Re: HD dying?
[email protected] Thu, 6 Apr 2017 10:29:17 -0400
| Newsgroups | gmane.linux.utilities.smartmontools |
|---|---|
| Message-ID | <[email protected]> |
I'll second "Carlos E. R."'s verdict. I see nothing wrong either. However, that does not guarantee there isn't something wrong. Somewhere I read a study that said SMART only predicts about 60% of hard drive failures. The other 40% give no warning. Backups are always a good idea. They protect not only against hard drive failures, but also accidental or malicious data loss. Now have you tested those backups? I remember when I was free-lance going to a brand new client (first visit). They needed me to do a restore. OK, got their backup media (it was back in the zip disk days). Every disk was write-protected, and blank. Needless to say, that day didn't go well. > Hello, > First of all, I *have* been backing up my data. > I'm going to post LOTS of details here, fell free to skim. > > My problem is that once upon a time my drived failed < 6 months after I > bought my laptop. Sending it to a professional did not help, nor did > replacing the PCB, it was dead. > The symptoms leading up to the event was a sudden freeze of the OS. I was > not too bright about Linux at the time, so I thought that perhaps X froze. > Now I'm getting the identical thing, a sudden freeze. I can ping the > kernel, I cannot restore the frame buffer, sync, or umount the > file systems. My syslog metalog records no messages during this period, > it is set to sync the dmesg messages. I cannot ssh, but I can uses sysreq > to reboot. I'm using OpenRC. > > This has happened twice or three times. > I just ran a self test and it says PASSED, I'm not seeing anything that > stands out. > > smartmontools-6.4 > Gentoo Linux 4.9.x > > Below is my S.M.A.R.T. data. BTW: it is unwrapped. > What do you think? > Thanks, David > > > === START OF INFORMATION SECTION === > Model Family: Western Digital Blue Mobile > Device Model: WDC WD7500BPVX-22JC3T0 > Serial Number: WD-WXC1A14E1823 > LU WWN Device Id: 5 0014ee 209f3d675 > Firmware Version: 01.01A01 > User Capacity: 750,156,374,016 bytes [750 GB] > Sector Sizes: 512 bytes logical, 4096 bytes physical > Rotation Rate: 5400 rpm > Device is: In smartctl database [for details use: -P show] > ATA Version is: ACS-2 (minor revision not indicated) > SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) > Local Time is: Tue Apr 4 14:47:54 2017 UTC > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x00) Offline data collection activity > was never started. > Auto Offline Data Collection: Disabled. > Self-test execution status: ( 0) The previous self-test routine > completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: (13920) seconds. > Offline data collection > capabilities: (0x7b) SMART execute Offline immediate. > Auto Offline data collection on/off support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 157) minutes. > Conveyance self-test routine > recommended polling time: ( 5) minutes. > SCT capabilities: (0x7035) SCT Status supported. > SCT Feature Control supported. > SCT Data Table supported. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED > WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always > - 0 > 3 Spin_Up_Time 0x0027 196 179 021 Pre-fail Always > - 1166 > 4 Start_Stop_Count 0x0032 058 058 000 Old_age Always > - 42367 > 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always > - 0 > 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always > - 0 > 9 Power_On_Hours 0x0032 082 082 000 Old_age Always > - 13532 > 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always > - 0 > 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always > - 0 > 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always > - 1695 > 191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always > - 124 > 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always > - 158 > 193 Load_Cycle_Count 0x0032 183 183 000 Old_age Always > - 51774 > 194 Temperature_Celsius 0x0022 107 091 000 Old_age Always > - 40 > 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always > - 0 > 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always > - 0 > 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline > - 0 > 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always > - 0 > 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline > - 0 > > SMART Error Log Version: 1 > No Errors Logged > > SMART Self-test log structure revision number 1 > Num Test_Description Status Remaining > LifeTime(hours) LBA_of_first_error > # 1 Extended offline Completed without error 00% 13529 > - > # 2 Extended offline Completed without error 00% 12288 > - > # 3 Extended offline Completed without error 00% 9247 > - > # 4 Extended offline Completed without error 00% 7609 > - > # 5 Extended offline Completed without error 00% 5469 > - > # 6 Short offline Completed without error 00% 0 > - > # 7 Short offline Completed without error 00% 0 > - > > SMART Selective self-test log data structure revision number 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute > delay. > > > ------------------------------------------------------------------------------ > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Smartmontools-support mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/smartmontools-support > ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot