Re: [f-nsp] CER - Creating VLANs via SNMP - cant set name?

Hi,

1.3.6.1.2.1.17.7.1.4.3 is read-only. Have a look at
1.3.6.1.4.1.1991.1.1.3.2.7.1.21 instead.

snmpwalk -v2c -c $COMMUNITY $IP 1.3.6.1.4.1.1991.1.1.3.2.7.1.21
iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.123 = STRING: "TEST2"
iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.124 = STRING: "VLAN124"
iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.125 = STRING: "VLAN125"
iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.126 = STRING: "VLAN126"

snmpset -v2c -c $COMMUNITY $IP iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.123 s 
HELLOMYFRIEND
iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.123 = STRING: "HELLOMYFRIEND"
iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.124 = STRING: "VLAN124"
iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.125 = STRING: "VLAN125"
iso.3.6.1.4.1.1991.1.1.3.2.7.1.21.126 = STRING: "VLAN126"


You can also take a look at some other tools than can configure advanced 
things via ssh or telnet or can inject whole configurations.

Some people use

Netmikto
https://github.com/ktbyers/netmiko

and there is also kind of official brocade client called clicrud
https://github.com/DavidJohnGee/clicrud

I did my own injection client a while ago to escape the python world.
https://github.com/ipcjk/brocadecli

Regards

Jörg

On 22 Jun 2017, at 10:58, Tom Storey wrote:

> Hi everyone,
>
> Im writing some scripts that create VLANs and assigns ports to them 
> via
> SNMP, and so far everything is working pretty good, except that when I
> create the VLAN, it doesnt seem to save the name that I supply along 
> with
> it. For example, when I execute the following command:
>
> snmpset -v2c -c.... x.x.x.x .1.3.6.1.2.1.17.7.1.4.3.1.1.123 s TEST
> .1.3.6.1.2.1.17.7.1.4.3.1.2.123 x 0x00 .1.3.6.1.2.1.17.7.1.4.3.1.4.123 
> x
> 0x00 .1.3.6.1.2.1.17.7.1.4.3.1.5.123 i 4
>
> VLAN 123 is created, but the name TEST is not applied:
>
> #sh vlan brief
>
> Configured PORT-VLAN entries: 5
> Maximum PORT-VLAN entries: 4095
> Default PORT-VLAN id: 1
>
> VLAN  Name       Encap ESI                              Ve    Pri 
> Ports
>
> ----  ----       ----- ---                              ----- --- 
> -----
>
> 1     DEFAULT-VL                                        -     -  
> Untagged
> Ports : e 1/1 to 1/24 e 2/1 to 2/4
> 123   [None]                                            -     -  
> Statically
> tagged Ports    : e 1/10 to 1/11
>
> FWIW the above command works fine on other switches that I am testing
> against, they all save the name as expected.
>
> Attempting to set the name afterwards via a separate snmpset doesnt 
> yeild
> any better results.
>
> Does anyone know what Im doing wrong here? Should I be poking a 
> different
> OID perhaps?
>
> Running:
>
> System: NetIron CER (Serial #: ....,  Part #: ....)
> Boot     : Version 5.6.0cT185 Copyright (c) 1996-2013 Brocade
> Communications Systems, Inc.
> Monitor  : Version 5.6.0cT185 Copyright (c) 1996-2013 Brocade
> Communications Systems, Inc.
> IronWare : Version 5.6.0dT183 Copyright (c) 1996-2013 Brocade
> Communications Systems, Inc.
>
> Software might be a bit old, could probably try a new version if 
> people
> think that might help.
>
> Cheers
> Tom
> _______________________________________________
> foundry-nsp mailing list
> [email protected]
> http://puck.nether.net/mailman/listinfo/foundry-nsp
_______________________________________________
foundry-nsp mailing list
[email protected]
http://puck.nether.net/mailman/listinfo/foundry-nsp