Trap in DocExaminer after installing/configuring IP/TCP
"Josh Dersch" <[email protected]> Wed, 25 May 2005 21:31:37 -0700
| Newsgroups | gmane.lisp.org.slug |
|---|---|
| Message-ID | <01b601c561ab$cedf26c0$c801a8c0@tor> |
This is a multi-part message in MIME format.
------=_NextPart_000_01B3_01C56171.21E0B360
Content-Type: text/plain;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Thought it'd be nice to get my XL1201 on my local network seeing as I've =
had it for a few months and still haven't gotten around to doing it yet. =
I've run into a snag that I can't quite figure out, any help would be =
appreciated
I've followed the instructions provided in the documentation =
("Installing IP/TCP" If I recall correctly) and everything went smoothly =
up to the point where I Load the IP-TCP system and Enable the Internet =
network; after these commands are issued I get the following Trap in =
Document Examiner without fail whenever I try to view documentation:
"Trap: The word #<DTP-PACKED-INSTRUCTION-70 37776154237> was read from =
location 21013437506 (in *SAGE-COMPLETION-AREA*).
The following specials have been rebound; use :Show Standard Value =
Warnings for details:
CP:*COMMAND-TABLE*"
(note that the addresses involve vary every time)
Nothing else seems to be affected as far as I can tell so far, just =
Document Examiner.
Document Examiner works fine after rebooting with a world without IP-TCP =
loaded. The error message is perhaps a bit on the vague side, so I'm at =
a loss -- any ideas about what the problem is?
Thanks in advance,
Josh
------=_NextPart_000_01B3_01C56171.21E0B360
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=3DContent-Type content=3D"text/html; =
charset=3Diso-8859-1">
<META content=3D"MSHTML 6.00.2900.2627" name=3DGENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=3D#ffffff>
<DIV><FONT face=3DArial size=3D2>Thought it'd be nice to get my XL1201 =
on my local=20
network seeing as I've had it for a few months and still haven't gotten =
around=20
to doing it yet. I've run into a snag that I can't quite figure =
out, any=20
help would be appreciated</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>I've followed the instructions provided =
in the=20
documentation ("Installing IP/TCP" If I recall correctly) and everything =
went=20
smoothly up to the point where I Load the IP-TCP system and Enable the =
Internet=20
network; after these commands are issued I get the following Trap =
in=20
Document Examiner without fail whenever I try to view=20
documentation:</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>"Trap: The word =
#<DTP-PACKED-INSTRUCTION-70=20
37776154237> was read from location 21013437506 (in=20
*SAGE-COMPLETION-AREA*).</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>The following specials have been =
rebound; use :Show=20
Standard Value Warnings for details:</FONT></DIV>
<DIV><FONT face=3DArial size=3D2> CP:*COMMAND-TABLE*"</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>(note that the addresses involve vary =
every=20
time)</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Nothing else seems to be affected as =
far as I can=20
tell so far, just Document Examiner.</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Document Examiner works fine after=20
rebooting with a world without IP-TCP loaded. The error =
message is=20
perhaps a bit on the vague side, so I'm at a loss -- any ideas about =
what the=20
problem is?</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2>Thanks in advance,</FONT></DIV>
<DIV><FONT face=3DArial size=3D2>Josh</FONT></DIV></BODY></HTML>
------=_NextPart_000_01B3_01C56171.21E0B360--