sendmail 8.13.1 available
Claus Assmann <[email protected]> Sat, 31 Jul 2004 10:35:53 -0700 (PDT)
| Newsgroups | gmane.mail.sendmail.announce |
|---|---|
| Message-ID | <[email protected]> |
-----BEGIN PGP SIGNED MESSAGE----- Sendmail, Inc., and the Sendmail Consortium announce the availability of sendmail 8.13.1. It contains fixes for problems that have been found after release of 8.13.0 as well as some portability enhancements. For a full list of changes see the release notes down below. Please send bug reports to [email protected] and general feedback to [email protected]. Please send security reports to [email protected] using PGP encryption. The version can be found at ftp://ftp.sendmail.org/pub/sendmail/sendmail.8.13.1.tar.gz ftp://ftp.sendmail.org/pub/sendmail/sendmail.8.13.1.tar.gz.sig ftp://ftp.sendmail.org/pub/sendmail/sendmail.8.13.1.tar.Z ftp://ftp.sendmail.org/pub/sendmail/sendmail.8.13.1.tar.Z.sig MD5 signatures: 5407db289086261d7e7a09920d2ea14e sendmail.8.13.1.tar.gz 0988704f02b7cca5e4c75202b1cbea3c sendmail.8.13.1.tar.gz.sig 30a3113937b09a71f6bc8aeb46557dbd sendmail.8.13.1.tar.Z cc97251edfead115bbd43876320215ea sendmail.8.13.1.tar.Z.sig You either need the first two files or the third and fourth, i.e., the gzip'ed version or the compressed version and the corresponding sig file. The PGP signature was created using the Sendmail Signing Key/2004, available on the web site (http://www.sendmail.org/) or on the public key servers. Since sendmail 8.11 and later includes hooks to cryptography, the following information from OpenSSL applies to sendmail as well. PLEASE REMEMBER THAT EXPORT/IMPORT AND/OR USE OF STRONG CRYPTOGRAPHY SOFTWARE, PROVIDING CRYPTOGRAPHY HOOKS OR EVEN JUST COMMUNICATING TECHNICAL DETAILS ABOUT CRYPTOGRAPHY SOFTWARE IS ILLEGAL IN SOME PARTS OF THE WORLD. SO, WHEN YOU IMPORT THIS PACKAGE TO YOUR COUNTRY, RE-DISTRIBUTE IT FROM THERE OR EVEN JUST EMAIL TECHNICAL SUGGESTIONS OR EVEN SOURCE PATCHES TO THE AUTHOR OR OTHER PEOPLE YOU ARE STRONGLY ADVISED TO PAY CLOSE ATTENTION TO ANY EXPORT/IMPORT AND/OR USE LAWS WHICH APPLY TO YOU. THE AUTHORS ARE NOT LIABLE FOR ANY VIOLATIONS YOU MAKE HERE. SO BE CAREFUL, IT IS YOUR RESPONSIBILITY. SENDMAIL RELEASE NOTES $Id: RELEASE_NOTES,v 8.1679 2004/07/30 18:03:07 ca Exp $ This listing shows the version of the sendmail binary, the version of the sendmail configuration files, the date of release, and a summary of the changes in that release. 8.13.1/8.13.1 2004/07/30 Using the default AliasFile ldap: specification would cause the objectClasses of the LDAP response to be included in the alias expansion. Problem noted by Brenden Conte of Rensselaer Polytechnic Institute. Fix support for a fallback smart host for system where DNS is (partially) available. From John Beck of Sun Microsystems. Fix SuperSafe=PostMilter behavior when a milter replaces a body but the data file is not yet stored on disk because it is smaller than the size of the memory buffer. Problem noted by David Russell. Fix certificate revocation list support; if a CRL was specified but the other side presented a cert that was signed by a different (trusted) CA than the one which issued the CRL, verification would always fail. Problem noted by Al Smith. Run mailer programs as the RunAsUser when RunAsUser is set and the F=S mailer flag is set without a U= mailer equate. Problem noted by John Gardiner Myers of Proofpoint. ${nbadrcpts} was off by one if BadRcptThrottle is zero. Patch from Sung-hoon Choi of DreamWiz Inc. CONFIG: Emit a warning if FEATURE(`access_db') is used after FEATURE(`greet_pause') because then the latter will not use the access map. Note: if no default value is given for FEATURE(`greet_pause') then it issues an error if FEATURE(`access_db') is not specified before it. Problem noted by Alexander Dalloz of University of Bielefeld. CONFIG: Invoke ruleset Local_greet_pause if FEATURE(`greet_pause') is used to give more flexibility for local changes. Portability: Fix a 64 bit problem in the socket map code. Problem noted by Geoff Adams. NetBSD 2.0F has closefrom(3). Patch from Andrew Brown. NetBSD can use sysctl(3) to get the number of CPUs in a system. Patch from Andrew Brown. Add a README file in doc/op/ to explain potential incompatibilities with various *roff related tools. Problem tracked down by Per Hedeland. New Files: doc/op/README -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.5 (OpenBSD) iQCVAwUBQQvFM88etQMiMnoBAQFCigQAgiTO2D6mjROu58leh0YHRvNPUjqzN14L uZGR64HnMcMfbo5VR33tlVwyxr1MQLiul4txuGkYXr9CdVRVg5txX/rwTV8Z7KdB G+8i/Xa5YMyifUI5U4q4BXy+sLhiiFJEBflqnl7efJq90oQZLz/HmgMBYsGkpqOU ReBCZSdwaXw= =pdaJ -----END PGP SIGNATURE-----