Re: Determining whether gnunet is connected

"Schanzenbach, Martin" <[email protected]> Sat, 26 Feb 2022 19:53:31 +0000
Newsgroups	gmane.network.gnunet.general
Message-ID	<[email protected]>
Hi Bob,

I think the situation should have improved.
The bootstrap peer was somehow crippled through the configuration to accept
at most 10 peers.

BR
Martin

> On 26. Feb 2022, at 09:29, Schanzenbach, Martin <[email protected]> wrote:
> 
> Hi,
> 
> yes our bootstrap peer is acting up lately.
> We will try and set it up again for the 0.16.0 release this weekend.
> 
> BR
> Martin
> 
>> On 26. Feb 2022, at 02:04, Bob Ham <[email protected]> wrote:
>> 
>> Hi Martin,
>> 
>> That prints nothing:
>> 
>> $ gnunet-core
>> $
>> 
>> Presumably that means there are no connected peers?
>> 
>> Thanks,
>> 
>> Bob
>> 
>> 
>> On 25/02/2022 18:53, Schanzenbach, Martin wrote:
>>> Hi Bob,
>>> 
>>> in order to check if you currently have any neighbours (directly connected peers)
>>> you can try:
>>> 
>>> $ gnunet-core
>>> 
>>> BR
>>> Martin
>>> 
>>>> On 25. Feb 2022, at 19:26, Bob Ham <[email protected]> wrote:
>>>> 
>>>> Hi there,
>>>> 
>>>> After having a lot of issues compiling and running different versions
>>>> of gnunet sources and packages, I've finally managed to compile the
>>>> latest git.  Lots of services are running:
>>>> 
>>>> $ gnunet-arm -I
>>>> Services (excluding stopped services):
>>>> (started: 25 / stopped: 21)
>>>> ats (binary='gnunet-service-ats', status=started)
>>>> cadet (binary='gnunet-service-cadet', status=started)
>>>> core (binary='gnunet-service-core', status=started)
>>>> datastore (binary='gnunet-service-datastore', status=started)
>>>> dht (binary='gnunet-service-dht', status=started)
>>>> fs (binary='gnunet-service-fs', status=started)
>>>> gns (binary='gnunet-service-gns', status=started)
>>>> hostlist (binary='gnunet-daemon-hostlist', status=started)
>>>> identity (binary='gnunet-service-identity', status=started)
>>>> namecache (binary='gnunet-service-namecache', status=started)
>>>> namestore (binary='gnunet-service-namestore', status=started)
>>>> nat (binary='gnunet-service-nat', status=started)
>>>> nse (binary='gnunet-service-nse', status=started)
>>>> peerinfo (binary='gnunet-service-peerinfo', status=started)
>>>> peerstore (binary='gnunet-service-peerstore', status=started)
>>>> reclaim (binary='gnunet-service-reclaim', status=started)
>>>> resolver (binary='gnunet-service-resolver', status=started)
>>>> rest (binary='gnunet-rest-server', status=started)
>>>> revocation (binary='gnunet-service-revocation', status=started)
>>>> setu (binary='gnunet-service-setu', status=started)
>>>> statistics (binary='gnunet-service-statistics', status=started)
>>>> topology (binary='gnunet-daemon-topology', status=started)
>>>> transport (binary='gnunet-service-transport', status=started)
>>>> zonemaster (binary='gnunet-service-zonemaster', status=started)
>>>> zonemaster-monitor (binary='gnunet-service-zonemaster-monitor', status=started)
>>>> 
>>>> but I'm not sure what's happening with the node and whether it's
>>>> connected to anything.  As per suggestions from IRC, I tried running
>>>> "gnunet-transport --information" but it hangs for 30 seconds and then
>>>> prints:
>>>> 
>>>> $ gnunet-transport --information
>>>> Failed to list connections, timeout occurred
>>>> 
>>>> The output of "gnunet-transport --monitor" shows activity but it's
>>>> like debug output, it's not clear what the activity is and whether any
>>>> successful connections have occurred.
>>>> 
>>>> The handbook is of no help, it only discusses graphical programs but I
>>>> only have terminal access at present.
>>>> 
>>>> How can I determine whether my node is connected and working?
>>>> 
>>>> Thanks,
>>>> 
>>>> Bob Ham
>>>> 
>>>> --
>>>> Bob Ham <[email protected]>
>>>> 
>>>> for (;;) { ++pancakes; }
>>>> 
>>> 
>
signature.asc (application/pgp-signature, 833 B)