Re: [f-nsp] MTU problem Brocade Chassis: MLXe 4-slot
"Jörg Kost" <[email protected]>
| Newsgroups | gmane.network.nsp.foundry |
|---|---|
| Message-ID | <[email protected]> |
Hi Adrian, maybe I am late to the party, but seems your configuration works. 1510 + IP + ICMP => 1538 bytes 1511 + IP + ICMP + 3 bytes padding => 1542 (wont work) Regards Jörg On 28 Feb 2017, at 12:50, Adrian Luchian wrote: > Hi, > > We need to setup an L2 connection with MTU=1540 for a customer. After > changing default-max-frame-size to 2000 and issue reload, we still > can't get replies to icmp with size > 1500 bytes and df-bit set. > > > 1510 Byte, DF not set = OK > ================================= > hostname#ping x.x.x.x size 1510 > Type escape sequence to abort. > Sending 5, 1510-byte ICMP Echos to x.x.x.x, timeout is 2 seconds: > !!!!! > Success rate is 100 percent (5/5), round-trip min/avg/max = 4/7/8 ms > > > > 1511 Byte DF not set = not OK > ================================= > hostname#ping x.x.x.x size 1511 > Type escape sequence to abort. > Sending 5, 1511-byte ICMP Echos to x.x.x.x, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5) > > 1500 Byte, DF set = OK > ================================= > hostname#ping x.x.x.x size 1500 df-bit > Type escape sequence to abort. > Sending 5, 1500-byte ICMP Echos to x.x.x.x, timeout is 2 seconds: > Packet sent with the DF bit set > !!!!! > Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms > > > 1501 Byte, DF set = not OK > ================================= > hostname#ping x.x.x.x size 1501 df-bit > Type escape sequence to abort. > Sending 5, 1501-byte ICMP Echos to x.x.x.x, timeout is 2 seconds: > Packet sent with the DF bit set > ..... > Success rate is 0 percent (0/5) > > > #show max-frame-size > Default max frame size for ETH : 2000 > Default max frame size for POS : 4474 > Slot 1 Port 1 Port 2 Port 3 Port 4 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 5 Port 6 Port 7 Port 8 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 9 Port 10 Port 11 Port 12 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 13 Port 14 Port 15 Port 16 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 17 Port 18 Port 19 Port 20 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Slot 2 Port 1 Port 2 Port 3 Port 4 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 5 Port 6 Port 7 Port 8 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 9 Port 10 Port 11 Port 12 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 13 Port 14 Port 15 Port 16 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 17 Port 18 Port 19 Port 20 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Slot 3 Port 1 Port 2 Port 3 Port 4 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Slot 4 Port 1 Port 2 Port 3 Port 4 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 5 Port 6 Port 7 Port 8 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 9 Port 10 Port 11 Port 12 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 13 Port 14 Port 15 Port 16 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > Port 17 Port 18 Port 19 Port 20 > -------- -------- -------- -------- > 2000 2000 2000 2000 > > > Is there anything else to be changed to accomplish this? > > Best regards, > > Adrian Luchian _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp