| Newsgroups |
gmane.mail.vpopmail |
| Message-ID |
<002501cb52de$a928ecc0$fb7ac640$@com> |
Hi Remo:
Actually we do use Bill Shupp's toaster and find his instructions very easy to follow. Unfortunately it's been over three years since he's updated his toaster and, I far as I can tell, there are NO instructions for adding an SMTP-AUTH only submission port on 587 in addition to the main smtp port on 25.
If you found some special instructions please let me know.
Jeff Koch
-----Original Message-----
From: Remo Mattei [mailto:[email protected]]
Sent: Sunday, September 12, 2010 9:59 AM
To: [email protected]
Cc: [email protected]
Subject: Re: [vchkpw] Re: submission port 587
Check bill shupp site you can find anything you need
Inviato da iPhone
Il giorno Sep 11, 2010, alle ore 23:25, Eric Shubert <[email protected]> ha scritto:
> The 'stock' qmail-toaster (http://qmailtoaster.com) contains this.
>
> The only difference between the smtp/run and submission/run files is that the submission/run file contains the -H flag for tcpserver, and:
> export REQUIRE_AUTH=1
> which tells the authentication patch to always authenticate.
>
> qmail-toaster includes the following patch:
> Jean-Paul van de Plasse - REQUIRE_AUTH Patch
> which is what checks the REQUIRE_AUTH environment variable.
> You'll need to do some searching to find that patch, or grab it from the qmail-toaster srpm package.
>
> HTH.
>
> --
> -Eric 'shubes'
>
> [email protected] wrote:
>> Hi Thiago – thanks – I’ll give this a try. Jeff
>> *From:* Thiago Bujnowski - Ticonnect Solutions [mailto:[email protected]]
>> *Sent:* Saturday, September 11, 2010 9:43 PM
>> *To:* [email protected]
>> *Subject:* Re: [vchkpw] submission port 587
>> You can just create another directory at /var/qmail/supervise with a run file running on port 587 and using a different tcp.smtp file.
>> I wanted separeted processes for internal and external incoming mail at my MX server.
>> Here is how I did it:
>> - I followed a regular instalation as described in lifewithqmail + smtpauth.
>> - Instaled Vpopmail
>> - Applied the chkuser patch
>> - Instead of replacing qmail-smtp at /var/qmail/bin I renamed the patched file to qmail-mx and copied into it.
>> - Created a /var/qmail/supervise/qmail-mx folder and modified the run file to use qmail-mx instead of qmail-smtp binary and tcp.mx.cdb instead of tcp.smtp.cdb, and chaged the listening IP. (You your case, you should modify the listening port to 587)
>> - Created the link at /service
>> - Modified qmailctl adding the qmail-mx process. (Also generating the tcp.mx.cdb file from tcp.mx)
>> It works like a charm for me and I think you could just adapt the overall idea fitting your needs.
>> There is just one inconvenience with this setup. The config files for qmail (rcpthosts and etc..) must be the same for both processes. It would require further modifications on qmail-smtp.c to use diferent config files for each process.
>> Your new CDB file should have no open relays allowing only authenticated mail to pass through.
>> That should do the trick.
>> Does anyone have a better suggestion?
>> Regards,
>> Thiago Bujnowski
>> *From:* Rick Macdougall <mailto:[email protected]>
>> *Sent:* Saturday, September 11, 2010 9:57 PM
>> *To:* [email protected] <mailto:[email protected]>
>> *Subject:* Re: [vchkpw] submission port 587
>> Sorry for the top post, on my IPod.
>> If no one answers before tomorrow, I'll reply when I get on my computer. It's pretty straight forward.
>> Rick
>> On 2010-09-11, at 18:39, <[email protected] <mailto:[email protected]>> wrote:
>> This may be the wrong forum for this but I can’t seem to find any info.
>> Does anyone have information on how to setup a second SMTP process
>> within qmail that listens on port 587 and accepts ONLY authenticated
>> smtp connections? In this scenario port 25 would accept normal smtp
>> (non-relay) and smtp-auth traffic but now could also be filtered to
>> block dynamic IP ranges.
>> Thanks,
>> Jeff Koch
>
>
>
>
>
>
>
!DSPAM:4c8d770232711197767315!