RE: net-snmp with solarwinds on aix
"Derek Smith" <[email protected]>
| Newsgroups | gmane.network.net-snmp.user |
|---|---|
| Message-ID | <[email protected]> |
Will anyone share their working snmpd.conf file so that I can compare. I was able to get the volumes recognized, but Solarwinds is just displaying the names Of these volumes. Thx! From: Derek Smith Sent: Wednesday, September 14, 2011 9:53 AM To: '[email protected]' Subject: net-snmp with solarwinds on aix I configured using the file text below. Solarwinds is our monitoring software that runs on a Windows server which sends alerts. When I access the GUI on the SW server, then select resources, I do not see any of my filesystems (disk volumes). I only see RAM, VRAM and Swap. I need for solarwinds to see my disks! Please help. ThnkU! The highlighted lines are active and below this is my startup as root. # cat snmpd.conf.orig ############################################################################### # # EXAMPLE.conf: # An example configuration file for configuring the Net-SNMP agent ('snmpd') # See the 'snmpd.conf(5)' man page for details # # Some entries are deliberately commented out, and will need to be explicitly activated # ############################################################################### # # AGENT BEHAVIOUR # # Listen for connections from the local system only # Listen for connections on all interfaces (both IPv4 *and* IPv6) agentAddress udp:161,udp6:[::1]:161 ############################################################################### # # SNMPv3 AUTHENTICATION # # Note that these particular settings don't actually belong here. # They should be copied to the file /var/net-snmp/snmpd.conf # and the passwords changed, before being uncommented in that file *only*. # Then restart the agent # createUser authOnlyUser MD5 "remember to change this password" # createUser authPrivUser SHA "remember to change this one too" DES # createUser internalUser MD5 "this is only ever used internally, but still change the password" # If you also change the usernames (which might be sensible), # then remember to update the other occurances in this example config file to match. ############################################################################### # # ACCESS CONTROL # #rocommunity cbcunix1 rocommunity cbcunix1 cbc-orion01 # system + hrSystem groups only #view systemonly included .1.3.6.1.2.1.1 #view systemonly included .1.3.6.1.2.1.25.1 # Full access from the local host #rocommunity public localhost # Default access to basic system info # rocommunity public default -V systemonly # Full access from an example network # Adjust this network address to match your local # settings, change the community string, # and check the 'agentAddress' setting above #rocommunity secret 10.0.0.0/16 # Full read-only access for SNMPv3 # rouser authOnlyUser # Full write access for encrypted requests # Remember to activate the 'createUser' lines above #rwuser authPrivUser priv # It's no longer typically necessary to use the full 'com2sec/group/access' configuration # r[ou]user and r[ow]community, together with suitable views, should cover most requirements ############################################################################### # # SYSTEM INFORMATION # # Note that setting these values here, results in the corresponding MIB objects being 'read-only' # See snmpd.conf(5) for more details #sysLocation Sitting on the Dock of the Bay #sysContact Me <[email protected]> # Application + End-to-End layers #sysServices 72 # # Process Monitoring # # At least one 'mountd' process #proc mountd # No more than 4 'ntalkd' processes - 0 is OK #proc ntalkd 4 # # At least one 'sendmail' process, but no more than 10 #proc sendmail 10 1 # Walk the UCD-SNMP-MIB::prTable to see the resulting output # Note that this table will be empty if there are no "proc" entries in the snmpd.conf file # # Disk Monitoring # # 10MBs required on root disk, 5% free on /var, 10% free on all other disks #disk / 10000 #disk /var 5% #includeAllDisks 10% # Walk the UCD-SNMP-MIB::dskTable to see the resulting output # Note that this table will be empty if there are no "disk" entries in the snmpd.conf file # # System Load # # Unacceptable 1-, 5-, and 15-minute load averages #load 12 10 5 # Walk the UCD-SNMP-MIB::laTable to see the resulting output # Note that this table *will* be populated, even without a "load" entry in the snmpd.conf file ############################################################################### # # ACTIVE MONITORING # # send SNMPv1 traps # trapsink localhost public # send SNMPv2c traps trap2sink cbc-orion01 cbcunix1 # send SNMPv2c INFORMs informsink cbc-orion01 cbcunix1 # Note that you typically only want *one* of these three lines # Uncommenting two (or all three) will result in multiple copies of each notification. # # Event MIB - automatically generate