Re: MRTG and Sonicwall help

So tried all suggestions on the interface config, 

Target[192.168.30.1_X1]: 4:[email protected]:::::2
Target[192.168.30.1_X1]: #X1\ (WAN):[email protected]:
Target[192.168.30.1_X1]: #X1-(WAN):[email protected]:::::2
Target[192.168.30.1_X1]: 1.3.6.1.2.1.2.2.1.10.4&1.3.6.1.2.1.2.2.1.16.4:[email protected]:
Target[192.168.30.1_X1]: 1.3.6.1.2.1.2.2.1.10.4&1.3.6.1.2.1.2.2.1.16.4:[email protected]:::::2

the last one worked, well gave no error in /var/log/mrtg.cfg

but now getting no data / graphs, if I check the IP_XX.log in the /www/mrtg/ folder it just has a timestamp and 4 zeros

1340236800 0 0 0 0
1340150400 0 0 0 0
1340064000 0 0 0 0
1339977600 0 0 0 0
1339891200 0 0 0 0


here is the full snmpwalk against my sonicwall 



Steve, I haven’t changed my interface descriptions since generating the MRTG config file.

would a MIB help ? i haven’t found one for my sonicwall yet, but I need to fine a much easier way to get MRTG gathering data from sonic walls. I have 40 + sonic walls that I need to get monitoring with MRTG 

scot


On Aug 21, 2014, at 10:32, Todd Adamson <[email protected]> wrote:

