Re: [f-nsp] Renumbering unit in a FCX stack

On Thu, 12 Jan 2017, Mike Allen wrote:

> Hey Jethro, the stack unconfigure me should work, but maybe try the 
> clean option:
> 
> 'Stack unconfigure me' will recover the unit to its startup 
> configuration before it joined the stack. 'Stack unconfigure clean' will 
> remove unit's startup configuration. These commands will reload the unit 
> and boot up as standalone unit.

n-corp-sw#stack unconfigure clean
This command is not available on standalone or Active Controller
n-corp-sw#sh stack
alone: standalone, D: dynamic config, S: static config
ID   Type         Role    Mac Address    Pri State   Comment
2  S FCX648S      alone   0024.38c0.bf80 128 local   None:0


     +---+
  2/1| 2 |2/2
     +---+
Current stack management MAC is 0024.38bf.fb00

Eventually, I found that "erase startup" also deleted the stacking.boot 
file as well as the startup config, which I suspect contains the stack 
membership data.  So did that and reloaded and I was back to being unit 1, 
then copied the config back fixing the ports along the way and I'm back in 
business!

Many thanks for the hints!

Jethro.

> 
> There is also a default config command, but I am not finding that right 
> now...that would do it as well. The stacking config is saved separately 
> from the running and startup config, that is why the unit number is 
> showing up still.
> 
> Mike
> 
> On Thu, Jan 12, 2017 at 12:20 PM, Jethro R Binks <[email protected]>
> wrote:
> 
> > All,
> >
> > I think the answer to this should be easy, but I'm unable to figure it
> > out!
> >
> > I have a unit that was taken out of an extant FCX stack.  It happens to be
> > unit 2.  I now want it to be unit 1.
> >
> > I've been through pages like
> > http://www.brocade.com/content/html/en/configuration-
> > guide/fastiron-08030b-switchstackingguidehttp://www.
> > brocade.com/content/html/en/configuration-guide/fastiron-
> > 08030b-switchstackingguide
> > and tried lots of variants of stack unconfigure me, stack disable, no
> > stack enable, but try as I might I cannot get this unit to revert to being
> > unit 1.  The recommendation of running "stack secure-setup" doesn't do
> > anything useful:
> >
> > SSH@#stack secure-setup
> > SSH@#Discovering the stack topology...
> >
> >
> > Selected Topology:
> >
> > Active  Id      Type          Mac Address
> >         2    FCX648S        0024.38c0.bf80
> >
> >
> > No other units were discovered...
> >
> > !
> > ver 08.0.10mT7f1
> > !
> > stack unit 2
> >   module 1 fcx-48-port-management-module
> >   module 2 fcx-cx4-2-port-16g-module
> >   module 3 fcx-xfp-2-port-10g-module
> >   priority 128
> >   stack-port 2/2/1 2/2/2
> > stack enable
> > stack mac 0024.38bf.fb00
> > ...
> >
> > Anyone any ideas?
> >
> >     UNIT 2: compiled on Jul 08 2015 at 16:18:42 labeled as FCXS08010m
> >
> > Jethro.
> >
> > .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .
> > Jethro R Binks, Network Manager,
> > Information Services Directorate, University Of Strathclyde, Glasgow, UK
> >
> > The University of Strathclyde is a charitable body, registered in
> > Scotland, number SC015263.
> > _______________________________________________
> > foundry-nsp mailing list
> > [email protected]
> > http://puck.nether.net/mailman/listinfo/foundry-nsp
> >
> 

.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .
Jethro R Binks, Network Manager,
Information Services Directorate, University Of Strathclyde, Glasgow, UK

The University of Strathclyde is a charitable body, registered in
Scotland, number SC015263.
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp