Re: gm_board_info only shows the node itself

Have you run the mapper ?
(active mappers will shop up using port 1)

/etc/init.d/gm start

will start mappers.

Markus

Atsuko Miyashita wrote:

>
> Hi,
>
> I've got a problem that GM mapper only sees the node itself, and
> doesn't communicate each other.
> I appreciate if anybody has a clue/suggestion to this... Thank you in
> advance !
>
> I am currently using GM 2.0.6 and Myrinet "B" card with serial cable.
> I have two nodes(hpc001/hpc002) with Linux 2.4.18-3bigmem(RedHat7.3)
> installed.
> I know the combination of driver/card is not the good one, but this is
> a test environment for some software.
>
> I noticed that I couldn't use MPICH-GM properly, and this was probably
> because of driver layer.
> gm_board_info only shows the node itself, and doesn't show the another
> node.
> I did this several times, but the situation remains the same.
> service gm stop
> service gm start
>
> Also, I changed the physical port(of the switch), but it didn't solve
> the problem.
>
> The odd thing is that I could use the environment without any problem
> for several days.
> I tested the MPICH-GM with its sample program, cpi, and saw it works
> without problem.
> I left the machines for a couple of days and then returned, and saw
> this has happend.
>
> Does anyone have any idea or suggestion, at least how to diag this ?
>
> These are the output of gm_board_info on the each nodes.
>
> [root@hpc001 root]# gm_board_info
> GM build ID is "2.0.6_Linux_rc20030908173009PDT
> root@hpc001:/usr/local/gm-2.0.6_
> Linux Wed Dec 24 16:34:42 JST 2003."
> Board number 0:
> lanai_clockval = 0x082082a0
> lanai_cpu_version = 0x0900 (LANai9.0)
> lanai_board_id = 00:60:dd:7f:61:be
> lanai_sram_size = 0x00200000 (2048K bytes)
> max_lanai_speed = 134 MHz
> product_code = 109
> serial_number = 89434
> (should be labeled: "M3S-PCI64B-2-89434")
> LANai time is 0x058a585f0 ticks, or about 11 minutes since reset.
> Mapper is 00:00:00:00:00:00.
> Map version is 0.
> 0 hosts.
> Network is NOT fully configured.
> This node is "hpc001"
> Board has room for 16 ports, 1600 nodes/routes, 16384 cache entries
> Port token cnt: send=61, recv=254
> Port: Status PID
> 0: BUSY 1503 (this process [gm_board_info])
> Route table for this node follows:
> gmID MAC Address gmName Route
> ---- ----------------- --------------------------------
> ---------------------
> 1 00:60:dd:7f:61:be hpc001 (this node)
>
> [root@hgt002 root]# gm_board_info
> GM build ID is "2.0.6_Linux_rc20030908173009PDT
> root@hgt002:/usr/local/gm-2.0.6_
> Linux Wed Dec 24 17:48:24 JST 2003."
> Board number 0:
> lanai_clockval = 0x082082a0
> lanai_cpu_version = 0x0900 (LANai9.0)
> lanai_board_id = 00:60:dd:7f:61:fc
> lanai_sram_size = 0x00200000 (2048K bytes)
> max_lanai_speed = 134 MHz
> product_code = 109
> serial_number = 89372
> (should be labeled: "M3S-PCI64B-2-89372")
> LANai time is 0x08e6f211a ticks, or about 17 minutes since reset.
> Mapper is 00:00:00:00:00:00.
> Map version is 0.
> 0 hosts.
> Network is NOT fully configured.
> This node is "hgt002"
> Board has room for 16 ports, 1600 nodes/routes, 16384 cache entries
> Port token cnt: send=61, recv=254
> Port: Status PID
> 0: BUSY 1692 (this process [gm_board_info])
> Route table for this node follows:
> gmID MAC Address gmName Route
> ---- ----------------- --------------------------------
> ---------------------
> 1 00:60:dd:7f:61:fc hgt002 (this node)
>
> Thank you in advance for your help !!!
>
> ----------------------------------------------------
> ATSUKO MIYASHITA
> Linux Support Center, SWSC, Technical Support - IBM Japan
> Tel : 03-3808-8993 ( ext. 1712-8993 ) / Fax : 03-3664-4893
> e-mail : ATSUKOMjp.ibm.com
> ** Moved to Hakozaki - mind that tel # has changed ! **
>
>------------------------------------------------------------------------
>
>_______________________________________________
>Myrinet mailing list
>[email protected]
>http://email.osc.edu/mailman/listinfo/myrinet
>  
>