-pre6 fails on my test box, RCH problem

-----BEGIN PGP SIGNED MESSAGE-----

  Ok, at least two bugs somewhere in here.  I am trying to use the
- -pre6 (maybe at the FTP site by now, check in the development section)
and find that "make oldmod" fails (if it's obsolete then it should
never try to run...).  Looking closer the failure it dies on is the
compiler loosing it, the problems are WAY earlier.

  The second problem is that somone spaced a makefile vs. SHELL
variable and needs to put some {} in the right place, as we keep
getting "RCH" rather then say i386 or z800 as it should be.

  Next looking at the output more I find that the patching system
fails to error out as it should when this starts happening:

...
patching file net/ipv4/af_inet.c
Hunk #1 succeeded at 1179 (offset 160 lines).
patching file net/ipsec/Makefile.ver
grep: /usr/src/linux/arch/RCH/defconfig: No such file or directory
+ cp -a /usr/src/linux/arch/RCH/defconfig /usr/src/linux/arch/RCH/defconfig.orig
cp: cannot stat `/usr/src/linux/arch/RCH/defconfig': No such file or directory
+ chmod u+w /usr/src/linux/arch/RCH/defconfig
...

  Is is an example of "RCH" failure output.

...
make[1]: Leaving directory `/usr/src/freeswan-2.00-pre6/testing'
make -C linux/net/ipsec ARCH=RCH KLIPSMODULE=true TOPDIR=/usr/src/linux -f /usr/
src/freeswan-2.00-pre6/linux/net/ipsec/defconfig -f Makefile MODULE_DEF_INCLUDE=
/usr/src/freeswan-2.00-pre6/packaging/linus/config-all.h ipsec.o
Makefile:254: arch/RCH/Makefile: No such file or directory
make[1]: *** No rule to make target `arch/RCH/Makefile'.  Stop.
Makefile:254: arch/RCH/Makefile: No such file or directory
make[1]: *** No rule to make target `arch/RCH/Makefile'.  Stop.
make[1]: execvp: /usr/src/linux/scripts/pathdown.sh: Permission denied
make[1]: Entering directory `/usr/src/freeswan-2.00-pre6/linux/net/ipsec'
cc  -DIPCOMP_PREFIX -include /usr/src/freeswan-2.00-pre6/packaging/linus/config-
all.h -I../../include -I/usr/src/linux/include  -I../../lib/zlib  -Wall -DARCH=R
CH  -DMODVERSIONS -include /usr/src/linux/include/linux/modversions.h     -DKBUI
LD_BASENAME=ipsec_init  -c -o ipsec_init.o ipsec_init.c
<command line>:2:1: /usr/src/linux/include/linux/modversions.h: No such file or 
directory
In file included from ipsec_init.c:33:
/usr/src/linux/include/linux/malloc.h:4:2: warning: #warning linux/malloc.h is d
eprecated, use linux/slab.h instead.
In file included from /usr/src/linux/include/linux/irq.h:19,
                 from /usr/src/linux/include/asm/hardirq.h:6,
                 from /usr/src/linux/include/linux/interrupt.h:45,
                 from ipsec_init.c:37:
/usr/src/linux/include/asm/irq.h:40: warning: `struct task_struct' declared insi
de parameter list
/usr/src/linux/include/asm/irq.h:40: warning: its scope is only this definition 
or declaration, which is probably not what you want
In file included from /usr/src/linux/include/linux/irq.h:69,
                 from /usr/src/linux/include/asm/hardirq.h:6,
                 from /usr/src/linux/include/linux/interrupt.h:45,
                 from ipsec_init.c:37:
/usr/src/linux/include/asm/hw_irq.h:78: parse error before '(' token
In file included from ipsec_init.c:37:
/usr/src/linux/include/linux/interrupt.h:74: syntax error before "void"
...

  So this needs some fixing up.

		||ugh Daniel
		Testing Fool
		[email protected]

-----BEGIN PGP SIGNATURE-----
Version: 2.6.3ia
Charset: noconv
Comment: For the matching public key, finger the Reply-To: address.

iQCVAwUBPj+JEFZpdJR7FBQRAQG/BwQAx2okFC3CKgJaRpdizAEUItA9E6q0eIVD
ZF60rImUpZP09dCbkdUHEMuUB+ZbGBtojjyOZUVaUqop9ffs3ayhUPb8CGWzHAYM
tud5F1Oey9wgK37cO6hNJO8xBosJavuQJtC0AcKBh4BwOi9tu2U7swc5v24KtJFW
J0I5+YKwDmg=
=Kq0q
-----END PGP SIGNATURE-----