Re: is it possbile to disable smtp, pop3 or imap service for per user?
Carlos García Gómez <[email protected]> Thu, 14 Jul 2011 09:28:47 +0200
| Newsgroups | gmane.mail.qmail.ldap |
|---|---|
| Message-ID | <[email protected]> |
Hi, In qmail-ldap when you disable some account you put ldap attribute accountStatus to noaccess. It disables qmail-pop3 and qmail-imap(s) in account user. Look at below of this mail. Regards --------------------------------------------------------------------- Sistemas de Información y Comunicaciones Fundación Integra. http://www.f-integra.org Teléfono: +34 968 355161 Fax: +34 968 355131 Correo: [email protected] ---------------------------------------------------------------------- Este mensaje y los posibles documentos adjuntos al mismo son confidenciales y dirigidos exclusivamente a los destinatarios de los mismos. Si por un error de transmisión, o equivocación en la dirección de envío, usted ha recibido este mensaje y no es el destinatario de la información, por favor, notifíqueselo al remitente y borre este mensaje, sin usar, informar, distribuir, imprimir, copiar o difundir el mensaje, total o parcialmente, por ningún medio. Gracias. From: Dika Ye Sent: Thursday, July 14, 2011 3:49 AM To: [email protected] Subject: is it possbile to disable smtp, pop3 or imap service for per user? Dear all, is it possbile to disable smtp, pop3 or imap service for per user? Best wishes, Dika.Ye ------------------------------------------------------------------------------------ NTT Com Asia Network Systems (Guangzhou) Company Limited. Tel: (86)-20-8113 0687 Fax: (86)-20-8135 0322 Mobile: (86)-135 3371 0342 Email: [email protected] www.ntt.com.hk #################################################################################################################### From: Carlos García Gómez Sent: Monday, May 04, 2009 12:17 PM To: [email protected] Subject: Qmail-ldap - qmail-imap courier-imap-Version.3.0.8 Hello, I´m using qmail-ldap-couierImap like mix mail solution. Qmail-send, qmail-smtp, qmail-pop3, qmail-pop3-ssl and qmail-qmqpd in QMAIL Courier-authlib, Courier-imap and courier-imap-ssl in COURIER ( versions courier-imap-4.1.3 and courier-authlib-0.59.3 ) In qmail-ldap when you disable some account you put ldap attribute accountStatus to noaccess. It disables qmail-pop3 and qmail-imap(s) in account user. I have always wanted to remove courier-imap from my scenary and use qmail-imap but I could not do it becasue I must be able to disable independently pop3 and imap in some account. I have touch qmail-ldap code in order to add some level of account status ==> noimap and nopop3. So... qmail-ldap.h /* the same values as ints */ #define STATUS_DELETE 3 #define STATUS_BOUNCE 2 #define STATUS_NOACCESS 1 #define STATUS_NOIMAP 4 #define STATUS_NOPOP3 5 #define STATUS_OK 0 #define STATUS_UNDEF -1 #define ISACTIVE_BOUNCE "disabled" #define ISACTIVE_DELETE "deleted" #define ISACTIVE_NOACCESS "noaccess" #define ISACTIVE_NOIMAP "noimap" #define ISACTIVE_NOPOP3 "nopop3" #define ISACTIVE_ACTIVE "active" qldap.c } else if (r == OK) { if (!case_diffs(ldap_attr.s, ISACTIVE_BOUNCE)) *status = STATUS_BOUNCE; else if (!case_diffs(ldap_attr.s, ISACTIVE_DELETE)) *status = STATUS_DELETE; else if (!case_diffs(ldap_attr.s, ISACTIVE_NOACCESS)) *status = STATUS_NOACCESS; else if (!case_diffs(ldap_attr.s, ISACTIVE_NOIMAP)) *status = STATUS_NOIMAP; else if (!case_diffs(ldap_attr.s, ISACTIVE_NOPOP3)) *status = STATUS_NOPOP3; else *status = STATUS_OK; /* default to OK */ /* perhaps we should spill out a warning for unknown settings */ return OK; qmail-ldaplookup.c switch (status) { case STATUS_BOUNCE: output(subfdout, "%s: %s\n", LDAP_ISACTIVE, ISACTIVE_BOUNCE); break; case STATUS_NOACCESS: output(subfdout, "%s: %s\n", LDAP_ISACTIVE, ISACTIVE_NOACCESS); break; case STATUS_NOIMAP: output(subfdout, "%s: %s\n", LDAP_ISACTIVE, ISACTIVE_NOIMAP); break; case STATUS_NOPOP3: output(subfdout, "%s: %s\n", LDAP_ISACTIVE, ISACTIVE_NOPOP3); break; case STATUS_OK: output(subfdout, "%s: %s\n", LDAP_ISACTIVE, ISACTIVE_ACTIVE); break; and in checkpassword.c if ( status == STATUS_BOUNCE || status == STATUS_DELETE || status == STATUS_NOACCESS ) { qldap_free(q); return ACC_DISABLED; }else if ( status == STATUS_NOPOP3 ) { if ( strcmp(env_get("TCPLOCALPORT"),"110") == 0 || strcmp(env_get("TCPLOCALPORT"),"995") == 0 ) { fprintf(stderr,"User %s is not allowed to log on PORT %s\n",login->s,env_get("TCPLOCALPORT")); qldap_free(q); return ACC_DISABLED; } }else if ( status == STATUS_NOIMAP ) { if ( strcmp(env_get("TCPLOCALPORT"),"143") == 0 || strcmp(env_get("TCPLOCALPORT"),"993") == 0 ) { fprintf(stderr,"User %s is not allowed to log on PORT %s\n",login->s,env_get("TCPLOCALPORT")); qldap_free(q); return ACC_DISABLED; } } And it seems that`s is all right!!! Only one thing: If I want to use qmail-imap I have to use courier-login from courier-imap-VERSION-3.0.8. My question is: Is it safe? What`s your opinion? (use courier-imap-VERSION-3.0.8) Any bugs known in courier-imap-VERSION-3.0.8? Regards --------------------------------------------------------------------- Carlos García Gómez Sistemas de Información y Comunicaciones Fundación Integra. http://www.f-integra.org Teléfono: +34 968 355161 Fax: +34 968 355131 Correo: [email protected] ---------------------------------------------------------------------- Este mensaje y los posibles documentos adjuntos al mismo son confidenciales y dirigidos exclusivamente a los destinatarios de los mismos. Si por un error de transmisión, o equivocación en la dirección de envío, usted ha recibido este mensaje y no es el destinatario de la información, por favor, notifíqueselo al remitente y borre este mensaje, sin usar, informar, distribuir, imprimir, copiar o difundir el mensaje, total o parcialmente, por ningún medio. Gracias.