| Newsgroups |
gmane.network.net-snmp.user |
| Message-ID |
<[email protected]> |
I am desperately seeking some help as I am really struggling, but I accept
this isn't really the remit of this list - if its more appropriate off list
replies are fine by me.
I have net-snmp installed and apparently working e.g. snmpget returns
values from localhost.
I now want to test sending traps to a HP Openview Network Node Manager (I
am told this is what should be happening - I inherited a very very partial
OV installation and am trying to make it work with no budget and little
background. Aren't I lucky?!).
I have run snmp-config and nominated the NNM server as the receiver of
traps (snmpd.conf attached below - some of the triggers are deliberately
set to create traps at the moment for test ppurposes).
I can issue commands like
bash-3.00# snmptrap -v 2c -c public localhost "" UCD-SNMP-MIB::ucdStart
bash-3.00# snmptrap -v 2c -c public localhost "" .1.3.6.1.4.1.2021.251.1
bash-3.00# snmptrap -v 2c -c public localhost "" ucdStart sysContact.0 s
"Dave"
- but nothing ever appears in NNM. If I restart the snmpd daemon then an
alarm does appear then in NNM noting this - but that's is all I ever see
there.
Any pointers or other help greatefully received. I have no idea where to
go from here :-(
cheers
ian
---
###########################################################################
#
# snmpd.conf
#
# - created by the snmpconf configuration program
#
###########################################################################
# SECTION: System Information Setup
#
# This section defines some of the information reported in
# the "system" mib group in the mibII tree.
# syslocation: The [typically physical] location of the system.
# Note that setting this value here means that when trying to
# perform an snmp SET operation to the sysLocation.0 variable will make
# the agent return the "notWritable" error code. IE, including
# this token in the snmpd.conf file will disable write access to
# the variable.
# arguments: location_string
syslocation upstairs
# syscontact: The contact information for the administrator
# Note that setting this value here means that when trying to
# perform an snmp SET operation to the sysContact.0 variable will make
# the agent return the "notWritable" error code. IE, including
# this token in the snmpd.conf file will disable write access to
# the variable.
# arguments: contact_string
syscontact "ian diddams"
###########################################################################
# SECTION: Access Control Setup
#
# This section defines who is allowed to talk to your running
# snmp agent.
# rwuser: a SNMPv3 read-write user
# arguments: user [noauth|auth|priv] [restriction_oid]
rwuser private
# rouser: a SNMPv3 read-only user
# arguments: user [noauth|auth|priv] [restriction_oid]
rouser public
# rocommunity: a SNMPv1/SNMPv2c read-only access community name
# arguments: community [default|hostname|network/bits] [oid]
rocommunity public
# rwcommunity: a SNMPv1/SNMPv2c read-write access community name
# arguments: community [default|hostname|network/bits] [oid]
rwcommunity private
###########################################################################
# SECTION: Trap Destinations
#
# Here we define who the agent will send traps to.
# trapsink: A SNMPv1 trap receiver
# arguments: host [community] [portnum]
trapsink msnm2 162
# trap2sink: A SNMPv2c trap receiver
# arguments: host [community] [portnum]
trap2sink msnm2 162
# informsink: A SNMPv2c inform (acknowledged trap) receiver
# arguments: host [community] [portnum]
informsink msnm2 162
# trapcommunity: Default trap sink community to use
# arguments: community-string
trapcommunity public
# authtrapenable: Should we send traps when authentication failures occur
# arguments: 1 | 2 (1 = yes, 2 = no)
authtrapenable 1
###########################################################################
# SECTION: Monitor Various Aspects of the Running Host
#
# The following check up on various aspects of a host.
# proc: Check for processes that should be running.
# proc NAME [MAX=0] [MIN=0]
#
# NAME: the name of the process to check for. It must match
# exactly (ie, http will not find httpd processes).
# MAX: the maximum number allowed to be running. Defaults to 0.
# MIN: the minimum number to be running. Defaults to 0.
#
# The results are reported in the prTable section of the UCD-SNMP-MIB tree
# Special Case: When the min and max numbers are both 0, it assumes
# you want a max of infinity and a min of 1.
proc sendmail 2 2
# disk: Check for disk space usage of a partition.
# The agent can check the amount of available disk space, and make
# sure it is above a set limit.
#
# disk PATH [MIN=100000]
#
# PATH: mount path to the disk in question.
# MIN: Disks with space below this value will have the Mib's errorFlag
set.
# Can be a raw byte value or a percentage followed by the %
# symbol. Default value = 100000.
#
# The results are reported in the dskTable section of the UCD-SNMP-MIB
tree
disk / 33977010
# load: Check for unreasonable load average values.
# Watch the load average levels on the machine.
#
# load [1MAX=12.0] [5MAX=12.0] [15MAX=12.0]
#
# 1MAX: If the 1 minute load average is above this limit at query
# time, the errorFlag will be set.
# 5MAX: Similar, but for 5 min average.
# 15MAX: Similar, but for 15 min average.
#
# The results are reported in the laTable section of the UCD-SNMP-MIB tree
load 0.01 0.01 0.01
# file: Check on the size of a file.
# Display a files size statistics.
# If it grows to be too large, report an error about it.
#
# file /path/to/file [maxsize_in_bytes]
#
# if maxsize is not specified, assume only size reporting is needed.
#
# The results are reported in the fileTable section of the UCD-SNMP-MIB
tree
file /var/adm/messages 1024
--------------------------------------------------------------------
mail2web LIVE Free email based on Microsoft® Exchange technology -
http://link.mail2web.com/LIVE
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take
control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
_______________________________________________
Net-snmp-users mailing list
[email protected]
Please see the following page to unsubscribe or change other options:
https://lists.sourceforge.net/lists/listinfo/net-snmp-users