Re: smartctl output for Crucial 512Gb SSD
| Newsgroups | gmane.linux.utilities.smartmontools |
|---|---|
| Message-ID | <[email protected]> |
Well, the first two things that jump out at me are the version of smartcontrol and the database. 5.41 is quite old. Try using the newest, which is IIRC, 6.3. You might also try updating the database. Re-run that and see what happens. > Hi > > My m4 512Gb CT512M4SSD1 suddenly failed to read. Below is the smartctl > output that returns eventually, taking at least a couple of minutes. I've > tried 2 different USB caddys and also SATA connection to laptop running > livecd. The drive has exclusively been mounted read-only on a Linux > system > with an ext4 filesystem, and has had unexpected power loss routinely > throughout its life. The values in the attribute table look OK to me I > think, but the serious errors at the bottom look bad. Any ideas greatly > appreciated: > > > > root@w530:/dev# smartctl --all /dev/sdb > smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.8.0-41-generic] (local > build) > Copyright (C) 2002-11 by Bruce Allen,http:// > <http://smartmontools.sourceforge.net/>smartmontools.sourceforge.net > > === START OF INFORMATION SECTION === > Device Model: M4-CT512M4SSD1 > *removed personal information* > LU WWN Device Id: 5 00a075 1091fcc21 > Firmware Version: 070H > User Capacity: 512,110,190,592 bytes [512 GB] > Sector Size: 512 bytes logical/physical > Device is: Not in smartctl database [for details use: -P showall] > ATA Version is: 8 > ATA Standard is: ATA-8-ACS revision 6 > Local Time is: Tue Aug 12 12:02:50 2014 BST > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > Warning: This result is based on an Attribute check. > > General SMART Values: > Offline data collection status: (0x80) Offline data collection > activity > was never started. > Auto Offline Data Collection: Enabled. > Self-test execution status: ( 0) The previous self-test routine > completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: ( 2380) seconds. > Offline data collection > capabilities: (0x7b) SMART execute Offline immediate. > Auto Offline data collection on/off support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before > entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 39) minutes. > Conveyance self-test routine > recommended polling time: ( 3) minutes. > SCT capabilities: (0x003d) SCT Status supported. > SCT Error Recovery Control supported. > SCT Feature Control supported. > SCT Data Table supported. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x002f 100 100 050 Pre-fail > Always - 0 > 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail > Always - 0 > 9 Power_On_Hours 0x0032 100 100 001 Old_age > Always - 4439 > 12 Power_Cycle_Count 0x0032 100 100 001 Old_age > Always - 515 > 170 Unknown_Attribute 0x0033 100 100 010 Pre-fail > Always - 0 > 171 Unknown_Attribute 0x0032 100 100 001 Old_age > Always - 0 > 172 Unknown_Attribute 0x0032 100 100 001 Old_age > Always - 0 > 173 Unknown_Attribute 0x0033 100 100 010 Pre-fail > Always - 0 > 174 Unknown_Attribute 0x0032 100 100 001 Old_age > Always - 398 > 181 Program_Fail_Cnt_Total 0x0022 100 100 001 Old_age > Always - 618478239843 > 183 Runtime_Bad_Block 0x0032 100 100 001 Old_age > Always - 0 > 184 End-to-End_Error 0x0033 100 100 050 Pre-fail > Always - 0 > 187 Reported_Uncorrect 0x0032 100 100 001 Old_age > Always - 0 > 188 Command_Timeout 0x0032 100 100 001 Old_age > Always - 0 > 189 High_Fly_Writes 0x000e 100 100 001 Old_age > Always - 215 > 194 Temperature_Celsius 0x0022 100 100 000 Old_age > Always - 0 > 195 Hardware_ECC_Recovered 0x003a 100 100 001 Old_age > Always - 0 > 196 Reallocated_Event_Count 0x0032 100 100 001 Old_age > Always - 0 > 197 Current_Pending_Sector 0x0032 100 100 001 Old_age > Always - 0 > 198 Offline_Uncorrectable 0x0030 100 100 001 Old_age > Offline - 0 > 199 UDMA_CRC_Error_Count 0x0032 100 100 001 Old_age > Always - 0 > 202 Data_Address_Mark_Errs 0x0018 100 100 001 Old_age > Offline - 0 > 206 Flying_Height 0x000e 100 100 001 Old_age > Always - 0 > > Read SMART Log Directory failed. > > Error SMART Error Log Read failed: scsi error medium or hardware error > (serious) > Smartctl: SMART Error Log Read Failed > Error SMART Error Self-Test Log Read failed: scsi error medium or hardware > error (serious) > Smartctl: SMART Self Test Log Read Failed > Error SMART Read Selective Self-Test Log failed: scsi error medium or > hardware error (serious) > Smartctl: SMART Selective Self Test Log Read Failed > ------------------------------------------------------------------------------ > _______________________________________________ > Smartmontools-support mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/smartmontools-support > ------------------------------------------------------------------------------