smartd and smartctl - SMART status command failure
Naveen Karthick Chandrasekaran <[email protected]> Mon, 30 May 2016 10:51:34 +0000
| Newsgroups | gmane.linux.utilities.smartmontools |
|---|---|
| Message-ID | <DM2PR08MB14018C3FC9BC8B5B15875B81F9450@DM2PR08MB1401.namprd08.prod.outlook.com> |
Hi, When I run smartctl it reported below error and same with smartd. It appears "smartctl" though failed the SMART status command, it checked the attribute threshold values and indicated "Disk is OK" but smartd doesn't do the latter and bails out as soon as SMART status command failed? Is that understanding correct? My questions are: 1) What causes the above error and any solutions to overcome this and monitor the drive? 2) Given the above error loks like "smartd" doesn't do any monitoring on the device hence if we still want to monitor the device can we modify it to check the attribute values similar to how smartctl does? Just as an experiment? 3)How to update the drives in the database since smartctl complains the drives are missing in its database. Appreciate your help and Thanks in advance. The log files attached with this mail are reported with debug and ioctl options. === START OF READ SMART DATA SECTION === SMART Status command failed Please get assistance from http://smartmontools.sourceforge.net/ Register values returned from SMART Status command are: ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00 SMART Status not supported: Invalid ATA output register values SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. Similarly smartd reported: Device: /dev/sdc, type changed from 'scsi' to 'sat' Device: /dev/sdc [SAT], opened Device: /dev/sdc [SAT], HGST HUS726060ALN610, S/N:NAHYUEUX, WWN:5-000cca-242dba5c9, FW:APGNT7J0, 6.00 TB Device: /dev/sdc [SAT], not found in smartd database. SMART Status command failed Please get assistance from http://smartmontools.sourceforge.net/ Register values returned from SMART Status command are: ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00 Device: /dev/sdc [SAT], not capable of SMART Health Status check Unable to register ATA device /dev/sdc [SAT] at line 23 of file /etc/smartmontools/smartd.conf -------------------------------------------------- Thanks & regards, Naveen Karthick.C ------------------------------------------------------------------------------ What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic patterns at an interface-level. Reveals which users, apps, and protocols are consuming the most bandwidth. Provides multi-vendor support for NetFlow, J-Flow, sFlow and other flows. Make informed decisions using capacity planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e _______________________________________________ Smartmontools-support mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/smartmontools-support
smartmontools_query_mail.txt
(text/plain, 45.3 KB)
[root@8198b5e51d85 /]# smartctl --all /dev/sdc
smartctl 6.4 2015-06-04 r4109 [x86_64-linux-3.10.0-327.13.1.el7.x86_64] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HGST HUS726060ALN610
Serial Number: NAHYUEUX
LU WWN Device Id: 5 000cca 242dba5c9
Firmware Version: APGNT7J0
User Capacity: 6,001,175,126,016 bytes [6.00 TB]
Sector Size: 4096 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri May 27 13:36:36 2016 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
SMART Status not supported: Invalid ATA output register values
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 113) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 774) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 138 138 054 Pre-fail Offline - 100
3 Spin_Up_Time 0x0007 166 166 024 Pre-fail Always - 379 (Average 414)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 34
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 128 128 020 Pre-fail Offline - 18
