Re: Determining whether gnunet is connected

"Schanzenbach, Martin" <[email protected]> Sat, 26 Feb 2022 08:29:14 +0000
Newsgroups	gmane.network.gnunet.general
Message-ID	<[email protected]>
Hi,

yes our bootstrap peer is acting up lately.
We will try and set it up again for the 0.16.0 release this weekend.

BR
Martin

> On 26. Feb 2022, at 02:04, Bob Ham <[email protected]> wrote:
> 
> Hi Martin,
> 
> That prints nothing:
> 
>  $ gnunet-core
>  $
> 
> Presumably that means there are no connected peers?
> 
> Thanks,
> 
> Bob
> 
> 
> On 25/02/2022 18:53, Schanzenbach, Martin wrote:
>> Hi Bob,
>> 
>> in order to check if you currently have any neighbours (directly connected peers)
>> you can try:
>> 
>> $ gnunet-core
>> 
>> BR
>> Martin
>> 
>>> On 25. Feb 2022, at 19:26, Bob Ham <[email protected]> wrote:
>>> 
>>> Hi there,
>>> 
>>> After having a lot of issues compiling and running different versions
>>> of gnunet sources and packages, I've finally managed to compile the
>>> latest git.  Lots of services are running:
>>> 
>>> $ gnunet-arm -I
>>> Services (excluding stopped services):
>>> (started: 25 / stopped: 21)
>>> ats (binary='gnunet-service-ats', status=started)
>>> cadet (binary='gnunet-service-cadet', status=started)
>>> core (binary='gnunet-service-core', status=started)
>>> datastore (binary='gnunet-service-datastore', status=started)
>>> dht (binary='gnunet-service-dht', status=started)
>>> fs (binary='gnunet-service-fs', status=started)
>>> gns (binary='gnunet-service-gns', status=started)
>>> hostlist (binary='gnunet-daemon-hostlist', status=started)
>>> identity (binary='gnunet-service-identity', status=started)
>>> namecache (binary='gnunet-service-namecache', status=started)
>>> namestore (binary='gnunet-service-namestore', status=started)
>>> nat (binary='gnunet-service-nat', status=started)
>>> nse (binary='gnunet-service-nse', status=started)
>>> peerinfo (binary='gnunet-service-peerinfo', status=started)
>>> peerstore (binary='gnunet-service-peerstore', status=started)
>>> reclaim (binary='gnunet-service-reclaim', status=started)
>>> resolver (binary='gnunet-service-resolver', status=started)
>>> rest (binary='gnunet-rest-server', status=started)
>>> revocation (binary='gnunet-service-revocation', status=started)
>>> setu (binary='gnunet-service-setu', status=started)
>>> statistics (binary='gnunet-service-statistics', status=started)
>>> topology (binary='gnunet-daemon-topology', status=started)
>>> transport (binary='gnunet-service-transport', status=started)
>>> zonemaster (binary='gnunet-service-zonemaster', status=started)
>>> zonemaster-monitor (binary='gnunet-service-zonemaster-monitor', status=started)
>>> 
>>> but I'm not sure what's happening with the node and whether it's
>>> connected to anything.  As per suggestions from IRC, I tried running
>>> "gnunet-transport --information" but it hangs for 30 seconds and then
>>> prints:
>>> 
>>> $ gnunet-transport --information
>>> Failed to list connections, timeout occurred
>>> 
>>> The output of "gnunet-transport --monitor" shows activity but it's
>>> like debug output, it's not clear what the activity is and whether any
>>> successful connections have occurred.
>>> 
>>> The handbook is of no help, it only discusses graphical programs but I
>>> only have terminal access at present.
>>> 
>>> How can I determine whether my node is connected and working?
>>> 
>>> Thanks,
>>> 
>>> Bob Ham
>>> 
>>> --
>>> Bob Ham <[email protected]>
>>> 
>>> for (;;) { ++pancakes; }
>>> 
>>
signature.asc (application/pgp-signature, 833 B)