> You SNMP walk that you show is not far enough.  The OIDs that are used for in and out octets are
> 
> 1.3.6.1.2.1.2.2.1.10.x  (inbound octets)
> and
> 1.3.6.1.2.1.2.2.1.16.x  (outbound octets)
> 
> Where X is the interface number.
> Try replacing your target string with the above with X=4
> 
> Todd
> 
> On 8/20/2014 8:56 PM, scot wrote:
>> I have a sonicwall TZ215, with latest firmware, I am trying to get MRTG to talk to it.
>> 
>> when I run the cfg maker, it talks to the sonicwall and builds a config file with all the sonicwall interfaces… most are commented out.
>> 
>> but I get no graphs
>> 
>> i checked the mrtg.log and have following errors
>> 
>> 2014-08-20 21:02:13 -- 2014-08-20 21:02:13: ERROR: Target[192.168.30.1_x1][_IN_] ' $target->[0]{$mode} ' did not eval into defined data
>> 2014-08-20 21:02:13 -- 2014-08-20 21:02:13: ERROR: Target[192.168.30.1_x1][_OUT_] ' $target->[0]{$mode} ' did not eval into defined data
>> 
>> here is the mrtg.cfg for the interface
>> 
>> Target[192.168.30.1_X1]: #X1:[email protected]:
>> SetEnv[192.168.30.1_X1]: MRTG_INT_IP="No Ip" MRTG_INT_DESCR="X1-(WAN)"
>> MaxBytes[192.168.30.1_X1]: 125000000
>> Title[192.168.30.1_X1]: Traffic Analysis for X1 -- WAN
>> PageTop[192.168.30.1_X1]: <h1>Traffic Analysis for X1 -- WAN</h1>
>> 
>> I tried adding OID’s that I got from a SNMPwalk against the sonciwall,
>> 
>> Target[192.168.30.1_X1]: 3.6.1.2.1.1.2.0&3.6.1.2.1.2.2.1.2.4:[email protected]:
>> 
>> that gives error
>> 
>> 2014-08-20 21:45:30 -- cannot encode Object ID 3.6.1.2.1.1.2.0: first subid too big in Object ID 3.6.1.2.1.1.2.0 at /usr/bin/mrtg line 2339.
>> 2014-08-20 21:45:30 -- 2014-08-20 21:45:30: ERROR: Target[192.168.30.1_x1][_IN_] ' $target->[0]{$mode} ' did not eval into defined data
>> 2014-08-20 21:45:30 -- 2014-08-20 21:45:30: ERROR: Target[192.168.30.1_x1][_OUT_] ' $target->[0]{$mode} ' did not eval into defined data
>> 
>> so the OID’s look like no help … so still no luck on MRTGing my sonicwall
>> 
>> here is the SNMPWALK against the sonciwall
>> 
>> iso.3.6.1.2.1.1.1.0 = STRING: "SonicWALL TZ 215 (SonicOS Enhanced 5.8.1.2-6o)"
>> iso.3.6.1.2.1.1.2.0 = OID: iso.3.6.1.4.1.8741.1
>> iso.3.6.1.2.1.1.3.0 = Timeticks: (698184303) 80 days, 19:24:03.03
>> iso.3.6.1.2.1.1.4.0 = STRING: “WAN ROUTER
>> iso.3.6.1.2.1.1.5.0 = STRING: “RTR-COLO-PIPE_3”
>> iso.3.6.1.2.1.1.6.0 = STRING: “COLO_5
>> iso.3.6.1.2.1.1.7.0 = INTEGER: 79
>> iso.3.6.1.2.1.2.1.0 = INTEGER: 10
>> iso.3.6.1.2.1.2.2.1.1.2 = INTEGER: 2
>> iso.3.6.1.2.1.2.2.1.1.4 = INTEGER: 4
>> iso.3.6.1.2.1.2.2.1.1.6 = INTEGER: 6
>> iso.3.6.1.2.1.2.2.1.1.8 = INTEGER: 8
>> iso.3.6.1.2.1.2.2.1.1.10 = INTEGER: 10
>> iso.3.6.1.2.1.2.2.1.2.2 = STRING: "LOOPBACK"
>> iso.3.6.1.2.1.2.2.1.2.4 = STRING: "X1 (WAN)"
>> iso.3.6.1.2.1.2.2.1.2.6 = STRING: "X3 (Portshielded To X0)"
>> iso.3.6.1.2.1.2.2.1.2.8 = STRING: "X5 (Unassigned)"
>> iso.3.6.1.2.1.2.2.1.2.10 = STRING: "U0 (Unassigned)"
>> iso.3.6.1.2.1.2.2.1.3.2 = INTEGER: 24
>> iso.3.6.1.2.1.2.2.1.3.4 = INTEGER: 6
>> iso.3.6.1.2.1.2.2.1.3.6 = INTEGER: 6
>> iso.3.6.1.2.1.2.2.1.3.8 = INTEGER: 6
>> iso.3.6.1.2.1.2.2.1.3.10 = INTEGER: 1
>> iso.3.6.1.2.1.2.2.1.4.2 = INTEGER: 1536
>> iso.3.6.1.2.1.2.2.1.4.4 = INTEGER: 1500
>> iso.3.6.1.2.1.2.2.1.4.6 = INTEGER: 0
>> iso.3.6.1.2.1.2.2.1.4.8 = INTEGER: 0
>> iso.3.6.1.2.1.2.2.1.4.10 = INTEGER: 0
>> iso.3.6.1.2.1.2.2.1.5.2 = Gauge32: 0
>> iso.3.6.1.2.1.2.2.1.5.4 = Gauge32: 1000000000
>> iso.3.6.1.2.1.2.2.1.5.6 = Gauge32: 0
>> iso.3.6.1.2.1.2.2.1.5.8 = Gauge32: 0
>> iso.3.6.1.2.1.2.2.1.5.10 = Gauge32: 0
>> iso.3.6.1.2.1.2.2.1.6.2 = ""
>> iso.3.6.1.2.1.2.2.1.6.4 = Hex-STRING: C0 EA E4 57 74 95
>> iso.3.6.1.2.1.2.2.1.6.6 = Hex-STRING: C0 EA E4 57 74 97
>> iso.3.6.1.2.1.2.2.1.6.8 = Hex-STRING: C0 EA E4 57 74 99
>> 
>> i’ve been messing with this for days,  and need some help
>> 
>> what am I missing ?
>> 
>> scot
>> _______________________________________________
>> mrtg mailing list
>> [email protected]
>> https://lists.oetiker.ch/cgi-bin/listinfo/mrtg
>> 
>> 
> 
> -- 
> Todd Adamson
> Network Partners, Inc.
> [email protected]
> (402)434-5395 x3001

_______________________________________________
mrtg mailing list
[email protected]
https://lists.oetiker.ch/cgi-bin/listinfo/mrtg