Re: SNMPv3 Debian Question
Pushpa Thimmaiah <[email protected]>
| Newsgroups | gmane.network.net-snmp.user |
|---|---|
| Message-ID | <CAASqVJV9dwbT1KXJ_0O81ajJJXjsEXfMH2kQCmCf0-Bd0dyP3g@mail.gmail.com> |
Hi Jayashankar, Yes. It should. However, I havenot verified. Thanks, Pushpa.T On Sat, May 27, 2017 at 11:14 AM, jayshankar nair <[email protected] > wrote: > Hi Pushpa, > > I was wondering whether commenting sysContact.0 in snmpd.conf file will > make it writeable again. Hence snmpset will execute successfully. > > Please let me know. > > Thanks, > Jayshankar > > On Thu, May 25, 2017 at 1:33 PM, Pushpa Thimmaiah < > [email protected]> wrote: > >> Hi Jayshankar, >> >> Because system.sysContact.0 is read-only. snmpd.conf on your device >> could have directive 'sysContact'. >> snmpd.conf manpage says that specifying sysContact directives in >> snmpd.conf makes the corresponding object read-only, and attempts to SET >> it will result in a *notWritable* error response. >> >> Thanks, >> Pushpa.T >> >> On Wed, May 24, 2017 at 10:55 AM, jayshankar nair < >> [email protected]> wrote: >> >>> Hi, >>> >>> I am testing snmpset with snmpv3 rwuser myuser2. I am getting the below >>> errors. >>> >>> snmpset -v 3 -u myuser2 -l authNoPriv -a MD5 -A my_password localhost >>> system.sysContact.0 s [email protected]‐gers.edu >>> Error in packet. >>> Reason: notWritable (That object does not support modification) >>> Failed object: SNMPv2-MIB::sysContact.0 >>> >>> snmpget works fine. >>> SNMPv2-MIB::sysContact.0 = STRING: Alice. >>> >>> >>> >>> >>> Thanks, >>> Jayshankar >>> >>> On Wed, May 24, 2017 at 4:08 AM, Wes Hardaker < >>> [email protected]> wrote: >>> >>>> "Jan-Philipp Schollbach" <[email protected]> writes: >>>> >>>> > I configured by snmpd an v3 User with the command --> >>>> > sudo net-snmp-create-v3-user -ro -A 11111111 -a SHA -X 22222222 -x >>>> AES trap1111 >>>> >>>> Was the snmpd agent running when you ran that command? It actually >>>> can't be. To add new users via the CLI, you need to stop the agent, run >>>> the command, and then restart it. >>>> >>>> (once you have an initial user configured, you can use snmpusm command >>>> to add new users to a live agent) >>>> -- >>>> Wes Hardaker >>>> USC/ISI >>>> >>>> ------------------------------------------------------------ >>>> ------------------ >>>> Check out the vibrant tech community on one of the world's most >>>> engaging tech sites, Slashdot.org! http://sdm.link/slashdot >>>> _______________________________________________ >>>> Net-snmp-users mailing list >>>> [email protected] >>>> Please see the following page to unsubscribe or change other options: >>>> https://lists.sourceforge.net/lists/listinfo/net-snmp-users >>>> >>> >>> >>> ------------------------------------------------------------ >>> ------------------ >>> Check out the vibrant tech community on one of the world's most >>> engaging tech sites, Slashdot.org! http://sdm.link/slashdot >>> _______________________________________________ >>> Net-snmp-users mailing list >>> [email protected] >>> Please see the following page to unsubscribe or change other options: >>> https://lists.sourceforge.net/lists/listinfo/net-snmp-users >>> >>> >> > ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Net-snmp-users mailing list [email protected] Please see the following page to unsubscribe or change other options: https://lists.sourceforge.net/lists/listinfo/net-snmp-users