Re: [f-nsp] AAA, TACACS, some users enabled on login, others not

Send tac_plus.conf & aaa config

On Wed, Nov 16, 2016 at 5:09 AM, Tom Storey <[email protected]> wrote:

> Hi Daniel,
>
> I hadnt tried the brocade-privlvl AV pair before, so I gave that a try,
> but still that didnt seem to enable me upon login.
>
> Either the TACACS server isnt sending the AV pair (although I believe it
> is, because if it is not made optional, then I cant login to Cisco devices
> for example), or the Brocades are just ignoring them or Im just doing
> something really wrong...
>
>
> On 15 November 2016 at 17:06, Daniel Schmidt <[email protected]>
> wrote:
>
>> Brocade has the brocade specific brocade-privlvl, with three different
>> levels of access as I remember, 1, 4 and 5.  The mapping between the two is
>> not always good.  For instance, on Brocade, as I remember, 1 on Cisco maps
>> to 4 of Brocade, which is just stupid - it should map to 5.  (Granted, this
>> was years ago, it may have changed)  As a shameless plug, it's not hard to
>> do modify this with tac_plus & do_auth provided you can distinguish by
>> device IP.  You can authorize by priv levels or commands.  I wrote about it
>> years ago here:
>>
>> http://www.tacacs.org/tacacsplus/2012/02/06/disable-account-on-brocade
>>
>> On Sat, Nov 5, 2016 at 1:32 PM, Eldon Koyle <
>> [email protected]> wrote:
>>
>>> I did notice that document says privlvl and not priv-lvl.  Depending on
>>> what you changed, you may be able to see the enable attempt on the tacacs
>>> server (it may just be expecting the same username/password with admin
>>> privs on tacacs).
>>>
>>> On Nov 5, 2016 11:06 AM, "Tom Storey" <[email protected]> wrote:
>>>
>>>> Hi Eldon,
>>>>
>>>> Thanks for pointing me to this document.
>>>>
>>>> If I understand it correctly, my existing configuration should have
>>>> been working just fine as it is. Since I wasnt specifying the
>>>> "foundry-privlvl" attribute, it should look for the last exec attribute
>>>> with a number in it and treat that number as the priv level. In my case Im
>>>> using "priv-lvl" with a value of 15 for my Cisco devices, so the Brocade
>>>> should have translated that to mean level 0 given a lack of
>>>> "foundry-privlvl" attribute.
>>>>
>>>> But for what ever reason that doesnt seem to be working. So I also
>>>> tried specifying it explicitly in my config, including removing the
>>>> priv-lvl attribute, but still to no avail.
>>>>
>>>> Ive managed to lock myself out of my test device now (can no longer
>>>> enable, its asking for a username, doh!), its in the office and Im at home.
>>>> So I guess I'll resume on Monday if anyone else comes up with anything. :-)
>>>>
>>>> Thanks
>>>> Tom
>>>>
>>>> On 4 November 2016 at 20:53, Eldon Koyle <ekoyle+puck.nether.net@gmail.
>>>> com> wrote:
>>>>
>>>>> We use foundry-privlvl = 0 for admin access.
>>>>>
>>>>> See also: http://www.brocade.com/content/html/en/configuration-guide/F
>>>>> I_08030_SECURITY/GUID-A2449097-2DA4-4CD1-B2DA-C531D7A90587.html
>>>>>
>>>>> --
>>>>> Eldon
>>>>>
>>>>> On Fri, Nov 4, 2016 at 5:26 AM, Tom Storey <[email protected]> wrote:
>>>>> > Hi everyone,
>>>>> >
>>>>> > Implementing a TACACS server for a network that I am working on, and
>>>>> I am
>>>>> > trying to determine how to have certain users (e.g. network admins)
>>>>> enabled
>>>>> > by default once they have logged in, but certain other users (e.g.
>>>>> support
>>>>> > group) logged in as read only, and requiring them to enable manually.
>>>>> >
>>>>> > Ive seen some suggestions of using an optional av pair "brcd-role =
>>>>> admin"
>>>>> > in the TACACS config, but seems this is for VDX devices, and I am
>>>>> working
>>>>> > with ICX.
>>>>> >
>>>>> > The usual "priv-lvl = 15" that works with Cisco doesnt seem to
>>>>> apply, and Im
>>>>> > finding scant other information about how to do this other than
>>>>> specifying
>>>>> > "aaa authentication login privilege-mode", but that would have all
>>>>> users
>>>>> > enabled once they have logged in.
>>>>> >
>>>>> > My configs look like:
>>>>> >
>>>>> > aaa authentication enable default enable
>>>>> > aaa authentication login default tacacs+
>>>>> > aaa authorization commands 0 default tacacs+
>>>>> > aaa authorization exec default tacacs+
>>>>> > aaa accounting commands 0 default start-stop tacacs+
>>>>> > aaa accounting exec default start-stop tacacs+
>>>>> > aaa accounting system default start-stop tacacs+
>>>>> >
>>>>> > and on the TACACS server Ive tried:
>>>>> >
>>>>> > group = read_write {
>>>>> >     default service = permit
>>>>> >     acl = network_nets
>>>>> >
>>>>> >     service = exec {
>>>>> >         priv-lvl = 15
>>>>> >         optional brcd-role = admin
>>>>> >     }
>>>>> > }
>>>>> >
>>>>> > Or maybe the reason I cant find any information is because this just
>>>>> isnt
>>>>> > possible on a Brocade?
>>>>> >
>>>>> > Any help appreciated!
>>>>> >
>>>>> > Thanks
>>>>> > Tom
>>>>> >
>>>>> > _______________________________________________
>>>>> > foundry-nsp mailing list
>>>>> > [email protected]
>>>>> > http://puck.nether.net/mailman/listinfo/foundry-nsp
>>>>>
>>>>
>>>>
>>> _______________________________________________
>>> foundry-nsp mailing list
>>> [email protected]
>>> http://puck.nether.net/mailman/listinfo/foundry-nsp
>>>
>>
>>
>>
>> E-Mail to and from me, in connection with the transaction
>> of public business, is subject to the Wyoming Public Records
>> Act and may be disclosed to third parties.
>>
>
>

-- 

E-Mail to and from me, in connection with the transaction 
of public business, is subject to the Wyoming Public Records 
Act and may be disclosed to third parties.

_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp