Re: smartd and smartctl - SMART sta tus command failure
Naveen <[email protected]> Tue, 31 May 2016 05:35:31 +0000 (UTC)
| Newsgroups | gmane.linux.utilities.smartmontools |
|---|---|
| Message-ID | <[email protected]> |
Naveen <Naveen.Chandrasekaran <at> radisys.com> writes:
>
> Appreciate your help and Thanks in advance. The log files attached with this
> mail are reported with debug and ioctl options.
>
>
>
Additional logs below the gmane page wasn't allowing to attach to original post:
[root@8198b5e51d85 /]# smartctl --all /dev/sdc
smartctl 6.4 2015-06-04 r4109 [x86_64-linux-3.10.0-327.13.1.el7.x86_64]
(local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HGST HUS726060ALN610
Serial Number: NAHYUEUX
LU WWN Device Id: 5 000cca 242dba5c9
Firmware Version: APGNT7J0
User Capacity: 6,001,175,126,016 bytes [6.00 TB]
Sector Size: 4096 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri May 27 13:36:36 2016 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
SMART Status not supported: Invalid ATA output register values
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 113) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 774) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always
- 0
2 Throughput_Performance 0x0005 138 138 054 Pre-fail Offline
- 100
3 Spin_Up_Time 0x0007 166 166 024 Pre-fail Always
- 379 (Average 414)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always
- 34
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always
- 0
8 Seek_Time_Performance 0x0005 128 128 020 Pre-fail Offline
- 18
9 Power_On_Hours 0x0012 100 100 000 Old_age Always
- 1184
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 34
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 55
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always
- 55
194 Temperature_Celsius 0x0002 206 206 000 Old_age Always
- 29 (Min/Max 19/51)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always
- 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@8198b5e51d85 /]# smartctl -H /dev/sdc -r ioctl,2 -T permissive
smartctl 6.4 2015-06-04 r4109 [x86_64-linux-3.10.0-327.13.1.el7.x86_64]
(local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
[inquiry: 12 00 00 00 24 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=0 milliseconds resid=0
Incoming data, len=36:
00 00 00 06 12 45 00 00 02 41 54 41 20 20 20 20 20
10 48 47 53 54 20 48 55 53 37 32 36 30 36 30 41 4c
20 54 37 4a 30
[ata pass-through(16): 85 08 0e 00 00 00 01 00 00 00 00 00 00 00 ec 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=0 milliseconds resid=0
Incoming data, len=512 [only first 256 bytes shown]:
00 5a 04 ff 3f 37 c8 10 00 00 00 00 00 3f 00 00 00
10 00 00 00 00 41 4e 59 48 45 55 58 55 20 20 20 20
20 20 20 20 20 20 20 20 20 03 00 00 00 38 00 50 41
30 4e 47 37 54 30 4a 47 48 54 53 48 20 53 55 32 37
40 30 36 30 36 4c 41 36 4e 30 31 20 20 20 20 20 20
50 20 20 20 20 20 20 20 20 20 20 20 20 20 20 02 80
60 00 40 00 2f 00 40 00 02 00 02 07 00 ff 3f 10 00
70 3f 00 10 fc fb 00 00 71 ff ff ff 0f 00 00 07 00
80 03 00 78 00 78 00 78 00 78 00 18 0c 00 00 00 00
90 00 00 00 00 00 00 1f 00 0e 97 36 00 de 0c 44 00
a0 fc 03 29 00 6b 74 69 7d 73 47 69 74 41 bc 73 47
b0 7f 40 3d 81 00 00 fe 00 fe ff 00 00 00 00 08 00
c0 ca 00 f9 00 10 27 00 00 96 1e 54 57 00 00 00 00
d0 ca 00 00 00 00 50 87 5a 00 50 a2 cc db 42 c9 a5
e0 00 00 00 00 00 00 00 00 00 00 00 08 00 00 dc 40
f0 9c 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00
REPORT-IOCTL: Device=/dev/sdc Command=IDENTIFY DEVICE
Input: FR=...., SC=0x01, LL=...., LM=...., LH=...., DEV=...., CMD=0xec IN
[ata pass-through(16): 85 08 0e 00 00 00 01 00 00 00 00 00 00 00 ec 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=0 milliseconds resid=0
Incoming data, len=512 [only first 256 bytes shown]:
00 5a 04 ff 3f 37 c8 10 00 00 00 00 00 3f 00 00 00
10 00 00 00 00 41 4e 59 48 45 55 58 55 20 20 20 20
20 20 20 20 20 20 20 20 20 03 00 00 00 38 00 50 41
30 4e 47 37 54 30 4a 47 48 54 53 48 20 53 55 32 37
40 30 36 30 36 4c 41 36 4e 30 31 20 20 20 20 20 20
50 20 20 20 20 20 20 20 20 20 20 20 20 20 20 02 80
60 00 40 00 2f 00 40 00 02 00 02 07 00 ff 3f 10 00
70 3f 00 10 fc fb 00 00 71 ff ff ff 0f 00 00 07 00
80 03 00 78 00 78 00 78 00 78 00 18 0c 00 00 00 00
90 00 00 00 00 00 00 1f 00 0e 97 36 00 de 0c 44 00
a0 fc 03 29 00 6b 74 69 7d 73 47 69 74 41 bc 73 47
b0 7f 40 3d 81 00 00 fe 00 fe ff 00 00 00 00 08 00
c0 ca 00 f9 00 10 27 00 00 96 1e 54 57 00 00 00 00
d0 ca 00 00 00 00 50 87 5a 00 50 a2 cc db 42 c9 a5
e0 00 00 00 00 00 00 00 00 00 00 00 08 00 00 dc 40
f0 9c 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[Duration: 0.001s]
REPORT-IOCTL: Device=/dev/sdc Command=IDENTIFY DEVICE returned 0
===== [IDENTIFY DEVICE] DATA START (BASE-16) =====
000-015: 5a 04 ff 3f 37 c8 10 00 00 00 00 00 3f 00 00 00 |Z..?7.......?...|
016-031: 00 00 00 00 41 4e 59 48 45 55 58 55 20 20 20 20 |....ANYHEUXU |
032-047: 20 20 20 20 20 20 20 20 03 00 00 00 38 00 50 41 | ....8.PA|
048-063: 4e 47 37 54 30 4a 47 48 54 53 48 20 53 55 32 37 |NG7T0JGHTSH SU27|
064-079: 30 36 30 36 4c 41 36 4e 30 31 20 20 20 20 20 20 |0606LA6N01 |
080-095: 20 20 20 20 20 20 20 20 20 20 20 20 20 20 02 80 | ..|
096-111: 00 40 00 2f 00 40 00 02 00 02 07 00 ff 3f 10 00 |.@./.@.......?..|
112-127: 3f 00 10 fc fb 00 00 71 ff ff ff 0f 00 00 07 00 |?......q........|
128-143: 03 00 78 00 78 00 78 00 78 00 18 0c 00 00 00 00 |..x.x.x.x.......|
144-159: 00 00 00 00 00 00 1f 00 0e 97 36 00 de 0c 44 00 |..........6...D.|
160-175: fc 03 29 00 6b 74 69 7d 73 47 69 74 41 bc 73 47 |..).kti}sGitA.sG|
176-191: 7f 40 3d 81 00 00 fe 00 fe ff 00 00 00 00 08 00 |.@=.............|
192-207: ca 00 f9 00 10 27 00 00 96 1e 54 57 00 00 00 00 |.....'....TW....|
208-223: ca 00 00 00 00 50 87 5a 00 50 a2 cc db 42 c9 a5 |.....P.Z.P...B..|
224-239: 00 00 00 00 00 00 00 00 00 00 00 08 00 00 dc 40 |...............@|
240-255: 9c 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |.@..............|
256-271: 01 00 0b 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 07 00 |................|
304-319: 4e 47 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |NG..............|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
368-383: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 3d 00 00 00 |............=...|
416-431: 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 |...@............|
432-447: 00 00 20 1c 00 00 00 00 00 00 00 00 7f 10 21 00 |.. ...........!.|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 96 1e 54 57 |..............TW|
464-479: 00 00 00 00 08 00 00 00 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a5 52 |...............R|
===== [IDENTIFY DEVICE] DATA END (512 Bytes) =====
REPORT-IOCTL: Device=/dev/sdc Command=SMART READ ATTRIBUTE VALUES