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1184
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 34
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 55
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 55
194 Temperature_Celsius 0x0002 206 206 000 Old_age Always - 29 (Min/Max 19/51)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[root@8198b5e51d85 /]# smartctl -H /dev/sdc -r ioctl,2 -T permissive
smartctl 6.4 2015-06-04 r4109 [x86_64-linux-3.10.0-327.13.1.el7.x86_64] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
[inquiry: 12 00 00 00 24 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=0 milliseconds resid=0
Incoming data, len=36:
00 00 00 06 12 45 00 00 02 41 54 41 20 20 20 20 20
10 48 47 53 54 20 48 55 53 37 32 36 30 36 30 41 4c
20 54 37 4a 30
[ata pass-through(16): 85 08 0e 00 00 00 01 00 00 00 00 00 00 00 ec 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=0 milliseconds resid=0
Incoming data, len=512 [only first 256 bytes shown]:
00 5a 04 ff 3f 37 c8 10 00 00 00 00 00 3f 00 00 00
10 00 00 00 00 41 4e 59 48 45 55 58 55 20 20 20 20
20 20 20 20 20 20 20 20 20 03 00 00 00 38 00 50 41
30 4e 47 37 54 30 4a 47 48 54 53 48 20 53 55 32 37
40 30 36 30 36 4c 41 36 4e 30 31 20 20 20 20 20 20
50 20 20 20 20 20 20 20 20 20 20 20 20 20 20 02 80
60 00 40 00 2f 00 40 00 02 00 02 07 00 ff 3f 10 00
70 3f 00 10 fc fb 00 00 71 ff ff ff 0f 00 00 07 00
80 03 00 78 00 78 00 78 00 78 00 18 0c 00 00 00 00
90 00 00 00 00 00 00 1f 00 0e 97 36 00 de 0c 44 00
a0 fc 03 29 00 6b 74 69 7d 73 47 69 74 41 bc 73 47
b0 7f 40 3d 81 00 00 fe 00 fe ff 00 00 00 00 08 00
c0 ca 00 f9 00 10 27 00 00 96 1e 54 57 00 00 00 00
d0 ca 00 00 00 00 50 87 5a 00 50 a2 cc db 42 c9 a5
e0 00 00 00 00 00 00 00 00 00 00 00 08 00 00 dc 40
f0 9c 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00
REPORT-IOCTL: Device=/dev/sdc Command=IDENTIFY DEVICE
Input: FR=...., SC=0x01, LL=...., LM=...., LH=...., DEV=...., CMD=0xec IN
[ata pass-through(16): 85 08 0e 00 00 00 01 00 00 00 00 00 00 00 ec 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=0 milliseconds resid=0
Incoming data, len=512 [only first 256 bytes shown]:
00 5a 04 ff 3f 37 c8 10 00 00 00 00 00 3f 00 00 00
10 00 00 00 00 41 4e 59 48 45 55 58 55 20 20 20 20
20 20 20 20 20 20 20 20 20 03 00 00 00 38 00 50 41
30 4e 47 37 54 30 4a 47 48 54 53 48 20 53 55 32 37
40 30 36 30 36 4c 41 36 4e 30 31 20 20 20 20 20 20
50 20 20 20 20 20 20 20 20 20 20 20 20 20 20 02 80
60 00 40 00 2f 00 40 00 02 00 02 07 00 ff 3f 10 00
70 3f 00 10 fc fb 00 00 71 ff ff ff 0f 00 00 07 00
80 03 00 78 00 78 00 78 00 78 00 18 0c 00 00 00 00
90 00 00 00 00 00 00 1f 00 0e 97 36 00 de 0c 44 00
a0 fc 03 29 00 6b 74 69 7d 73 47 69 74 41 bc 73 47
b0 7f 40 3d 81 00 00 fe 00 fe ff 00 00 00 00 08 00
c0 ca 00 f9 00 10 27 00 00 96 1e 54 57 00 00 00 00
d0 ca 00 00 00 00 50 87 5a 00 50 a2 cc db 42 c9 a5
e0 00 00 00 00 00 00 00 00 00 00 00 08 00 00 dc 40
f0 9c 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[Duration: 0.001s]
REPORT-IOCTL: Device=/dev/sdc Command=IDENTIFY DEVICE returned 0
===== [IDENTIFY DEVICE] DATA START (BASE-16) =====
000-015: 5a 04 ff 3f 37 c8 10 00 00 00 00 00 3f 00 00 00 |Z..?7.......?...|
016-031: 00 00 00 00 41 4e 59 48 45 55 58 55 20 20 20 20 |....ANYHEUXU |
032-047: 20 20 20 20 20 20 20 20 03 00 00 00 38 00 50 41 | ....8.PA|
048-063: 4e 47 37 54 30 4a 47 48 54 53 48 20 53 55 32 37 |NG7T0JGHTSH SU27|
064-079: 30 36 30 36 4c 41 36 4e 30 31 20 20 20 20 20 20 |0606LA6N01 |
080-095: 20 20 20 20 20 20 20 20 20 20 20 20 20 20 02 80 | ..|
096-111: 00 40 00 2f 00 40 00 02 00 02 07 00 ff 3f 10 00 |.@./.@.......?..|
112-127: 3f 00 10 fc fb 00 00 71 ff ff ff 0f 00 00 07 00 |?......q........|
128-143: 03 00 78 00 78 00 78 00 78 00 18 0c 00 00 00 00 |..x.x.x.x.......|
144-159: 00 00 00 00 00 00 1f 00 0e 97 36 00 de 0c 44 00 |..........6...D.|
160-175: fc 03 29 00 6b 74 69 7d 73 47 69 74 41 bc 73 47 |..).kti}sGitA.sG|
176-191: 7f 40 3d 81 00 00 fe 00 fe ff 00 00 00 00 08 00 |.@=.............|
192-207: ca 00 f9 00 10 27 00 00 96 1e 54 57 00 00 00 00 |.....'....TW....|
208-223: ca 00 00 00 00 50 87 5a 00 50 a2 cc db 42 c9 a5 |.....P.Z.P...B..|
224-239: 00 00 00 00 00 00 00 00 00 00 00 08 00 00 dc 40 |...............@|
240-255: 9c 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |.@..............|
256-271: 01 00 0b 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 07 00 |................|
304-319: 4e 47 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |NG..............|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
368-383: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 3d 00 00 00 |............=...|
416-431: 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 |...@............|
432-447: 00 00 20 1c 00 00 00 00 00 00 00 00 7f 10 21 00 |.. ...........!.|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 96 1e 54 57 |..............TW|
464-479: 00 00 00 00 08 00 00 00 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a5 52 |...............R|
===== [IDENTIFY DEVICE] DATA END (512 Bytes) =====
REPORT-IOCTL: Device=/dev/sdc Command=SMART READ ATTRIBUTE VALUES
Input: FR=0xd0, SC=0x01, LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0 IN
[ata pass-through(16): 85 08 0e 00 d0 00 01 00 00 00 4f 00 c2 00 b0 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=12 milliseconds resid=0
Incoming data, len=512 [only first 256 bytes shown]:
00 10 00 01 0b 00 64 64 00 00 00 00 00 00 00 02 05
10 00 8a 8a 64 00 00 00 00 00 00 03 07 00 a6 a6 7b
20 01 9e 01 0a 00 00 04 12 00 64 64 22 00 00 00 00
30 00 00 05 33 00 64 64 00 00 00 00 00 00 00 07 0b
40 00 64 64 00 00 00 00 00 00 00 08 05 00 80 80 12
50 00 00 00 00 00 00 09 12 00 64 64 a5 04 00 00 00
60 00 00 0a 13 00 64 64 00 00 00 00 00 00 00 0c 32
70 00 64 64 22 00 00 00 00 00 00 c0 32 00 64 64 39
80 00 00 00 00 00 00 c1 12 00 64 64 39 00 00 00 00
90 00 00 c2 02 00 ce ce 1d 00 13 00 33 00 00 c4 32
a0 00 64 64 00 00 00 00 00 00 00 c5 22 00 64 64 00
b0 00 00 00 00 00 00 c6 08 00 64 64 00 00 00 00 00
c0 00 00 c7 0a 00 c8 c8 00 00 00 00 00 00 00 00 00
d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[Duration: 0.013s]
REPORT-IOCTL: Device=/dev/sdc Command=SMART READ ATTRIBUTE VALUES returned 0
===== [SMART READ ATTRIBUTE VALUES] DATA START (BASE-16) =====
000-015: 10 00 01 0b 00 64 64 00 00 00 00 00 00 00 02 05 |.....dd.........|
016-031: 00 8a 8a 64 00 00 00 00 00 00 03 07 00 a6 a6 7b |...d...........{|
032-047: 01 9e 01 0a 00 00 04 12 00 64 64 22 00 00 00 00 |.........dd"....|
048-063: 00 00 05 33 00 64 64 00 00 00 00 00 00 00 07 0b |...3.dd.........|
064-079: 00 64 64 00 00 00 00 00 00 00 08 05 00 80 80 12 |.dd.............|
080-095: 00 00 00 00 00 00 09 12 00 64 64 a5 04 00 00 00 |.........dd.....|
096-111: 00 00 0a 13 00 64 64 00 00 00 00 00 00 00 0c 32 |.....dd........2|
112-127: 00 64 64 22 00 00 00 00 00 00 c0 32 00 64 64 39 |.dd".......2.dd9|
128-143: 00 00 00 00 00 00 c1 12 00 64 64 39 00 00 00 00 |.........dd9....|
144-159: 00 00 c2 02 00 ce ce 1d 00 13 00 33 00 00 c4 32 |...........3...2|
160-175: 00 64 64 00 00 00 00 00 00 00 c5 22 00 64 64 00 |.dd........".dd.|
176-191: 00 00 00 00 00 00 c6 08 00 64 64 00 00 00 00 00 |.........dd.....|
192-207: 00 00 c7 0a 00 c8 c8 00 00 00 00 00 00 00 00 00 |................|
208-223: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
240-255: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
256-271: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 82 00 71 00 00 5b |............q..[|
368-383: 03 00 01 00 02 ff 00 06 03 00 00 00 00 00 00 00 |................|
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
432-447: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
464-479: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 46 |...............F|
===== [SMART READ ATTRIBUTE VALUES] DATA END (512 Bytes) =====
REPORT-IOCTL: Device=/dev/sdc Command=SMART READ ATTRIBUTE THRESHOLDS
Input: FR=0xd1, SC=0x01, LL=0x01, LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0 IN
[ata pass-through(16): 85 08 0e 00 d1 00 01 00 01 00 4f 00 c2 00 b0 00 ]
scsi_status=0x0, host_status=0x0, driver_status=0x0
info=0x0 duration=3 milliseconds resid=0
Incoming data, len=512 [only first 256 bytes shown]:
00 10 00 01 10 00 00 00 00 00 00 00 00 00 00 02 36
10 00 00 00 00 00 00 00 00 00 00 03 18 00 00 00 00
20 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 00
30 00 00 05 05 00 00 00 00 00 00 00 00 00 00 07 43
40 00 00 00 00 00 00 00 00 00 00 08 14 00 00 00 00
50 00 00 00 00 00 00 09 00 00 00 00 00 00 00 00 00
60 00 00 0a 3c 00 00 00 00 00 00 00 00 00 00 0c 00
70 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00
80 00 00 00 00 00 00 c1 00 00 00 00 00 00 00 00 00
90 00 00 c2 00 00 00 00 00 00 00 00 00 00 00 c4 00
a0 00 00 00 00 00 00 00 00 00 00 c5 00 00 00 00 00
b0 00 00 00 00 00 00 c6 00 00 00 00 00 00 00 00 00
c0 00 00 c7 00 00 00 00 00 00 00 00 00 00 00 00 00
d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[Duration: 0.003s]
REPORT-IOCTL: Device=/dev/sdc Command=SMART READ ATTRIBUTE THRESHOLDS returned 0
===== [SMART READ ATTRIBUTE THRESHOLDS] DATA START (BASE-16) =====
000-015: 10 00 01 10 00 00 00 00 00 00 00 00 00 00 02 36 |...............6|
016-031: 00 00 00 00 00 00 00 00 00 00 03 18 00 00 00 00 |................|
032-047: 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 00 |................|
048-063: 00 00 05 05 00 00 00 00 00 00 00 00 00 00 07 43 |...............C|
064-079: 00 00 00 00 00 00 00 00 00 00 08 14 00 00 00 00 |................|
080-095: 00 00 00 00 00 00 09 00 00 00 00 00 00 00 00 00 |................|
096-111: 00 00 0a 3c 00 00 00 00 00 00 00 00 00 00 0c 00 |...<............|
112-127: 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00 |................|
128-143: 00 00 00 00 00 00 c1 00 00 00 00 00 00 00 00 00 |................|
144-159: 00 00 c2 00 00 00 00 00 00 00 00 00 00 00 c4 00 |................|
160-175: 00 00 00 00 00 00 00 00 00 00 c5 00 00 00 00 00 |................|
176-191: 00 00 00 00 00 00 c6 00 00 00 00 00 00 00 00 00 |................|
192-207: 00 00 c7 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
208-223: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
240-255: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
256-271: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
368-383: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
432-447: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
464-479: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 64 |...............d|
===== [SMART READ ATTRIBUTE THRESHOLDS] DATA END (512 Bytes) =====
=== START OF READ SMART DATA SECTION ===
REPORT-IOCTL: Device=/dev/sdc Command=SMART STATUS CHECK
Input: FR=0xda, SC=...., LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0
[ata pass-through(16): 85 06 2c 00 da 00 00 00 00 00 4f 00 c2 00 b0 00 ]
scsi_status=0x2, host_status=0x0, driver_status=0x8
info=0x1 duration=1 milliseconds resid=0
>>> Sense buffer, len=18:
00 70 00 01 00 00 00 00 0a 00 00 00 00 00 1d 00 00
10 00 00
status=2: sense_key=1 asc=0 ascq=1d
[Duration: 0.001s]
Output: ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
REPORT-IOCTL: Device=/dev/sdc Command=SMART STATUS CHECK returned -1 errno=38 [Invalid ATA output register values]
SMART Status not supported: Invalid ATA output register values
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
[root@8198b5e51d85 /]#
======================================================================================
[root@370fb07a328b /]# smartd -d -i 5
smartd 6.4 2015-06-04 r4109 [x86_64-linux-3.10.0-327.13.1.el7.x86_64] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
======> INVALID INTERVAL: 5 <=======
======> INTERVAL MUST BE INTEGER BETWEEN 10 AND 2147483647 <=======
Use smartd -h to get a usage summary
[root@370fb07a328b /]# smartd -d -i 10
smartd 6.4 2015-06-04 r4109 [x86_64-linux-3.10.0-327.13.1.el7.x86_64] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
Opened configuration file /etc/smartmontools/smartd.conf
Configuration file /etc/smartmontools/smartd.conf was parsed, found DEVICESCAN, scanning devices
glob(3) found no matches for pattern /dev/hd[a-t]
glob(3) found no matches for pattern /dev/sd[a-c][a-z]
Device: /dev/sda, type changed from 'scsi' to 'sat'
Device: /dev/sda [SAT], opened
Device: /dev/sda [SAT], SanDisk SD7SB7S010T1122, S/N:154727400144, WWN:5-001b44-f120dbed0, FW:X3540000, 1.02 TB
Device: /dev/sda [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sda [SAT], not capable of SMART Health Status check
Device: /dev/sda [SAT], can't monitor Current_Pending_Sector count - no Attribute 197
Device: /dev/sda [SAT], can't monitor Offline_Uncorrectable count - no Attribute 198
Unable to register ATA device /dev/sda [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdb, type changed from 'scsi' to 'sat'
Device: /dev/sdb [SAT], opened
Device: /dev/sdb [SAT], SanDisk SD7SB7S010T1122, S/N:154727400083, WWN:5-001b44-f120dbe93, FW:X3540000, 1.02 TB
Device: /dev/sdb [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdb [SAT], not capable of SMART Health Status check
Device: /dev/sdb [SAT], can't monitor Current_Pending_Sector count - no Attribute 197
Device: /dev/sdb [SAT], can't monitor Offline_Uncorrectable count - no Attribute 198
Unable to register ATA device /dev/sdb [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdc, type changed from 'scsi' to 'sat'
Device: /dev/sdc [SAT], opened
Device: /dev/sdc [SAT], HGST HUS726060ALN610, S/N:NAHYUEUX, WWN:5-000cca-242dba5c9, FW:APGNT7J0, 6.00 TB
Device: /dev/sdc [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdc [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdc [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdd, type changed from 'scsi' to 'sat'
Device: /dev/sdd [SAT], opened
Device: /dev/sdd [SAT], HGST HUS726060ALN610, S/N:NAHYYRKX, WWN:5-000cca-242dbb5dc, FW:APGNT7J0, 6.00 TB
Device: /dev/sdd [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdd [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdd [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sde, type changed from 'scsi' to 'sat'
Device: /dev/sde [SAT], opened
Device: /dev/sde [SAT], HGST HUS726060ALN610, S/N:NAHYSYHX, WWN:5-000cca-242dba02d, FW:APGNT7J0, 6.00 TB
Device: /dev/sde [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sde [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sde [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdf, type changed from 'scsi' to 'sat'
Device: /dev/sdf [SAT], opened
Device: /dev/sdf [SAT], HGST HUS726060ALN610, S/N:NAHYUDTX, WWN:5-000cca-242dba5a9, FW:APGNT7J0, 6.00 TB
Device: /dev/sdf [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdf [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdf [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdg, type changed from 'scsi' to 'sat'
Device: /dev/sdg [SAT], opened
Device: /dev/sdg [SAT], HGST HUS726060ALN610, S/N:NCG2A1VJ, WWN:5-000cca-24dc10e81, FW:APGNT7J0, 6.00 TB
Device: /dev/sdg [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdg [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdg [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdh, type changed from 'scsi' to 'sat'
Device: /dev/sdh [SAT], opened
Device: /dev/sdh [SAT], HGST HUS726060ALN610, S/N:NAHYUH6X, WWN:5-000cca-242dba5f4, FW:APGNT7J0, 6.00 TB
Device: /dev/sdh [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdh [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdh [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdi, type changed from 'scsi' to 'sat'