alerts # # Remember to activate the 'createUser' lines above iquerySecName internalUser rouser internalUser # # generate traps on UCD error conditions defaultMonitors yes # generate traps on linkUp/Down linkUpDownNotifications yes ############################################################################### # # EXTENDING THE AGENT # # # Arbitrary extension commands # # extend test1 /bin/echo Hello, world! # extend-sh test2 echo Hello, world! ; echo Hi there ; exit 35 #extend-sh test3 /bin/sh /tmp/shtest # Note that this last entry requires the script '/tmp/shtest' to be created first, # containing the same three shell commands, before the line is uncommented # Walk the NET-SNMP-EXTEND-MIB tables (nsExtendConfigTable, nsExtendOutput1Table # and nsExtendOutput2Table) to see the resulting output # Note that the "extend" directive supercedes the previous "exec" and "sh" directives # However, walking the UCD-SNMP-MIB::extTable should still returns the same output, # as well as the fuller results in the above tables. # # "Pass-through" MIB extension command # #pass .1.3.6.1.4.1.8072.2.255 /bin/sh PREFIX/local/passtest #pass .1.3.6.1.4.1.8072.2.255 /usr/bin/perl PREFIX/local/passtest.pl # Note that this requires one of the two 'passtest' scripts to be installed first, # before the appropriate line is uncommented. # These scripts can be found in the 'local' directory of the source distribution, # and are not installed automatically. # Walk the NET-SNMP-PASS-MIB::netSnmpPassExamples subtree to see the resulting output # # AgentX Sub-agents # # Run as an AgentX master agent # master agentx # Listen for network connections (from localhost) # rather than the default named socket /var/agentx/master #agentXSocket tcp:localhost:705 --------------------------------------------------------------------------------------------------------------------------------- # /opt/freeware/sbin/snmpd -p /var/run/snmpd.pid -a MIB search path: /root/.snmp/mibs:/opt/freeware/share/snmp/mibs Cannot find module (SNMPv2-SMI): At line 34 in /opt/freeware/share/snmp/mibs/UCD-SNMP-MIB.txt Cannot find module (SNMPv2-TC): At line 37 in /opt/freeware/share/snmp/mibs/UCD-SNMP-MIB.txt Cannot find module (UCD-SNMP-MIB): At line 0 in (none) Cannot find module (UCD-DEMO-MIB): At line 0 in (none) Cannot find module (SNMP-FRAMEWORK-MIB): At line 24 in /opt/freeware/share/snmp/mibs/SNMP-TARGET-MIB.txt Cannot find module (SNMP-TARGET-MIB): At line 0 in (none) Cannot find module (NET-SNMP-MIB): At line 12 in /opt/freeware/share/snmp/mibs/NET-SNMP-AGENT-MIB.txt Cannot find module (NET-SNMP-AGENT-MIB): At line 0 in (none) Cannot find module (SNMPv2-MIB): At line 13 in /opt/freeware/share/snmp/mibs/DISMAN-EVENT-MIB.txt Cannot find module (DISMAN-EVENT-MIB): At line 0 in (none) Cannot find module (IANAifType-MIB): At line 13 in /opt/freeware/share/snmp/mibs/IF-MIB.txt Cannot find module (IF-MIB): At line 12 in /opt/freeware/share/snmp/mibs/HOST-RESOURCES-MIB.txt Cannot find module (HOST-RESOURCES-MIB): At line 0 in (none) Cannot find module (HOST-RESOURCES-TYPES): At line 0 in (none) Cannot find module (UCD-DISKIO-MIB): At line 0 in (none) Cannot find module (NETWORK-SERVICES-MIB): At line 13 in /opt/freeware/share/snmp/mibs/MTA-MIB.txt Cannot find module (MTA-MIB): At line 0 in (none) Cannot find module (RMON-MIB): At line 0 in (none) Cannot find module (EtherLike-MIB): At line 0 in (none) Cannot find module (INET-ADDRESS-MIB): At line 15 in /opt/freeware/share/snmp/mibs/IP-MIB.txt Cannot find module (IP-MIB): At line 0 in (none) Cannot find module (TCP-MIB): At line 0 in (none) Cannot find module (UDP-MIB): At line 0 in (none) Cannot find module (NOTIFICATION-LOG-MIB): At line 0 in (none) Cannot find module (DISMAN-SCHEDULE-MIB): At line 0 in (none) Cannot find module (SNMP-MPD-MIB): At line 0 in (none) Cannot find module (SNMP-USER-BASED-SM-MIB): At line 0 in (none) Cannot find module (SNMP-VIEW-BASED-ACM-MIB): At line 0 in (none) Cannot find module (SNMP-COMMUNITY-MIB): At line 0 in (none) Cannot find module (NET-SNMP-EXAMPLES-MIB): At line 11 in /opt/freeware/share/snmp/mibs/NET-SNMP-PASS-MIB.txt Cannot find module (NET-SNMP-PASS-MIB): At line 0 in (none) Cannot find module (NET-SNMP-EXTEND-MIB): At line 0 in (none) Cannot find module (UCD-DLMOD-MIB): At line 0 in (none) Cannot find module (SNMP-NOTIFICATION-MIB): At line 0 in (none) Cannot find module (SNMPv2-TM): At line 0 in (none) Cannot find module (NET-SNMP-VACM-MIB): At line 0 in (none) ------------------------------------------------------------------------------ BlackBerry® DevCon Americas, Oct. 18-20, San Francisco, CA http://p.sf.net/sfu/rim-devcon-copy2 _______________________________________________ Net-snmp-users mailing list [email protected] Please see the following page to unsubscribe or change other options: https://lists.sourceforge.net/lists/listinfo/net-snmp-users