RE: What do I need to do to get EtherealtodecodeDOCSIS frames ?

Hi,
I already had WinPcap 3.1 installed, therefore, I installed WinPcap
4.0alpha1. I got the same results, no access to the grayed out box
Link-layer header type in the capture options and no decoding of Docsis
frames. I tried the docsis frames with and without the 6 byte MAC
Header.  I think the problem is the grayed out Link-layer Header type
capture option.  Please continue to assist.

Thanks,
Cliff.

-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of ??
Sent: Tuesday, June 27, 2006 7:26 PM
To: Ethereal user support
Subject: Re: [Ethereal-users] What do I need to do to get
EtherealtodecodeDOCSIS frames ?

HI,
    you can get it at http://www.winpcap.org/ ,
     In windows  is called WinPcap.

2006/6/28, Epps, Clifton <[email protected]>:
> Hi,
> No I didn't.  Where do I get a windows version of libcap ?
>
> Thanks,
> Cliff.
>
> -----Original Message-----
> From: [email protected]
> [mailto:[email protected]] On Behalf Of ??
> Sent: Tuesday, June 27, 2006 5:52 PM
> To: Ethereal user support
> Subject: Re: [Ethereal-users] What do I need to do to get Ethereal
> todecodeDOCSIS frames ?
>
> Hi,
>      Did you update your libpcap?You could get the last version 0.9.4
> on the website www.tcpdump.org then install and try again.
>
> 2006/6/28, Epps, Clifton <[email protected]>:
> > Hi,
> > I tried both, however, no luck. The Wireshark user manual suggest
one
> > has to set the Link-Layer Header Type under capture options to
DOCSIS
> > but the option field is always grayed out so I can't use it to
select
> > anything. How do I go about getting access to the capture option
> > link-layer header type field ?
> >
> > Thanks,
> > Cliff.
> >
> > -----Original Message-----
> > From: [email protected]
> > [mailto:[email protected]] On Behalf Of Guy Harris
> > Sent: Friday, June 23, 2006 2:13 PM
> > To: Ethereal user support
> > Subject: Re: [Ethereal-users] What do I need to do to get Ethereal
> > todecode DOCSIS frames ?
> >
> >
> > On Jun 23, 2006, at 9:37 AM, Epps, Clifton wrote:
> >
> > > Hi Ethereal-user Support,
> > >
> > > I'm trying to get Ethereal version 0.10.14 to Decode Docsis frames
> > > but I can't get it to work.  The MAC header and MAC management
> > > header looks good.  I tried it with all protocols enabled and with
> > > only the DOCSIS blocks checked under enabled protocols.  What do I
> > > need to do to get Ethereal to decode DOCSIS frames ?
> > I think there might have been a bug in 0.10.14 that prevented the
> > "Decode all frames as DOCSIS" option from working.  Try upgrading to
> > Ethereal 0.99.0 - or to Wireshark 0.99.1pre1 from www.wireshark.org.
> > _______________________________________________
> > Ethereal-users mailing list
> > [email protected]
> > http://www.ethereal.com/mailman/listinfo/ethereal-users
> > _______________________________________________
> > Ethereal-users mailing list
> > [email protected]
> > http://www.ethereal.com/mailman/listinfo/ethereal-users
> >
> _______________________________________________
> Ethereal-users mailing list
> [email protected]
> http://www.ethereal.com/mailman/listinfo/ethereal-users
> _______________________________________________
> Ethereal-users mailing list
> [email protected]
> http://www.ethereal.com/mailman/listinfo/ethereal-users
>
_______________________________________________
Ethereal-users mailing list
[email protected]
http://www.ethereal.com/mailman/listinfo/ethereal-users