Hello Scott,
our version: 5.1(3)N1(1a) (really old :-))
here the output of sh int vlan 100 coun snmp
--------------------------------------------------------------------------------
Port InOctets InUcastPkts
--------------------------------------------------------------------------------
Vlan100 24102320537442 36678696592
--------------------------------------------------------------------------------
Port InMcastPkts InBcastPkts
--------------------------------------------------------------------------------
Vlan100 0 0
--------------------------------------------------------------------------------
Port OutOctets OutUcastPkts
--------------------------------------------------------------------------------
Vlan100 34166144843228 44159646841
--------------------------------------------------------------------------------
Port OutMcastPkts OutBcastPkts
--------------------------------------------------------------------------------
Vlan100 0 0
It is incrementing.
Here the other output:
sh interface vlan 100
Vlan100 is up, line protocol is up
Hardware is EtherSVI, address is 547f.zzzz.zzzz
Description: SAP-Dialog
Internet Address is 172.999.999.999/24
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
.
sh int ethernet 1/6
Ethernet1/6 is up
Hardware: 1000/10000 Ethernet, address: 547f.ee63.664d (bia 547f.ee63.664d)
Description: Fex01-II
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is fex-fabric
full-duplex, 10 Gb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 238week(s) 4day(s)
Last clearing of "show interface" counters 71w5d
30 seconds input rate 33101928 bits/sec, 7320 packets/sec
30 seconds output rate 60070640 bits/sec, 9998 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 30.63 Mbps, 6.24 Kpps; output rate 56.76 Mbps, 10.61 Kpps
RX
177554735898 unicast packets 16220010 multicast packets 494448 broadcast packets
177571450356 input packets 92831179974458 bytes
37017840974 jumbo packets 0 storm suppression bytes
0 runts 0 giants 0 CRC 0 no buffer
0 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
262460154587 unicast packets 126330100 multicast packets 6258134 broadcast packets
262592742821 output packets 211724177600413 bytes
101020844014 jumbo packets
0 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble 0 output discard
0 Tx pause
0 interface resets
Klaus
-----Ursprüngliche Nachricht-----
Von: Scott Voll [mailto:[email protected]]
Gesendet: Freitag, 16. August 2013 18:26
An: Support requests/questions about cacti
Betreff: Re: [cacti-user] Layer 3 interface on cisco Nexus 5548
Bug ID CSCti07554. upgrade to 6.0.2N1(1) or better.
Also, use "show inter vlan XXX counter snmp" to see counters increment.
Scott
On Fri, Aug 16, 2013 at 7:58 AM, Scott Voll <[email protected]> wrote:
> What version are you on? all my snmp walks show 0 for ifin/out unicast
> packets running version 5.2(1)N1(3)
>
> in my version sh interface shows:
>
> 5548A# sh inter vlan 100
> Vlan100 is up, line protocol is up
> Hardware is EtherSVI, address is 547f.yyyy.yyyy
> Description: Core Network
> Internet Address is 10.x.x.x/24
> MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
>
> 5548A#
> 5548A#
> 5548A# sh inter e1/9
> Ethernet1/9 is up
> Dedicated Interface
> Belongs to Po109
> Hardware: 1000/10000 Ethernet, address: 547f.zzzz.zzzz
> Description: Connection to 2248 #1
> MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation ARPA
> Port mode is fex-fabric
> full-duplex, 10 Gb/s, media type is 10G
> Beacon is turned off
> Input flow-control is off, output flow-control is off
> Rate mode is dedicated
> Switchport monitor is off
> EtherType is 0x8100
> Last link flapped 21week(s) 2day(s)
> Last clearing of "show interface" counters never
> 30 seconds input rate 430344 bits/sec, 78 packets/sec
> 30 seconds output rate 1039024 bits/sec, 473 packets/sec
> Load-Interval #2: 5 minute (300 seconds)
> input rate 610.62 Kbps, 47 pps; output rate 1.50 Mbps, 511 pps
> RX
> 7903308560 unicast packets 4496064 multicast packets 337352
> broadcast packets
> 7908141976 input packets 3908030485102 bytes
> 2090854495 jumbo packets 0 storm suppression bytes
> 0 runts 0 giants 0 CRC 0 no buffer
> 0 input error 0 short frame 0 overrun 0 underrun 0 ignored
> 0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
> 0 input with dribble 0 input discard
> 0 Rx pause
> TX
> 5572083534 unicast packets 182626399 multicast packets 103229128
> broadcast packets
> 5857939061 output packets 2380448231417 bytes
> 1081561337 jumbo packets
> 0 output errors 0 collision 0 deferred 0 late collision
> 0 lost carrier 0 no carrier 0 babble 0 output discard
> 0 Tx pause
> 4 interface resets
>
>
> As you can see there are NO counters on my layer 3 vlan interface(SVI)
> .
> TIA
>
> Scott
>
>
>
>
> On Fri, Aug 16, 2013 at 7:15 AM, <[email protected]> wrote:
>
>> Hello!
>>
>> The N5K without L3-daughter-card is a simple L2 switch.
>> with the daughter-card you see a "propVirtual(53)" interface type when you
>> ran
>> the (standard) 'SNMP - Interface Statistics' query and get data (and
>> graphs).
>>
>> klaus
>>
>> -----Ursprüngliche Nachricht-----
>> Von: Gandalf [mailto:[email protected]]
>> Gesendet: Donnerstag, 15. August 2013 18:46
>> An: Support requests/questions about cacti
>> Betreff: Re: [cacti-user] Layer 3 interface on cisco Nexus 5548
>>
>> So where should Cacti get the data from?
>> In case there's a private Cisco MIB providing the wanted data, there will
>> be
>> a
>> solution with Cacti ...
>>
>> R.
>>
>> On 15.08.2013 18:38, Scott Voll wrote:
>> > All counters are Zero for layer three vlan interfaces.
>> >
>> > Scott
>> >
>> >
>> > On Thu, Aug 15, 2013 at 8:46 AM, Gandalf <[email protected]> wrote:
>> >
>> >> Does an snmpwalk yield results for the VLAN interfaces?
>> >> R,
>> >>
>> >> On 15.08.2013 16:13, Scott Voll wrote:
>> >>> I'm trying to monitor my layer 3 (vlans) with Cacti. it sees the
>> >> interface
>> >>> but I get no data. I can see traffic on the CLI but no graphs in
>> >>> Cacti(just layer 3). Since the 5548 requires a daughter card to get
>> >> layer
>> >>> three, is that why I see no data on my graphs?
>> >>>
>> >>> TIA
>> >>>
>> >>> Scott
>> >>>
>> >>
>>
>> ----------------------------------------------------------------------------
>> --
>> >>> Get 100% visibility into Java/.NET code with AppDynamics Lite!
>> >>> It's a free troubleshooting tool designed for production.
>> >>> Get down to code-level detail for bottlenecks, with <2% overhead.
>> >>> Download for free and get started troubleshooting in minutes.
>> >>>
>> >>
>>
>> http://pubads.g.doubleclick.net/gampad/clk?id=48897031&iu=/4140/ostg.clktrk
>> >>> _______________________________________________
>> >>> cacti-user mailing list
>> >>> [email protected]
>> >>> https://lists.sourceforge.net/lists/listinfo/cacti-user
>> >>>
>> >>
>> >>
>> >>
>>
>> ----------------------------------------------------------------------------
>> --
>> >> Get 100% visibility into Java/.NET code with AppDynamics Lite!
>> >> It's a free troubleshooting tool designed for production.
>> >> Get down to code-level detail for bottlenecks, with <2% overhead.
>> >> Download for free and get started troubleshooting in minutes.
>> >>
>>
>> http://pubads.g.doubleclick.net/gampad/clk?id=48897031&iu=/4140/ostg.clktrk
>> >> _______________________________________________
>> >> cacti-user mailing list
>> >> [email protected]
>> >> https://lists.sourceforge.net/lists/listinfo/cacti-user
>> >>
>> >
>>
>> ----------------------------------------------------------------------------
>> --
>> > Get 100% visibility into Java/.NET code with AppDynamics Lite!
>> > It's a free troubleshooting tool designed for production.
>> > Get down to code-level detail for bottlenecks, with <2% overhead.
>> > Download for free and get started troubleshooting in minutes.
>> >
>>
>> http://pubads.g.doubleclick.net/gampad/clk?id=48897031&iu=/4140/ostg.clktrk
>> > _______________________________________________
>> > cacti-user mailing list
>> > [email protected]
>> > https://lists.sourceforge.net/lists/listinfo/cacti-user
>> >
>>
>>
>> ----------------------------------------------------------------------------
>> --
>> Get 100% visibility into Java/.NET code with AppDynamics Lite!
>> It's a free troubleshooting tool designed for production.
>> Get down to code-level detail for bottlenecks, with <2% overhead.
>> Download for free and get started troubleshooting in minutes.
>>
>> http://pubads.g.doubleclick.net/gampad/clk?id=48897031&iu=/4140/ostg.clktrk
>> _______________________________________________
>> cacti-user mailing list
>> [email protected]
>> https://lists.sourceforge.net/lists/listinfo/cacti-user
>>
>>
>> ------------------------------------------------------------------------------
>>
>> Get 100% visibility into Java/.NET code with AppDynamics Lite!
>> It's a free troubleshooting tool designed for production.
>> Get down to code-level detail for bottlenecks, with <2% overhead.
>> Download for free and get started troubleshooting in minutes.
>>
>> http://pubads.g.doubleclick.net/gampad/clk?id=48897031&iu=/4140/ostg.clktrk
>> _______________________________________________
>> cacti-user mailing list
>> [email protected]
>> https://lists.sourceforge.net/lists/listinfo/cacti-user
>>
>>
>
------------------------------------------------------------------------------
Get 100% visibility into Java/.NET code with AppDynamics Lite!
It's a free troubleshooting tool designed for production.
Get down to code-level detail for bottlenecks, with <2% overhead.
Download for free and get started troubleshooting in minutes.
http://pubads.g.doubleclick.net/gampad/clk?id=48897031&iu=/4140/ostg.clktrk
_______________________________________________
cacti-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/cacti-user
------------------------------------------------------------------------------
Introducing Performance Central, a new site from SourceForge and
AppDynamics. Performance Central is your source for news, insights,
analysis and resources for efficient Application Performance Management.
Visit us today!
http://pubads.g.doubleclick.net/gampad/clk?id=48897511&iu=/4140/ostg.clktrk
lmpx.com only provides a reader for public news (NNTP) servers. It is not
affiliated with the servers or forums shown here and is not responsible for
the content of articles, which is written by their respective authors.