Device: /dev/sdi [SAT], opened
Device: /dev/sdi [SAT], HGST HUS726060ALN610, S/N:NAHYUM1X, WWN:5-000cca-242dba66b, FW:APGNT7J0, 6.00 TB
Device: /dev/sdi [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdi [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdi [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdj, type changed from 'scsi' to 'sat'
Device: /dev/sdj [SAT], opened
Device: /dev/sdj [SAT], HGST HUS726060ALN610, S/N:NCGJU9ML, WWN:5-000cca-24dc7a4f3, FW:APGNT7J0, 6.00 TB
Device: /dev/sdj [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdj [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdj [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdk, type changed from 'scsi' to 'sat'
Device: /dev/sdk [SAT], opened
Device: /dev/sdk [SAT], HGST HUS726060ALN610, S/N:NAHYUEJX, WWN:5-000cca-242dba5c0, FW:APGNT7J0, 6.00 TB
Device: /dev/sdk [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdk [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdk [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdl, type changed from 'scsi' to 'sat'
Device: /dev/sdl [SAT], opened
Device: /dev/sdl [SAT], HGST HUS726060ALN610, S/N:NAHYUJXX, WWN:5-000cca-242dba629, FW:APGNT7J0, 6.00 TB
Device: /dev/sdl [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdl [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdl [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdm, type changed from 'scsi' to 'sat'
Device: /dev/sdm [SAT], opened
Device: /dev/sdm [SAT], HGST HUS726060ALN610, S/N:NAHYUNLX, WWN:5-000cca-242dba69b, FW:APGNT7J0, 6.00 TB
Device: /dev/sdm [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdm [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdm [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdn, type changed from 'scsi' to 'sat'
Device: /dev/sdn [SAT], opened
Device: /dev/sdn [SAT], HGST HUS726060ALN610, S/N:NAHYUHKX, WWN:5-000cca-242dba5ff, FW:APGNT7J0, 6.00 TB
Device: /dev/sdn [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdn [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdn [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdo, type changed from 'scsi' to 'sat'
Device: /dev/sdo [SAT], opened
Device: /dev/sdo [SAT], HGST HUS726060ALN610, S/N:NAHXYAVX, WWN:5-000cca-242db4012, FW:APGNT7J0, 6.00 TB
Device: /dev/sdo [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdo [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdo [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdp, type changed from 'scsi' to 'sat'
Device: /dev/sdp [SAT], opened
Device: /dev/sdp [SAT], HGST HUS726060ALN610, S/N:NAHYUJ3X, WWN:5-000cca-242dba610, FW:APGNT7J0, 6.00 TB
Device: /dev/sdp [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdp [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdp [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdq, type changed from 'scsi' to 'sat'
Device: /dev/sdq [SAT], opened
Device: /dev/sdq [SAT], HGST HUS726060ALN610, S/N:NAHYUMYX, WWN:5-000cca-242dba687, FW:APGNT7J0, 6.00 TB
Device: /dev/sdq [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdq [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdq [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdr, type changed from 'scsi' to 'sat'
Device: /dev/sdr [SAT], opened
Device: /dev/sdr [SAT], HGST HUS726060ALN610, S/N:NAHYUKHX, WWN:5-000cca-242dba63b, FW:APGNT7J0, 6.00 TB
Device: /dev/sdr [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdr [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdr [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sds, type changed from 'scsi' to 'sat'
Device: /dev/sds [SAT], opened
Device: /dev/sds [SAT], SanDisk SD7SB7S512G1122, S/N:154842401360, WWN:5-001b44-f18e88650, FW:X3540000, 512 GB
Device: /dev/sds [SAT], not found in smartd database.