Input: FR=0xd0, SC=0x01, LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0 IN
[ata pass-through(16): 85 08 0e 00 d0 00 01 00 00 00 4f 00 c2 00 b0 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=12 milliseconds resid=0
Incoming data, len=512 [only first 256 bytes shown]:
00 10 00 01 0b 00 64 64 00 00 00 00 00 00 00 02 05
10 00 8a 8a 64 00 00 00 00 00 00 03 07 00 a6 a6 7b
20 01 9e 01 0a 00 00 04 12 00 64 64 22 00 00 00 00
30 00 00 05 33 00 64 64 00 00 00 00 00 00 00 07 0b
40 00 64 64 00 00 00 00 00 00 00 08 05 00 80 80 12
50 00 00 00 00 00 00 09 12 00 64 64 a5 04 00 00 00
60 00 00 0a 13 00 64 64 00 00 00 00 00 00 00 0c 32
70 00 64 64 22 00 00 00 00 00 00 c0 32 00 64 64 39
80 00 00 00 00 00 00 c1 12 00 64 64 39 00 00 00 00
90 00 00 c2 02 00 ce ce 1d 00 13 00 33 00 00 c4 32
a0 00 64 64 00 00 00 00 00 00 00 c5 22 00 64 64 00
b0 00 00 00 00 00 00 c6 08 00 64 64 00 00 00 00 00
c0 00 00 c7 0a 00 c8 c8 00 00 00 00 00 00 00 00 00
d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[Duration: 0.013s]
REPORT-IOCTL: Device=/dev/sdc Command=SMART READ ATTRIBUTE VALUES returned 0
===== [SMART READ ATTRIBUTE VALUES] DATA START (BASE-16) =====
000-015: 10 00 01 0b 00 64 64 00 00 00 00 00 00 00 02 05 |.....dd.........|
016-031: 00 8a 8a 64 00 00 00 00 00 00 03 07 00 a6 a6 7b |...d...........{|
032-047: 01 9e 01 0a 00 00 04 12 00 64 64 22 00 00 00 00 |.........dd"....|
048-063: 00 00 05 33 00 64 64 00 00 00 00 00 00 00 07 0b |...3.dd.........|
064-079: 00 64 64 00 00 00 00 00 00 00 08 05 00 80 80 12 |.dd.............|
080-095: 00 00 00 00 00 00 09 12 00 64 64 a5 04 00 00 00 |.........dd.....|
096-111: 00 00 0a 13 00 64 64 00 00 00 00 00 00 00 0c 32 |.....dd........2|
112-127: 00 64 64 22 00 00 00 00 00 00 c0 32 00 64 64 39 |.dd".......2.dd9|
128-143: 00 00 00 00 00 00 c1 12 00 64 64 39 00 00 00 00 |.........dd9....|
144-159: 00 00 c2 02 00 ce ce 1d 00 13 00 33 00 00 c4 32 |...........3...2|
160-175: 00 64 64 00 00 00 00 00 00 00 c5 22 00 64 64 00 |.dd........".dd.|
176-191: 00 00 00 00 00 00 c6 08 00 64 64 00 00 00 00 00 |.........dd.....|
192-207: 00 00 c7 0a 00 c8 c8 00 00 00 00 00 00 00 00 00 |................|
208-223: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
240-255: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
256-271: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 82 00 71 00 00 5b |............q..[|
368-383: 03 00 01 00 02 ff 00 06 03 00 00 00 00 00 00 00 |................|
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
432-447: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
464-479: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 46 |...............F|
===== [SMART READ ATTRIBUTE VALUES] DATA END (512 Bytes) =====
REPORT-IOCTL: Device=/dev/sdc Command=SMART READ ATTRIBUTE THRESHOLDS
Input: FR=0xd1, SC=0x01, LL=0x01, LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0 IN
[ata pass-through(16): 85 08 0e 00 d1 00 01 00 01 00 4f 00 c2 00 b0 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=3 milliseconds resid=0
Incoming data, len=512 [only first 256 bytes shown]:
00 10 00 01 10 00 00 00 00 00 00 00 00 00 00 02 36
10 00 00 00 00 00 00 00 00 00 00 03 18 00 00 00 00
20 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 00
30 00 00 05 05 00 00 00 00 00 00 00 00 00 00 07 43
40 00 00 00 00 00 00 00 00 00 00 08 14 00 00 00 00
50 00 00 00 00 00 00 09 00 00 00 00 00 00 00 00 00
60 00 00 0a 3c 00 00 00 00 00 00 00 00 00 00 0c 00
70 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00
80 00 00 00 00 00 00 c1 00 00 00 00 00 00 00 00 00
90 00 00 c2 00 00 00 00 00 00 00 00 00 00 00 c4 00
a0 00 00 00 00 00 00 00 00 00 00 c5 00 00 00 00 00
b0 00 00 00 00 00 00 c6 00 00 00 00 00 00 00 00 00
c0 00 00 c7 00 00 00 00 00 00 00 00 00 00 00 00 00
d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[Duration: 0.003s]
REPORT-IOCTL: Device=/dev/sdc Command=SMART READ ATTRIBUTE THRESHOLDS returned 0
===== [SMART READ ATTRIBUTE THRESHOLDS] DATA START (BASE-16) =====
000-015: 10 00 01 10 00 00 00 00 00 00 00 00 00 00 02 36 |...............6|
016-031: 00 00 00 00 00 00 00 00 00 00 03 18 00 00 00 00 |................|
032-047: 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 00 |................|
048-063: 00 00 05 05 00 00 00 00 00 00 00 00 00 00 07 43 |...............C|
064-079: 00 00 00 00 00 00 00 00 00 00 08 14 00 00 00 00 |................|
080-095: 00 00 00 00 00 00 09 00 00 00 00 00 00 00 00 00 |................|
096-111: 00 00 0a 3c 00 00 00 00 00 00 00 00 00 00 0c 00 |...<............|
112-127: 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00 |................|
128-143: 00 00 00 00 00 00 c1 00 00 00 00 00 00 00 00 00 |................|
144-159: 00 00 c2 00 00 00 00 00 00 00 00 00 00 00 c4 00 |................|
160-175: 00 00 00 00 00 00 00 00 00 00 c5 00 00 00 00 00 |................|
176-191: 00 00 00 00 00 00 c6 00 00 00 00 00 00 00 00 00 |................|
192-207: 00 00 c7 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
208-223: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
240-255: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
256-271: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
368-383: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
432-447: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
464-479: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 |...............d|
===== [SMART READ ATTRIBUTE THRESHOLDS] DATA END (512 Bytes) =====
=== START OF READ SMART DATA SECTION ===
REPORT-IOCTL: Device=/dev/sdc Command=SMART STATUS CHECK
Input: FR=0xda, SC=...., LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0
[ata pass-through(16): 85 06 2c 00 da 00 00 00 00 00 4f 00 c2 00 b0 00 ]
scsi_status=0x2, host_status=0x0, driver_status=0x8
info=0x1 duration=1 milliseconds resid=0
>>> Sense buffer, len=18:
00 70 00 01 00 00 00 00 0a 00 00 00 00 00 1d 00 00
10 00 00
status=2: sense_key=1 asc=0 ascq=1d
[Duration: 0.001s]
Output: ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
REPORT-IOCTL: Device=/dev/sdc Command=SMART STATUS CHECK returned -1
errno=38 [Invalid ATA output register values]
SMART Status not supported: Invalid ATA output register values
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
[root@8198b5e51d85 /]#
==========================================================================
[root@370fb07a328b /]# smartd -d -i 10
smartd 6.4 2015-06-04 r4109 [x86_64-linux-3.10.0-327.13.1.el7.x86_64] (local
build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
Opened configuration file /etc/smartmontools/smartd.conf
Configuration file /etc/smartmontools/smartd.conf was parsed, found
DEVICESCAN, scanning devices
glob(3) found no matches for pattern /dev/hd[a-t]
glob(3) found no matches for pattern /dev/sd[a-c][a-z]
Device: /dev/sda, type changed from 'scsi' to 'sat'
Device: /dev/sda [SAT], opened
Device: /dev/sda [SAT], SanDisk SD7SB7S010T1122, S/N:154727400144,
WWN:5-001b44-f120dbed0, FW:X3540000, 1.02 TB
Device: /dev/sda [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sda [SAT], not capable of SMART Health Status check
Device: /dev/sda [SAT], can't monitor Current_Pending_Sector count - no
Attribute 197
Device: /dev/sda [SAT], can't monitor Offline_Uncorrectable count - no
Attribute 198
Unable to register ATA device /dev/sda [SAT] at line 23 of file
/etc/smartmontools/smartd.conf
Device: /dev/sdb, type changed from 'scsi' to 'sat'
Device: /dev/sdb [SAT], opened
Device: /dev/sdb [SAT], SanDisk SD7SB7S010T1122, S/N:154727400083,
WWN:5-001b44-f120dbe93, FW:X3540000, 1.02 TB
Device: /dev/sdb [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdb [SAT], not capable of SMART Health Status check
Device: /dev/sdb [SAT], can't monitor Current_Pending_Sector count - no
Attribute 197
Device: /dev/sdb [SAT], can't monitor Offline_Uncorrectable count - no
Attribute 198
Unable to register ATA device /dev/sdb [SAT] at line 23 of file
/etc/smartmontools/smartd.conf
Device: /dev/sdc, type changed from 'scsi' to 'sat'
Device: /dev/sdc [SAT], opened
Device: /dev/sdc [SAT], HGST HUS726060ALN610, S/N:NAHYUEUX,
WWN:5-000cca-242dba5c9, FW:APGNT7J0, 6.00 TB
Device: /dev/sdc [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdc [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdc [SAT] at line 23 of file
/etc/smartmontools/smartd.conf
Device: /dev/sdd, type changed from 'scsi' to 'sat'
Device: /dev/sdd [SAT], opened
Device: /dev/sdd [SAT], HGST HUS726060ALN610, S/N:NAHYYRKX,
WWN:5-000cca-242dbb5dc, FW:APGNT7J0, 6.00 TB
Device: /dev/sdd [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdd [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdd [SAT] at line 23 of file
/etc/smartmontools/smartd.conf
...
... <<<<<<<<<<<<< almost 15 other drives listed reported same error as
above <<<<<<<<<<<<<<<<<
...
Device: /dev/sdr [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdr [SAT] at line 23 of file
/etc/smartmontools/smartd.conf
Device: /dev/sds, type changed from 'scsi' to 'sat'
Device: /dev/sds [SAT], opened
Device: /dev/sds [SAT], SanDisk SD7SB7S512G1122, S/N:154842401360,
WWN:5-001b44-f18e88650, FW:X3540000, 512 GB
Device: /dev/sds [SAT], not found in smartd database.
Device: /dev/sds [SAT], can't monitor Current_Pending_Sector count - no
Attribute 197
Device: /dev/sds [SAT], can't monitor Offline_Uncorrectable count - no
Attribute 198
Device: /dev/sds [SAT], is SMART capable. Adding to "monitor" list.
Monitoring 1 ATA and 0 SCSI devices
Device: /dev/sds [SAT], opened ATA device
^C
Signal INT - rereading configuration file /etc/smartmontools/smartd.conf
(CONTROL-\ quits)
^Z
[1]+ Stopped smartd -d -i 10
[root@370fb07a328b /]#
------------------------------------------------------------------------------
What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic
patterns at an interface-level. Reveals which users, apps, and protocols are
consuming the most bandwidth. Provides multi-vendor support for NetFlow,
J-Flow, sFlow and other flows. Make informed decisions using capacity
planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e