Re: Backlight [etc.]

this will be definitely helpful!

muchas gracias,


Fabio

--- In [email protected], Alvaro Correa <correalicio@...> wrote:
>
> Hi, friends, here you have:
> 
> 
> 
> *Web page at Digi-Key*
> 
> http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=289-1032-ND
> (page with replacement EL inverter)
> 
> 
> 
> *Digi-Key Part Number:*   *289-1032-ND*
> 
> 
> 
> Manufacturer: JKL Components
> Corp.<http://digikey.com/Suppliers/us/JKL-Components.page?lang=EN>
> 
> Manufacturer Part Number: *NDL-205*
> 
> 
> 
> This is the inverter I've installed last month in my unit. Just some
> additional comments:
> 
> The pins will line up differently on the new part, I used the output pin in
> the original output hole as a marker and drilled new holes through the board
> for the 3 remaining pins (be sure the new holes you are going to drill will
> not short to any traces when you drill through the board).
> 
> Drill two extra holes through the board (just to each side of inverter) to
> allow a plastic zip tie to go through bottom of hole around the top of
> inverter and back down through second hole to zip tight under the bottom of
> inverter board to hold inverter in place against the board, you may use two
> plastic zip ties if needed.
> 
> Hard wire (jump) the remaining pins to the proper location
> 
> IN = 5V DC
> 
> G  = Ground
> 
> OUT = AC output for EL backlight panel
> 
> NC = No Connection
> 
> 
> 
> Good Luck SKY!!!
> 
> 
> Saludos, Alvaro.-
> 
> 
> 
> 
> On Thu, Aug 19, 2010 at 2:02 PM, Antoine Deschênes <antdes45@...>wrote:
> 
> > Cold solder joints inside the inverter, which is filled with epoxy. (Can't
> > be fixed.)
> >
> > There's a JKL inverter that has the same specs, but a different form
> > factor. It's possible to use it. I can't tell you the model number right
> > now, but it's somewhere on kfuenf.org .
> >
> >
> > Antoine
> >
> > -original message-
> > Subject: [k5synth] Re: Backlight [etc.]
> > From: "somethingkillingyou" <somethingkillingyou@...>
> > Date: 19/08/2010 12:48
> >
> > wtf?! now it is working again...
> >
> > I switched on my K5 and left it on for a while (~1 hour) and everything was
> > ok...
> >
> > then I switched it off and on a few times, the backlight was ok...
> >
> > it seems the inverter is not dead, it's just unreliable...
> >
> > anyway... what's the replacement for this 'nichia' white inverter?
> >
> >
> >
> > --- In [email protected], "somethingkillingyou"
> > <somethingkillingyou@> wrote:
> > >
> > > new backlight bought and installed; the display was working fine, then
> > after a few seconds (less than a minute for sure), backlight gone again...
> > >
> >
> >
> >
> > ------------------------------------
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> > ------------------------------------
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
>




------------------------------------