Re: cpu usage through UCD-SNMP-MIB::systemStats
"toc2 techie" <[email protected]>
| Newsgroups | gmane.network.net-snmp.user |
|---|---|
| Message-ID | <[email protected]> |
HI, below is what you asked for. On 2/22/07, Thomas Anders <[email protected]> wrote: > > toc2 techie wrote: > >>> What's the exact output of these commands? > > There is no output > > That's somewhat strange. Can you please add "-d" to the (beginning of > the) command-line options and post the *full* output you get? bash$ snmpwalk -d -v1 -c public <ip> UCD-SNMP-MIB::systemStats Sending 43 bytes to <ip> 0000: 30 29 02 01 00 04 06 70 75 62 6C 69 63 A1 1C 02 0).....public... 0016: 04 6D 95 B8 81 02 01 00 02 01 00 30 0E 30 0C 06 .m.........0.0.. 0032: 08 2B 06 01 04 01 8F 65 0B 05 00 .+.....e... Received 46 bytes from <ip> 0000: 30 2C 02 01 00 04 06 70 75 62 6C 69 63 A2 1F 02 0,.....public... 0016: 04 6D 95 B8 81 02 01 00 02 01 00 30 11 30 0F 06 .m.........0.0.. 0032: 0A 2B 06 01 04 01 8F 65 64 01 00 02 01 01 .+.....ed..... Sending 43 bytes to <ip> 0000: 30 29 02 01 00 04 06 70 75 62 6C 69 63 A0 1C 02 0).....public... 0016: 04 6D 95 B8 82 02 01 00 02 01 00 30 0E 30 0C 06 .m.........0.0.. 0032: 08 2B 06 01 04 01 8F 65 0B 05 00 .+.....e... Received 43 bytes from <ip> 0000: 30 29 02 01 00 04 06 70 75 62 6C 69 63 A2 1C 02 0).....public... 0016: 04 6D 95 B8 82 02 01 02 02 01 01 30 0E 30 0C 06 .m.........0.0.. 0032: 08 2B 06 01 04 01 8F 65 0B 05 00 .+.....e... >>> What's the output of "net-snmp-config --configure-options"? > > I didn't find any such command or file on my box > > Asking differently, then: Is this a manual installation or a package? Is > the source an unmodified net-snmp 5.3.0.1 as shipped by us? How > *exactly* (with what configure options) has it been built? will find out about this. Its not rpm based one. Also, what's the full content of your snmpd.conf and how exactly do you > start your snmpd? snmpd is starte as snmpd -c /etc/snmpd.conf. contents of snmpd.conf ############################################################################### # Access Control ############################################################################### # # Enable read-only access for the "public" community. rocommunity public ############################################################################### # System contact information ############################################################################### # # Set the sysLocation and sysContact system variables. syslocation B3 syscontact System administrator ############################################################################### # Enable AgentX functionality for the OpenHPI Subagent ############################################################################### master agentx agentXTimeout 5 +Thomas > > -- > Thomas Anders (thomas.anders at blue-cable.de) > ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________ Net-snmp-users mailing list [email protected] Please see the following page to unsubscribe or change other options: https://lists.sourceforge.net/lists/listinfo/net-snmp-users