Device: /dev/sds [SAT], can't monitor Current_Pending_Sector count - no Attribute 197
Device: /dev/sds [SAT], can't monitor Offline_Uncorrectable count - no Attribute 198
Device: /dev/sds [SAT], is SMART capable. Adding to "monitor" list.
Monitoring 1 ATA and 0 SCSI devices
Device: /dev/sds [SAT], opened ATA device
Device: /dev/sds [SAT], opened ATA device
Device: /dev/sds [SAT], opened ATA device
Device: /dev/sds [SAT], opened ATA device
Device: /dev/sds [SAT], opened ATA device
^C
Signal INT - rereading configuration file /etc/smartmontools/smartd.conf (CONTROL-\ quits)
Opened configuration file /etc/smartmontools/smartd.conf
Configuration file /etc/smartmontools/smartd.conf was parsed, found DEVICESCAN, scanning devices
glob(3) found no matches for pattern /dev/hd[a-t]
glob(3) found no matches for pattern /dev/sd[a-c][a-z]
Device: /dev/sda, type changed from 'scsi' to 'sat'
Device: /dev/sda [SAT], opened
Device: /dev/sda [SAT], SanDisk SD7SB7S010T1122, S/N:154727400144, WWN:5-001b44-f120dbed0, FW:X3540000, 1.02 TB
Device: /dev/sda [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sda [SAT], not capable of SMART Health Status check
Device: /dev/sda [SAT], can't monitor Current_Pending_Sector count - no Attribute 197
Device: /dev/sda [SAT], can't monitor Offline_Uncorrectable count - no Attribute 198
Unable to register ATA device /dev/sda [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdb, type changed from 'scsi' to 'sat'
Device: /dev/sdb [SAT], opened
Device: /dev/sdb [SAT], SanDisk SD7SB7S010T1122, S/N:154727400083, WWN:5-001b44-f120dbe93, FW:X3540000, 1.02 TB
Device: /dev/sdb [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdb [SAT], not capable of SMART Health Status check
Device: /dev/sdb [SAT], can't monitor Current_Pending_Sector count - no Attribute 197
Device: /dev/sdb [SAT], can't monitor Offline_Uncorrectable count - no Attribute 198
Unable to register ATA device /dev/sdb [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdc, type changed from 'scsi' to 'sat'
Device: /dev/sdc [SAT], opened
Device: /dev/sdc [SAT], HGST HUS726060ALN610, S/N:NAHYUEUX, WWN:5-000cca-242dba5c9, FW:APGNT7J0, 6.00 TB
Device: /dev/sdc [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdc [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdc [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdd, type changed from 'scsi' to 'sat'
Device: /dev/sdd [SAT], opened
Device: /dev/sdd [SAT], HGST HUS726060ALN610, S/N:NAHYYRKX, WWN:5-000cca-242dbb5dc, FW:APGNT7J0, 6.00 TB
Device: /dev/sdd [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdd [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdd [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sde, type changed from 'scsi' to 'sat'
Device: /dev/sde [SAT], opened
Device: /dev/sde [SAT], HGST HUS726060ALN610, S/N:NAHYSYHX, WWN:5-000cca-242dba02d, FW:APGNT7J0, 6.00 TB
Device: /dev/sde [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sde [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sde [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdf, type changed from 'scsi' to 'sat'
Device: /dev/sdf [SAT], opened
Device: /dev/sdf [SAT], HGST HUS726060ALN610, S/N:NAHYUDTX, WWN:5-000cca-242dba5a9, FW:APGNT7J0, 6.00 TB
Device: /dev/sdf [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdf [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdf [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdg, type changed from 'scsi' to 'sat'
Device: /dev/sdg [SAT], opened
Device: /dev/sdg [SAT], HGST HUS726060ALN610, S/N:NCG2A1VJ, WWN:5-000cca-24dc10e81, FW:APGNT7J0, 6.00 TB
Device: /dev/sdg [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdg [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdg [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdh, type changed from 'scsi' to 'sat'
Device: /dev/sdh [SAT], opened
Device: /dev/sdh [SAT], HGST HUS726060ALN610, S/N:NAHYUH6X, WWN:5-000cca-242dba5f4, FW:APGNT7J0, 6.00 TB
Device: /dev/sdh [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdh [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdh [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdi, type changed from 'scsi' to 'sat'
Device: /dev/sdi [SAT], opened
Device: /dev/sdi [SAT], HGST HUS726060ALN610, S/N:NAHYUM1X, WWN:5-000cca-242dba66b, FW:APGNT7J0, 6.00 TB
Device: /dev/sdi [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdi [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdi [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdj, type changed from 'scsi' to 'sat'
Device: /dev/sdj [SAT], opened
Device: /dev/sdj [SAT], HGST HUS726060ALN610, S/N:NCGJU9ML, WWN:5-000cca-24dc7a4f3, FW:APGNT7J0, 6.00 TB
Device: /dev/sdj [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdj [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdj [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdk, type changed from 'scsi' to 'sat'
Device: /dev/sdk [SAT], opened
Device: /dev/sdk [SAT], HGST HUS726060ALN610, S/N:NAHYUEJX, WWN:5-000cca-242dba5c0, FW:APGNT7J0, 6.00 TB
Device: /dev/sdk [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdk [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdk [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdl, type changed from 'scsi' to 'sat'
Device: /dev/sdl [SAT], opened
Device: /dev/sdl [SAT], HGST HUS726060ALN610, S/N:NAHYUJXX, WWN:5-000cca-242dba629, FW:APGNT7J0, 6.00 TB
Device: /dev/sdl [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdl [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdl [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdm, type changed from 'scsi' to 'sat'
Device: /dev/sdm [SAT], opened
Device: /dev/sdm [SAT], HGST HUS726060ALN610, S/N:NAHYUNLX, WWN:5-000cca-242dba69b, FW:APGNT7J0, 6.00 TB
Device: /dev/sdm [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdm [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdm [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdn, type changed from 'scsi' to 'sat'
Device: /dev/sdn [SAT], opened
Device: /dev/sdn [SAT], HGST HUS726060ALN610, S/N:NAHYUHKX, WWN:5-000cca-242dba5ff, FW:APGNT7J0, 6.00 TB
Device: /dev/sdn [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdn [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdn [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdo, type changed from 'scsi' to 'sat'
Device: /dev/sdo [SAT], opened
Device: /dev/sdo [SAT], HGST HUS726060ALN610, S/N:NAHXYAVX, WWN:5-000cca-242db4012, FW:APGNT7J0, 6.00 TB
Device: /dev/sdo [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdo [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdo [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdp, type changed from 'scsi' to 'sat'
Device: /dev/sdp [SAT], opened
Device: /dev/sdp [SAT], HGST HUS726060ALN610, S/N:NAHYUJ3X, WWN:5-000cca-242dba610, FW:APGNT7J0, 6.00 TB
Device: /dev/sdp [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdp [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdp [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdq, type changed from 'scsi' to 'sat'
Device: /dev/sdq [SAT], opened
Device: /dev/sdq [SAT], HGST HUS726060ALN610, S/N:NAHYUMYX, WWN:5-000cca-242dba687, FW:APGNT7J0, 6.00 TB
Device: /dev/sdq [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdq [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdq [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sdr, type changed from 'scsi' to 'sat'
Device: /dev/sdr [SAT], opened
Device: /dev/sdr [SAT], HGST HUS726060ALN610, S/N:NAHYUKHX, WWN:5-000cca-242dba63b, FW:APGNT7J0, 6.00 TB
Device: /dev/sdr [SAT], not found in smartd database.
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
Device: /dev/sdr [SAT], not capable of SMART Health Status check
Unable to register ATA device /dev/sdr [SAT] at line 23 of file /etc/smartmontools/smartd.conf
Device: /dev/sds, type changed from 'scsi' to 'sat'
Device: /dev/sds [SAT], opened
Device: /dev/sds [SAT], SanDisk SD7SB7S512G1122, S/N:154842401360, WWN:5-001b44-f18e88650, FW:X3540000, 512 GB
Device: /dev/sds [SAT], not found in smartd database.
Device: /dev/sds [SAT], can't monitor Current_Pending_Sector count - no Attribute 197
Device: /dev/sds [SAT], can't monitor Offline_Uncorrectable count - no Attribute 198
Device: /dev/sds [SAT], is SMART capable. Adding to "monitor" list.
Monitoring 1 ATA and 0 SCSI devices
Device: /dev/sds [SAT], opened ATA device
^Z
[1]+ Stopped smartd -d -i 10
[root@370fb07a328b /]#