nagios snmp checks

I've got a nagios/snmp question that I've been struggling with. I've
downloaded the super micro MIB files directly from their websites. I did an
snmpwalk to view the data that it pulls by default. I, then, added the MIB
files in /usr/share/snmp/mibs directory and ran the following command:

snmptranslate -m +SUPERMICRO-HEALTH-MIB -IR -On smHealthMonitorMinReading
.1.3.6.1.4.1.10876.2.1.1.1.1.8

 ./check_snmp -H 192.168.31.116 -C orchard -o .
*1.3.6.1.4.1.10876.2.1.1.1.1.8*

SNMP CRITICAL - Unknown error: 2


I wasn't sure why it thew that error message, so I ran a snmpwalk to pull
the OID mapping and ran the following:

[root@nagios02 ~]# ./check_snmp -H 192.168.XX.XX -C $COMM -o .
*1.3.6.1.4.1.10876.2.1.1.1.1.2.11*
SNMP OK - CPU1 Vcore Voltage


snmpwalk -v 2c -c orchard 192.168.XX.XX SUPERMICRO -O n
.1.3.6.1.4.1.10876.2.1.1.1.1.2.1 = STRING: Fan1 Fan Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.2 = STRING: Fan2 Fan Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.3 = STRING: Fan3 Fan Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.4 = STRING: Fan4 Fan Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.5 = STRING: FanA Fan Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.6 = STRING: FanB Fan Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.7 = STRING: Power1 Fan 1 Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.8 = STRING: Power1 Fan 2 Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.9 = STRING: Power2 Fan 1 Speed
.1.3.6.1.4.1.10876.2.1.1.1.1.2.10 = STRING: Power2 Fan 2 Speed
*.1.3.6.1.4.1.10876.2.1.1.1.1.2.11 = STRING: CPU1 Vcore Voltage*
.1.3.6.1.4.1.10876.2.1.1.1.1.2.12 = STRING: CPU2 Vcore Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.13 = STRING: CPU1 VDIMM Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.14 = STRING: CPU2 VDIMM Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.15 = STRING: -12V Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.16 = STRING: +5VSB Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.17 = STRING: VTT Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.18 = STRING: +1.5V Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.19 = STRING: +5V Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.20 = STRING: +12V Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.21 = STRING: +3.3V Voltage
.1.3.6.1.4.1.10876.2.1.1.1.1.2.22 = STRING: +3.3VSB Voltage


What may be a dumb question...

How in the world can I get the true status instead of stating what the
string is. In other words, What is the current voltage of the below? I get
the same value that is shown in snmpwalk, when I am looking for the value
of the voltage reading


-- 
* Nikhil Shah */ System Administrator

[email protected]


*The Orchard(R)* / www.theorchard.com

t (+1) 212.308.5648 / f (+1) 212.201.9203
23 E. 4th St., 3rd Fl / New York, NY 10003

The Daily Rind(tm) / *www.dailyrindblog.com* <http://www.dailyrindblog.com/>

*Facebook* <http://www.facebook.com/theorchard> /
*@orchtweets*<http://www.twitter.com/orchtweets>

Privileged And Confidential Communication.

This electronic transmission, and any documents attached hereto, (a) are
protected by the Electronic Communications Privacy Act (18 USC §§
2510-2521), (b) may contain confidential and/or legally privileged
information, and (c) are for the sole use of the intended recipient named
above. If you have received this electronic message in error, please notify
the sender and delete the electronic message. Any disclosure, copying,
distribution, or use of the contents of the information received in error
is strictly prohibited

------------------------------------------------------------------------------
Managing the Performance of Cloud-Based Applications
Take advantage of what the Cloud has to offer - Avoid Common Pitfalls.
Read the Whitepaper.
http://pubads.g.doubleclick.net/gampad/clk?id=121054471&iu=/4140/ostg.clktrk

_______________________________________________
Net-snmp-users mailing list
[email protected]
Please see the following page to unsubscribe or change other options:
https://lists.sourceforge.net/lists/listinfo/net-snmp-users