Wireless

Hi,

i've tried to get gpxe with an Atheros wireless card to work. But it won't. I'm using the code from http://git.etherboot.org/?p=people/oremanj/gpxe.git;a=tree;h=refs/heads/wireless;hb=wireless.

Command 'iwstat' shows the current state of the adapter
[Sig] SSID BSSID Ch Crypt/Auth
-------------------------------------------------------------
[ 41] ME 00:1f:3f:17:49:5e 1 WPA2 PSK
[ 3] Hirsch6 00:12:2a:05:73:45 6 WPA2 PSK

Command 'iwlist' show all available SSID
net0: 00:18:e7:2b:05:f2 on PCI00:14.0 (closed)
[Link:down, TX:0 TXE:0 RX:0 RXE:0]
[Link status: Not connected (0x38086001)]
[802.11 not associated, Ch:14 Sig:14/40 dB, Qual:0% Rate:1 Mbps]

After setting SSID and KEY as described at http://etherboot.org/wiki/wirelessboot and run command 'dhcp net0' only an errormessage will appear.
Also setting DEBUG=ath5k,ath5k_phy,pci,wpa shows nothing which gives me a hint where to looking for the problem.

Can anybody give me an advice!?

See below the trace from the gpxe console. GPXE over wired network works perfectly.

With best regards
Peter

Adding PCI device 00:00.0 (1106:3123 mem e0000000 io 0 irq 0)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:01.0 (1106:b091 mem 10100 io 0 irq 0)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:10.0 (1106:3038 mem 0 io d000 irq 11)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:10.1 (1106:3038 mem 0 io d400 irq 10)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:10.2 (1106:3038 mem 0 io d800 irq 5)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:10.3 (1106:3104 mem ea010000 io 0 irq 7)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:11.0 (1106:3177 mem 0 io 0 irq 0)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:11.1 (1106:0571 mem 0 io dc00 irq 255)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:11.5 (1106:3059 mem 0 io e000 irq 5)
...using driver undipci
......probe failed
...no driver found
Adding PCI device 00:14.0 (168c:0013 mem ea000000 io 0 irq 10)
...using driver ath5212
PCI BIOS has not enabled device 00:14.0! Updating PCI command 0006->0007
ath5k: register base at 0xdc1db680 (ea000000)
ath5k: cache line size 32
Atheros AR2414 chip found (MAC: 0x79, PHY: 0x45)
Adding PCI device 01:00.0 (1106:3122 mem e4000000 io 0 irq 11)
...using driver undipci
......probe failed
...no driver found



gPXE 0.9.8+ -- Open Source Boot Firmware -- http://etherboot.org
Features: AoE HTTP iSCSI DNS TFTP bzImage COMBOOT ELF Multiboot PXE PXEXT

gPXE> iwlist
ath5k: txq [0] 0, link 0x0
repeats 10 times
ath5k: txq [0] 0, link 0x0
Networks on net0:

[Sig] SSID                  BSSID              Ch  Crypt/Auth
-------------------------------------------------------------
[ 41] ME                    00:1f:3f:17:49:5e   1  WPA2  PSK
[  3] Hirsch6               00:12:2a:05:73:45   6  WPA2  PSK

ath5k: txq [0] 0, link 0x0
gPXE> iwstat
net0: 00:18:e7:2b:05:f2 on PCI00:14.0 (closed)
  [Link:down, TX:0 TXE:0 RX:0 RXE:0]
  [Link status: Not connected (0x38086001)]
  [802.11 not associated, Ch:14 Sig:14/40 dB, Qual:0% Rate:1 Mbps]
gPXE> set net0/ssid ME
gPXE> set net0/key seecret
gPXE> dhcp net0
ath5k: txq [0] 0, link 0x0
Waiting for link-up on net0...
ath5k: txq [0] 0, link 0x0
repeats 165 times
ath5k: txq [0] 0, link 0x0
 failed: Error 0x371f6003
Could not configure net0: Error 0x371f6003
gPXE> ath5k: txq [0] 0, link 0x0
ath5k: txq [0] 0, link 0x0
ath5k: txq [0] 0, link 0x0
ath5k: txq [0] 0, link 0x0
ath5k: txq [0] 0, link 0x0
repeats endless
------------------------------------------------------------------------------------
XMail.net Communications Center

------------------------------------------------------------------------------
Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day 
trial. Simplify your report design, integration and deployment - and focus on 
what you do best, core application coding. Discover what's new with
Crystal Reports now.  http://p.sf.net/sfu/bobj-july