Re: [f-nsp] Does VRF still take CAM resources from 'ipv4 vpn' in later MLXe code?

Dear David,

I just heard back from my SE and it seems that your RFE has been "returned"
ie rejected in June 2016.

Best regards.



2016-08-31 20:10 GMT+02:00 Youssef Bengelloun-Zahr <[email protected]>:

> I can always ask my SE to check its' status on my end.
>
> I'll be definitly interested if you get a feedback.
>
> Best regards.
>
>
>
> Le 31 août 2016 à 19:43, David Hubbard <[email protected]> a
> écrit :
>
> Ah, good catch, I forgot about the RFE.  It’s 102535.  I’ll attempt to
> find its status.
>
>
>
> *From: *Youssef Bengelloun-Zahr <[email protected]>
> *Date: *Wednesday, August 31, 2016 at 12:36 PM
> *To: *David Hubbard <[email protected]>
> *Cc: *"[email protected]" <[email protected]>
> *Subject: *Re: [f-nsp] Does VRF still take CAM resources from 'ipv4 vpn'
> in later MLXe code?
>
>
>
> Dear David,
>
>
>
> I'm in the exact same case. I have started seeing those exact IPv6 CAM
> error related messages 3 weeks ago. Interestingly enough, only getting
> those for MLXe boxes and not CER-RT.
>
>
>
> I'm running 5.7e and about to upgrade to 5.8e.
>
>
>
> If memory serves right, I think I read something in some release notes (or
> other documentation) about a special feature/profil that would accomodate
> CAM for 1 VRF. I can't seem to recall which, so I'd invite you to read the
> litterature.
>
>
>
> Also, IIRC, I think I read That someone put up an RFE for this following
> your thread two years ago.
>
>
>
> Best regards.
>
>
>
>
>
>
> Le 31 août 2016 à 18:20, David Hubbard <[email protected]> a
> écrit :
>
> Hey all, in 2014 I ran into an issue where I converted an MLXe to the
> ipv4-ipv6-2 profile to get maximum routes for both.  When I did that, I
> lost management access because I use management VRF’s, and those require
> resources from the ‘IPv4 VPN’ segment of CAM.  The ipv4-ipv6-2 profile sets
> that to zero.  So, I switched to multi-service-4 as a workaround since it
> still had enough room.
>
>
>
> Fast forward two years and IPv6 adoption has increased to the point where
> an MLXe with –X cards is just about out of CAM if it’s acting as an
> internet router and using the multi-service-4 profile.  Starting to see
> these alerts:
>
>
>
> Aug 31 11:51:10:A:CAM IPv6 partition warning: total 32768 (reserved 0),
> free 1602, slot 3, ppcr 1
>
>
>
> because internet routers are seeing roughly 31,000 IPv6 advertisements now
> and multi-service-4 only has room for 32k.
>
>
>
> At the time, there was no way to configure custom CAM values, such as my
> desired goal of 768k minus 1 ipv4, 64k ipv6, 1 IPv4 VPN to facilitate one
> VRF.  I didn’t want to use ipv4-ipv6-2 either since I like having the VRF.
>
>
>
> Is there any workaround for this issue in later code releases?
>
>
>
> Thanks,
>
>
>
> David
>
> _______________________________________________
> foundry-nsp mailing list
> [email protected]
> http://puck.nether.net/mailman/listinfo/foundry-nsp
>
>


-- 
Youssef BENGELLOUN-ZAHR

_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp