Re: Re: snmptrap v3 how to specify source IP

Klemen Sladic <[email protected]>
Newsgroups gmane.network.net-snmp.user
Message-ID <CAN6eUaG4107rgMvMiw7Vcsqj3Z_opQSuSg1ZR8-CQuFs7Rrrhg@mail.gmail.com>
By routing decision, as I noted before.

RegK

On Fri, May 24, 2019 at 3:23 PM ww <[email protected]> wrote:

> Hi.
> Thanks for your reply. I try to use "-s" and "--clientaddr" but it dose
> not work.
> My version is net-snmp-5.8.
> My commond is "snmptrap -v3 -u usertest -l authPriv -a SHA -A usertest  -x
> AES -X usertest  -s 10.2.24.121  10.2.24.18 84100 …… ".
> May I ask you how the snmptrap chooses the network interface by it self?
> Is it polling all the enable ports?
>
> Regards
>
> At 2019-05-23 15:54:28, "Klemen Sladic" <[email protected]> wrote:
>
> Hi.
>
> Any traffic originating from snmpd will have src IP of outgoing network
> interface.
> From my experience "clientaddr" helps for replies generated by snmpd. For
> example,
> if you have multiple interfaces and "clientaddr" is set, any snmpd
> response, like response to
> snmpget, snmpwalk etc. will have desired src IP.
>
> But this won't work for packets initiated by snmpd, like traps.
> What I did, was changing the route src settings.
> For example, if you have eth0 in 192.168.0.0/24 and eth1 in 192.168.1.0/24
> and you want any traffic to
> have source of 192.168.0.0/24, then change eth1 subnet route like:
>
> ip route change 192.168.1.0/24 dev eth1 src 192.168.0.1
>
> if 192.168.0.1 is eth0 IP.
>
> Of course this may have other side effects on routing in your system.
>
> RegK
>
> On Thu, May 23, 2019 at 6:30 PM Anders Wallin <[email protected]> wrote:
>
>> You can use "clientaddr" in snmp.conf or snmpd.conf,
>> https://linux.die.net/man/5/snmp.conf
>>
>> In 5.8 you also have the possibility to use "-s" with trapsess, but I did
>> not found any documentation on it.
>> but check the test
>> code, testing/fulltests/default/T184trapsesssource_simple
>>
>> Regards
>> Anders Wallin
>>
>>
>> On Wed, May 22, 2019 at 5:21 PM ww <[email protected]> wrote:
>>
>>> Hello, Thank you for reading my email. Can I specify the source IP when
>>> send a V2/V3 trap like V1?
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> Net-snmp-users mailing list
>>> [email protected]
>>> Please see the following page to unsubscribe or change other options:
>>> https://lists.sourceforge.net/lists/listinfo/net-snmp-users
>>>
>> _______________________________________________
>> Net-snmp-users mailing list
>> [email protected]
>> Please see the following page to unsubscribe or change other options:
>> https://lists.sourceforge.net/lists/listinfo/net-snmp-users
>>
>
>
>
>

_______________________________________________
Net-snmp-users mailing list
[email protected]
Please see the following page to unsubscribe or change other options:
https://lists.sourceforge.net/lists/listinfo/net-snmp-users
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.