stat=-115
> <7>drivers/usb/host/ohci-dbg.c: data(0/31): 55 53 42 43 05 00 00 00 08 00 00 00 80 00 0a 25... stat:-115
> <7>drivers/usb/host/ohci-dbg.c: RET 00336738 dev=2 ep=1out-bulk flags=c len=31/31 stat=0
> <7>usb-storage: Status code 0; transferred 31/31
> <7>usb-storage: -- transfer complete
> <7>usb-storage: Bulk command transfer result=0
> <7>usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
> <7>drivers/usb/host/ohci-dbg.c: SUB 0032cdb8 dev=2 ep=2in-bulk flags=5 len=0/8 stat=-115
> <7>drivers/usb/host/ohci-dbg.c: RET 0032cdb8 dev=2 ep=2in-bulk flags=5 len=8/8 stat=0
> <7>drivers/usb/host/ohci-dbg.c: data(8/8): 00 01 f5 ff 00 00 02 00 stat:0
> <7>usb-storage: Status code 0; transferred 8/8
> <7>usb-storage: -- transfer complete
> <7>usb-storage: Bulk data transfer result 0x0
> <7>usb-storage: Attempting to get CSW...
> <7>usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
> <7>drivers/usb/host/ohci-dbg.c: SUB 00336738 dev=2 ep=2in-bulk flags=c len=0/13 stat=-115
> 
> $ <7>usb-storage: command_abort called
> <7>usb-storage: usb_stor_stop_transport called
> <7>usb-storage: -- cancelling URB
> <7>drivers/usb/host/ohci-dbg.c: UNLINK 00336738 dev=2 ep=2in-bulk flags=c len=0/13 stat=-104
> 
> There is nothing in /proc/bus/usb!
> 
> What should I do?

First, make sure /proc/bus/usb is mounted:

	mount -t usbfs none /proc/bus/usb

Second, try plugging the card reader into a regular Linux system to
make sure it is okay.

Third, try plugging a different USB device (like a flash memory) into 
your machine, instead of the card reader.

The error message means that Linux didn't receive a status reply from 
the card reader after sending it a READ CAPACITY command.  Either the 
card reader didn't send a status reply or else the host controller 
driver didn't detect the reply.

Alan Stern


-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users